FP73G LCD Color Monitor 17.0" LCD Panel Size User’s Manual Welcome Downloaded from ManualMonitor.
i Copyright Copyright © 2006 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.
i Table of Contents Getting started ...................................................................................................................... 5 Getting to know your monitor ............................................................................................ 6 Front View ...................................................................................................................6 Back View .............................................................................................
Table of Contents Downloaded from ManualMonitor.
111 1Getting started When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement. BenQ LCD Monitor Quick Start Guide CD-ROM Power Cord Signal Cable: D-Sub Signal Cable: DVI-D (optional) Consider keeping the box and packaging in storage for use in the future when you may need to transport the monitor. The fitted foam packing is ideal for protecting the monitor during transport.
121 1Getting to know your monitor Front View Back View 1. Power AC input jack 2. DVI-D Connector 3. D-Sub Connector 6 Getting to know your monitor Downloaded from ManualMonitor.
131 1How to assemble your monitor hardware If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to the monitor until instructed to do so. 1. Attach the monitor base. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty.
2. Connect the PC video cable. Either Do not use both DVI-D cable and D-Sub cable on the same PC. The only case in which both cables can be used is if they are connected to two different PCs with appropriate video systems. Connect one end of the DVI-D cable to the monitor DVI-D socket and the other end to the DVI-D port on your computer. (optional) The DVI-D format is used for direct digital connection between source video and digital LCD monitors or projectors.
4. Route the cables via the cable clip. Release the cable retaining clip by squeezing the clip inwards as illustrated. Position the cables together and reinsert the clip over them to retain the cables neatly in place behind the monitor stand. 5. Connect-to and turn-on the power. Plug the other end of the power cord into a power point and turn it on. Turn on the monitor by pressing the power button on the front of the monitor.
How to detach the stand base 1. Prepare the monitor and area. Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
How to use the monitor wall mounting kit The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please read the precautions carefully. Precautions: • Install your monitor and monitor mounting kit on a wall with flat surface. • Ensure that the wall material is stable to support the weight of the monitor.
3. Remove the rear cover. Pull around the edge of the rear cover and slightly lift it to reveal the screw plate at the back of the monitor. 4. Follow the instruction manuals of the wall mount bracket you purchased to complete the installation. To attach the rear cover: 1. Tilt the rear cover forward and insert the two tabs on the front edge into the recesses of the screw plate. No tools are required. 2. Position the two tabs on left side of the rear cover to fit into the grooves in the screw plate. 3.
141 1Getting the most from your BenQ monitor To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM. The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software.
How to install the monitor on a new computer This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver software on a new computer which has never had a monitor driver installed before. This instruction is only suitable for a computer which has never been used before, and for which the BenQ LCD Monitor is the first ever monitor to be connected to it.
How to upgrade the monitor on an existing computer This instruction details the procedure for manually updating the existing monitor driver software on your Microsoft Windows computer. It is currently tested as compatible (and recommended only) for Windows 2000, and Windows XP Operating System (OS).
How to install on Windows XP system 1. Open Display Properties. The quickest shortcut to Display Properties is through the Windows desktop. Right-click the desktop and select Properties from the popup menu. Alternatively, the Windows menu to Display Properties is located in Control Panel. In Windows XP version, Control Panel is located directly under the main Start menu item. The menu options displayed will depend upon which type of view is selected for your system.
How to install on Windows 2000 system You do not need to follow this instruction if you are installing onto a computer which has a Windows XP (or later) version system. In that case, see the instructions at How to install on Windows XP systems on page 16. 1. Open Display Properties. The quickest shortcut to Display Properties is through the Windows desktop. Right-click the desktop and select Properties from the popup menu. Alternatively, the Windows menu to Display Properties is located in Control Panel.
How to complete the Windows Upgrade Device Driver Wizard 1. Load the BenQ LCD Monitor CD-ROM which came with your monitor. Insert the CD-ROM into a CD drive on the computer you attached the monitor to. The autorun User’s Guide language selection page will display in your web browser. You can select a language and view the online version of this manual from the next window. You could then print it out for reference if you wish to work off-line.
This will close the Display Properties window, and if you made any changes to the screen resolution, Windows 2000 will prompt you for confirmation to effect the changes, and further confirmation to accept the changes. Click OK and Yes respectively. Getting the most from your BenQ monitor Downloaded from ManualMonitor.
151 1How to adjust the screen resolution Due to the nature of liquid crystal display (LCD) technology, the picture resolution is always fixed. The best possible picture for your FP73G is achieved with a resolution of 1280x1024. This is called “Native Resolution” or maximal resolution – that is, the clearest picture. Lower resolutions are displayed on a full screen through an interpolation circuit.
161 1How to adjust the screen refresh rate You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer. There is a table with the factory modes in the specification section of this User’s Manual. You can choose 60, 70 and 75 Hertz, (but not 72Hz) for the native resolution of 1280x1024. 1.
171 1How to set the picture optimization The easiest way to obtain an optimal display is to use the i key function. Press the i key to optimize and adjust the screen settings automatically for you. Refer to How to adjust your monitor on page 23 for button locations and functionality. If you wish to, you can always adjust the screen settings manually using the buttons on the monitor panel.
181 1How to adjust your monitor A look at the control panel There are 6 keys for user’s control including “iKey”, “Exit”, “Enter”, “<” and “>” key and a power switch. The following descriptions are the introduction of these keys & switch. 1. “iKey”: Adjust vertical position, phase, horizontal position and pixel clock automatically. 2. “Exit” key: Back to previous menu or exit OSD. This key is also the hot key for Input Select. 3. W (Left) key: For Left/Decrease adjustment.
Hot key mode The monitor keys perform as hotkeys to provide direct access to particular functions whenever the menu isn't currently displaying on-screen. Brightness hot key Press the X key to enter the Brightness menu. Further press the W or X keys to adjust the degree of screen brightness and press the Exit key to exit OSD. Contrast hot key Press the W key to enter the Contrast menu. Further press the W or X keys to adjust the degree of screen contrast and press the Exit key to exit OSD.
Main menu mode Press the Enter key to display the Main Menu. Use the W (left) or X (right) keys to highlight a menu item, and press the Enter key to display the Menu item settings. Main Menu Luminance sub-menu Press the W or X keys to adjust the degree of Brightness. Press the Exit key to return to previous menu. Press the W or X keys to adjust the degree of Contrast. Press the Exit to return to previous menu. How to adjust your monitor Downloaded from ManualMonitor.
Geometry sub-menu Press the W or X keys to adjust the display Horizontal Position. Press the Exit key to return to previous menu. Press the W or X keys to adjust the display Vertical Position. Press the Exit key to return to previous menu. . Press the W or X key to adjust the monitor Pixel Clock. Press the Exit key to return to previous menu. Press the W or X keys to adjust the degree of screen display Phase. Press the Exit key to return to previous menu.
Color sub-menu Bluish - applies a cool tint to the image and is factory pre-set to the PC industry standard white color. Reddish - applies a warm tint to the image and is factory pre-set to the news print standard white color. Normal - allows video and still photographs to be viewed with natural coloring. This is the factory default color. User Preset: User Preset is provided so you can tailor the image color tint to suit your liking.
OSD sub-menu Press the W or X keys to adjust the Horizontal Position of the OSD. Press the Exit key to return to previous menu. Press theW or Xkeys to adjust the Vertical Position of the OSD. Press the Exit key to return to previous menu. Press theW or X keys to adjust the display time of the OSD. Press the Exit key to return to previous menu. 28 How to adjust your monitor Downloaded from ManualMonitor.
Language sub-menu Press the W or X keys to select a language to have the OSD display menus in that language. Press the Exit key to return to previous menu. Picture may differ from the Language menu on your monitor, depending on the product supplied in your region. How to adjust your monitor Downloaded from ManualMonitor.
Recall sub-menu Press the W or X keys to select Color Recall. Press the Enter key to recall color settings, or press the Exit key to return to previous menu. Press the W or X keys to select Recall All. Press the Enter key to recall position and color settings, or press the Exit key to return to previous menu. 30 How to adjust your monitor Downloaded from ManualMonitor.
Miscellaneous sub-menu Input Select: Press the W or X keys to select D-sub (analog) or DVI (digital) input to activate the new settings. Press the Exit key to return to previous menu. Sharpness: Press the W or X keys to adjust the degree of Sharpness. Press the Exit key to return to previous menu. Display Information: Select Display Information to display the current monitor property settings. Press the Exit key to return to previous menu. How to adjust your monitor Downloaded from ManualMonitor.
191 1Troubleshooting Frequently asked questions (FAQ) The image is blurred: Read the How to adjust the screen resolution on page 20 section, and then select the correct resolution, refresh rate and make adjustments based on these instructions. How do you use a VGA extension cable? Remove the extension cable for the test.
The image is distorted, flashes or flickers: Read the How to adjust the screen resolution on page 20 section and then select the correct resolution, refresh rate and make adjustments based on these instructions. The image is displaced in one direction: Read the How to adjust the screen resolution on page 20 section and then select the correct resolution, refresh rate and make adjustments based on these instructions.
11 10 1Supported opearting modes Resolution 640x350 720x400 640x480 640x480 640x480 640x480 800x600 800x600 800x600 800x600 832x624 1024x768 1024x768 1024x768 1152x864 1152x870 1152x900 1152x900 1280x1024 1280x1024 1280x1024 1280x1024 Incoming display mode (Input timing) Horizontal Vertical Pixel Frequency (KHz) Frequency (Hz) Frequency (MHz) 31.47(P) 70.08(N) 25.17 31.47(N) 70.08(P) 28.32 31.47(N) 60.00(N) 25.18 35.00(N) 67.00(N) 30.24 37.86(N) 72.80(N) 31.50 37.50(N) 75.00(N) 31.50 35.16(P) 56.25(P) 36.
11 11 1Specifications BenQ FP73G Model FP73G Display type 17.0”, active, TFT Viewable diagonal 432 mm Native (maximum) resolution 1,280 x 1,024 Colors 16.
Operating voltage Automatic switched mode power supply, 90-264 V, 47-63 Hz 36 Dimensions (H x W x D) 363.8 x 356.5 x 135 mm Weight 3.7 kg Specifications Downloaded from ManualMonitor.
