BENNING CFlex 1 Operating manual CFlex 1 3000 A Ø 16 cm/L 46 cm FLEXIBLE CURRENT PROBE
D F E I 6 CFlex 1 3000 A Ø 16 cm/L 46 cm FLEXIBLE CURRENT PROBE 7 Bild 1: Fig. 1: Fig. 1: Fig. 1: Obr. 1: Σικόνα 1: Gerätefrontseite Appliance front face Partie avant de l‘appareil Parte frontal del equipo Přední strana přístroje Μπροστινή όψη 07/ 2014 Ill. 1: Fig. 1: Rys. 1: Рис.
D F E I Bild 2 a: Wechselstrommessung Fig. 2 a: Alternating current measurement Fig. 2 a: Mesure de courant alternative Fig. 2 a: Medición de corriente alterna obr. 2 a: Měření střídavého proudu Σικόνα 2 a: Μέτρηση εναλλασσόμενης έντασης ρεύματος ill. 2 a: Fig. 2 a: Rys.2 a: Рис.
D F E I 25 mm 50 mm 75 mm Bild 3: Fig. 3: Fig. 3: Fig. 3: Obr. 3: Σικόνα 3: Positionierungsfehler Positioning error Erreur de positionnement Error de posición Poziční chyba Σφάλμα θέσης Ill. 3: Fig. 3: Rys. 3: Рис. 3: Resim 3: Errore di posizione Positionering foutmarge Błąd położenia Погрешность позиционирования Pozisyon hatası Bild 4: Fig. 4: Fig. 4: Fig. 4: Obr.
Operating Instructions BENNING CFlex 1 Flexible AC current transformer for AC current measurement Table of contents 1. User notes 2. Safety note 3. Scope of delivery 4. Unit description 5. General information 6. Ambient conditions 7. Electrical specifications 8. Measuring with the BENNING CFlex 1 9. Maintenance 10. Environmental note 1. User notes These operating instructions are intended for - qualified electricians and electrotechnically trained persons.
2. Safety note The instrument is built and tested in accordance with DIN VDE 0411 part 1/ EN 61010-1 DIN VDE 0411 part 2-032/ EN 61010-2-032 DIN VDE 0411 part 031/ EN 61010-031 and has left the factory in perfectly safe technical condition. To maintain this condition and to ensure safe operation of the unit, the user must observe the notes and warnings given in these instructions at all times. Improper handling and non-observance of the warnings might involve severe injuries or danger to life.
5.1.6 5.1.7 5.1.8 5.1.9 5.1.10 5.1.11 6. - - Length of the measuring loop: approx. 46 cm Cable diameter of the measuring loop: approx. 8.5 mm Cable length from measuring loop to housing: approx. 1.8 m Cable length (housing to the 4 mm safety plugs): approx. 0.5 m Housing dimensions: (L x W x H) = 120 x 70 x 26 mm Weight of the device: 325 g Ambient conditions The BENNING CFlex 1 is intended for making measurements in dry environment.
ble readings and measuring errors. Do not apply any voltage to the output contacts of the BENNING CFlex 1. - Do not exceed the maximum permitted voltage with respect to earth potential! Electrical danger! The highest voltage that may be applied to the BENNING CFlex 1 with respect to earth potential is 600 V CAT III / 1000 V CAT II. 8.2 AC current measurement Select the measuring range (30 A, 300 A or 3000 A) by means of the rotary switch 3.
9.3 Battery replacement Before opening the BENNING CFlex 1, make sure that it is free of voltage! Electrical danger! The BENNING CFlex 1 is supplied by means of two 1.5 V batteries of type AAA (IEC LR03). Battery replacement (see figure 4) is required, if the red LED (battery indication) 6 lights. Proceed as follows to replace the batteries: Remove the BENNING CFlex 1 from the object to be measured. Disconnect both safety plugs of the safety measuring lead from the multimeter.
Benning Elektrotechnik & Elektronik GmbH & Co. KG Münsterstraße 135 - 137 D - 46397 Bocholt Telefon ++49 (0) 2871 - 93 - 0 • Fax ++49 (0) 2871 - 93 - 429 www.benning.de • eMail: duspol@benning.
