Datasheet H10 (Data-Only) HSDPA PCI Express mini card module Datasheet Rev. 0.2 (Preliminary) 2007/06/22 COPYRIGHT BENQ Corporation This document contains proprietary technical information which is the property of BenQ Corporation and is issued in strict confidential and shall not be disclosed to others parties in whole or in parts without written permission of BenQ Corporation The documents contain information on a product, which is under development and is issued for customer evaluation purposes only.
BenQ Corporation Mobile Communications BG 18 JiHu Road, Nei-Hu, Taipei 114, Taiwan, R.O.C. Tel: +886-2-2799-8800 Fax: +886-2-2656-6390 http://www.BenQ.com HISTORY Version Date Notes VER: 0.1 2007-APR-24 FIRST RELEASE VER: 0.
1. INTRODUCTION..................................................................................................... 4 1.1 Description.........................................................................................................4 1.2 Application Device..............................................................................................4 2. FEATURES ............................................................................................................... 5 2.
1. INTRODUCTION 1.1 Descrip便ion Overview This document describes all the functions, features, and interfaces of the HSDPA PCI Express Mini Card Module -- H10 from BenQ. BenQ H10 HSDPA module supports Tri-band WCDMA/HSDPA and Quad-band GSM/GPRS/EDGE network connection capability. BenQ H10 HSDPA card can provides high speed data connection, and the data speed of downlink path is up to 7.2Mbps.
2. FEATURES 2.1 General Charac便eris便ics Band BAND: GSM850/EGSM900/DCS1800/PCS1900/WCDMA850/WCDMA1900/WCDMA2100 TX RX GSM850 824~849 MHz 869~894MHz EGSM900 880~915 MHz 925~960MHz DCS1800 1710~1785MHz 1805~1880MHz PCS1900 1850~1910MHz 1930~1990MHz WCDMA850 824~849 MHz 869~894MHz WCDMA1900 1850~1910MHz 1930~1990MHz WCDMA2100 1920~1980MHz 2110~2170MHz Support SIM Interface: 1.8V/3V Form factor i. Dimension: 50.95 x 30 x 5.0 mm ii. Weight: 12g Power Operation Voltage: 3.
Hardware Interface: 52 Pins PCI Express Mini Card connector interface 2 RF Antenna Coaxial Connectors Software Interface: USB driver Qsyncher software tool. 2.2 RF Func便ionali便ies Maximum TX Power The performance of the transmitter meets test requirement ETSI TS 151 010-1 chapter 13.3 for GSM, chapter 13.17.3 for EDGE and TS 34.121 chapter 5.2&5.4.3 for WCDMA, chapter 5.
Sensi便ivi便y The performance of the receiver meets test requirement ETSI TS 151 010-1 chapter 14.2.1 for GSM, chapter 14.18.1 for EDGE and TS 34.121 chapter 6.2 for WCDMA. Band Typical Min GSM8S0 -107 dBm -104 dBm EGSM -107 dBm -104 dBm DCS -107 dBm -103 dBm PCS -107 dBm -103 dBm EDGE(GMSK modulation) -107 dBm -104 dBm EDGE(8-PSK modulation) -104 dBm -102 dBm UMTS-2100(Primary) -109 dBm -106.7 dBm UMTS-2100(Secondary) -109 dBm N/A UMTS-1900 -107 dBm -104.
Output Impedance S0 Ohm Spurious Emission -36 dBm up to 1 GHz (< -30 dBm > 1 GHz) Compatible with phase 2 feature PCS (1900 MHz) Frequency Range TX: 18S0~1910MHz; RX: 1930~1990MHz Channel Spacing 200KHz Number of Channels 299 Carriers x 8 (TDMA) Modulation GMSK / 8-PSK Duplex Spacing 80 MHz Frequency Stability +/- 0.
3. HARDWARE DESCRIPTION 3.1 Sys便em In便erface The I/O connectors of H10 module are PCI EXPRESS MINI CARD and two RF antenna connectors. Table 3-1 summarizes the 25 signals and 18 power lines that are supported by the PCI Express Mini Card System Interface. Table 3-2 shows the antenna interface. Signal Group Pin no. Table 3-1 System Interface Description Power S 3.3V power source GND 13 Return current path USB 2 USB serial data interface compliant to the USB 2.
3.
3.3 Pin Descrip便ion Pin Signal name Direction Description 1 NC No connect 2 +3.3Vaux 3 NC 4 GND 5 NC No connect 6 NC No connect 7 NC No connect 8 UIM_PWR Output Power source for the USIM 9 GND Power Return current path 10 UIM_DATA 11 NC 12 UIM_CLK 13 NC 14 UIM_RESET Output USIM reset signal 15 GND Power Return current path 16 NC No connect 17 NC No connect 18 GND 19 NC Power 3.
32 NC No connect 33 NC No connect 34 GND Power Return current path 35 GND Power Return current path 36 USB_D- 37 GND 38 USB_D+ Input / Output 39 +3.3Vaux Power 3.3V power source 40 GND Power Return current path 41 +3.3Vaux Power 3.3V power source 42 LED_WWAN# Output 43 GND Power 44 LED_WLAN# Output 45 NC 46 LED_WPAN# 47 NC No connect 48 NC No connect 49 NC No connect 50 GND 51 NC 52 +3.
3.
Sys便em connec便or 52 pins PCI Express Mini Card 1
3.5 Elec便rical Charac便eris便ics DC charac便eris便ics Pin Function/ Name 1 NC 2 +3.3Vaux 3 NC 4 GND S NC 6 NC 7 NC 8 UIM_PWR Direction Parameter Power Power Supply Voltage Power Ground Output Supply Voltage Min Typ GND Power 10 UIM_DATA Input / Output 11 NC 12 UIM_CLK 13 NC 14 UIM_RESET Output 1S GND Power Ground 16 NC 17 NC 18 GND Power Ground 19 NC 20 W_DISABLE# Unit 3.0 3.3 3.6 V 1.S 2.8S 3.
32 NC 33 NC 34 GND Power Ground 3S GND Power Ground 36 USB_D- Input / Output Termination Voltage 37 GND Power Ground 38 USB_D+ Input / Output 39 +3.3Vaux 40 3.0 3.3 3.6 V Termination Voltage 3.0 3.3 3.6 V Power Power Supply Voltage 3.0 3.3 3.6 V GND Power Ground 41 +3.3Vaux Power Power Supply Voltage 3.0 3.3 3.
Internal pull-up resistor 3.3V to D+, 3.3V to D- 1.42S 1.S 1.S7S KΩ Internal pull-down resistor D+ to GND, D- to GND 14.3 1S 24.8 KΩ USIM In便erface The USIM signals are defined on system connector to provide the interface between the removable User Identity Module. USIM interface usually run off either 1.8V or 3.0V.
3.
Bo便便om View 1
Side View 2
4. SOFTWARE CHARACTERISTICS 4.1 In便roduc便ion We provide the PC Tool – Qsyncher for H10 HSDPA card. The main functions in this tool are Contacts (only SIM card), SMS, Settings, and QMI. QMI is the independent network software; user can run this service alone without Qsycher active. 4.
5 Compliance with FCC Rules and Regulations 15.21 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.