Operation Manual

English

LU9235

The screen aspect ratio is 16:10 and the projected picture is 16:10.

Lens

Wide Zoom

(LS2ST1)

Standard

(LS2SD2)

Throw ratio 1.1~1.3 1.54~1.93

Diagonal Image Width Image Height

Offset (A) O Distance Distance

Wide/Tele Wide/ Tele Wide Wide Wide Wide

(Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m)

80 2.03 68 1.72 42 1.08 2.1 0.054 23.3 0.592 75 1.90 88 2.24 104 2.65 131 3.33

100 2.54 85 2.15 53 1.35 2.6 0.067 29.1 0.740 93 2.37 110 2.80 131 3.32 164 4.16

120 3.05 102 2.58 64 1.62 3.2 0.081 35.0 0.888 112 2.84 132 3.36 157 3.98 196 4.99

150 3.81 127 3.23 79 2.02 4.0 0.101 43.7 1.111 140 3.55 165 4.20 196 4.98 245 6.24

200 5.08 170 4.31 106 2.69 5.3 0.135 58.3 1.481 187 4.74 220 5.60 261 6.63 327 8.31

300 7.62 254 6.46 159 4.04 7.9 0.202 87.4 2.221 280 7.11 331 8.40 - - - -

400 10.16 339 8.62 212 5.38 10.6 0.269 116 . 6 2.962 - - - - - - - -

Lens

Semi Long

(LS2LT1)

Long Zoom

(LS2LT2)

Wide Fix

(LS2ST3)

Throw ratio 1.93~2.9 3~5 0.778

Diagonal Image Width Image Height

Offset (A) O Distance Distance Distance

Wide/Tele Wide/ Tele Wide Wide Wide Wide NA

(Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m) (Inch) (m)

80 2.03 68 1.72 42 1.08 2.1 0.054 23.3 0.592 131 3.33 197 5.00 204 5.17 339 8.62 53 1.34

100 2.54 85 2.15 53 1.35 2.6 0.067 29.1 0.740 164 4.16 246 6.25 254 6.46 424 10.77 66 1.68

120 3.05 102 2.58 64 1.62 3.2 0.081 35.0 0.888 196 4.99 295 7. 50 305 7.75 509 12.92 79 2.01

150 3.81 127 3.23 79 2.02 4.0 0.101 43.7 1.111 245 6.24 369 9.37 382 9.69 636 16.15 99 2.51

200 5.08 170 4.31 106 2.69 5.3 0.135 58.3 1.481 327 8.31 492 12.49 509 12.92 848 21.54 132 3.35

300 7.62 254 6.46 159 4.04 7.9 0.202 87.4 2.221 491 12.47 738 18.74 763 19.39 1272 32.31 - -

400 10.16 339 8.62 212 5.38 10.6 0.269 116 . 6 2.962 655 16.63 984 24.99 - - - - - -

Note:

There is 5% tolerance among these numbers due to optical component variations. BenQ recommends that if you

intend to permanently install the projector, you should physically test the projection size and distance using the actual

projector before you permanently install it, so as to make allowance for this projector's optical characteristics. This will

help you determine the exact mounting position so that it best suits your installation location.