Headset Bluetooth Clip Brand Name: BenQ-Siemens Model Name: HHB-130
Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE 2 Headset Bluetooth Clip (en) Safety precautions Please read the user guide and safety precautions carefully before use! Explain the content to your children and the hazards associated with using the device. Remember to comply with legal requirements and local restrictions when using the device. For example in aeroplanes, petrol stations, hospitals or while driving.
Headset Bluetooth® Stereo (en) Important: Dispose of unusable devices and their accessories according to the legal regulations. The device may cause interference in the vicinity of TV sets, radios and PCs. Use only original accessories. This will avoid potential damage to health or property and ensure compliance with all relevant regulations. Improper use will invalidate the guarantee! Permanent hearing loss may occur if you use ear- or headphones at high volume.
Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE 4 Headset Bluetooth Clip (en) Overview of headset 1 Earphone 2 a On/Off button/ Multifunction button Press briefly: Activate voice dialling or Accept a call Press and hold: End a call 3 Microphone 4 LED signals different headset states (page 8) 5 Volume buttons Press – button: quieter Press + button: louder 6 Clip Please ensure that the clip is securely attached to the garment.
Headset Bluetooth® Stereo (en) 9 5 Getting started Wearing the headset correctly Wear the headset as shown in the diagram. The microphoneopening must always point towards your mouth. Charging the headset The battery is not fully charged when delivered. To charge the headset you will need the charger included in the delivery package. Please remember that the power socket must be close by and freely accessible. Template: X75, Version 2.
Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE 6 Headset Bluetooth Clip (en) The battery should only be charged in an ambient temperature of 0°C to 45°C, otherwise it will wear out prematurely. Please remember that batteries are subject to wear. 1. Plug the charger 9 into the headset 7 as shown. 2. Plug the power connector of the charger into a mains power socket. The device is not ready for operation while charging.
Headset Bluetooth® Stereo (en) Switching the headset on and off • Switch on: a Press for about 2 seconds. The LED flashes at short intervals for 1 second, then at long intervals. A low and a high tone can be heard. If no connectable mobile phone can be found, please repeat pairing. • Switch off: a Press for about 3 seconds. The LED lights continuously for 1 second and then goes out. A high and a low tone can be heard.
Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE 8 Headset Bluetooth Clip (en) Meaning of the LED display Calling The flash sequence of the LED indicates the different operating states of the headset: The operating steps described below apply only to selected Siemens and BenQ-Siemens mobile phones; see compatibility table on the package. Mobile phones from other manufacturers may be operated differently. ... (when the charg- er is connected) The headset is charging.
Headset Bluetooth® Stereo (en) During calls + Louder. – Quieter. The volume set here does not affect the setting on the mobile phone. a Press 2 x briefly : Hold call. Press again 2 x briefly: Continue call. a Press and hold: End call. b a Press and hold: End Second call the current call. a Press briefly: Hold the current call and accept the waiting call. a Press 2 x briefly: Swap between two calls. a Press 2 x and hold: End all calls.
Template: X75, Version 2.2;VAR Language: unknown; VAR issue date: VAR_Issue_DATE 10 Headset Bluetooth Clip (en) Technical data and approval Headset Li-Ion battery 110 mAh Charging time up to 3.5 hours Talktime up to 8 hours Standby time up to 240 hours Bluetooth® range max. 10 metres, less in buildings Operating temperature –0°C to +55°C Total weight approx.
Headset Bluetooth® Stereo (en) Care The product should be cleaned with a soft cloth that is damp but not wet. Do not use cleaning agents, colorants or other chemical substances. Protect the device from dampness and shock. Do not expose the device to direct sunlight. Accessories Products can be obtained in specialist shopsor you can visit our online shop at: Original Accessories www.BenQMobile.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
