Owner's Manual

ManualsBrandsBenjamin ManualsAirgunsDiscovery Rifle, Pump & Scope Combo

• With the bolt in the rearward position, place one pellet, nose ﬁrst, into the loading port

(breech) (ﬁg. 6). This is a single shot pellet airgun. Load no more than one pellet

at a time.

• Lightly push the pellet into the barrel by closing the bolt and pushing the bolt handle

down to lock. DO NOT jam the bolt forward. This will damage your airgun.

• Be sure the bolt is closed and locked before ﬁring. If it is not closed and fully locked,

the pellet may not be discharged.

B. Unloading Pellets and Uncocking Your Air Gun

Unloading

• The most common way to unload a pellet is to ﬁre your airgun in a SAFE DIRECTION

following Section 5 on Aiming and Firing Safely. If a pellet has become lodged in the barrel follow the steps in

section 6 Removing a Jammed Pellet.

Un-cocking

• To uncock the action, take the airgun “OFF SAFE.” With the muzzle pointed in a SAFE DIRECTION, open the bolt

and pull all the way to the rear. Holding the bolt handle securely, pull the trigger with your other hand and slowly

ease the bolt as far forward as it will go with your hand. You may now lower the bolt and the airgun is un-cocked.

• Put the airgun “ON SAFE”.

5. Aiming and Firing Safely

A. Aiming the Airgun

• Always point your airgun in a

SAFE DIRECTION.

• Follow the instructions for ﬁlling

the air gun (section 3A) and

loading pellets (section 4A).

• You and others with you should

always wear shooting glasses

to protect your eyes.

• Do not shoot at hard surfaces or

at the surface of water. The

pellet may bounce off or ricochet and hit someone or something you had not intended to hit.

• Always choose your target carefully. It is best to shoot at paper bull’s-eye targets which are attached to a safe

backstop. A heavy blanket should be hung behind the backstop to prevent ricochet should you miss the backstop.

• Your airgun is designed for target shooting and is suited for both indoor and outdoor use. Always remember to

place your target carefully. THINK about what you will hit if you miss the target.

• The airgun is correctly aimed when the front sight blade is positioned exactly in the center of the notch of the rear

sight. The top of the front sight blade should be even with the top of the notch in the rear sight. The bulls-eye

should appear to rest on the top of the front sight. (Fig 7)

• Before ﬁring the airgun make certain there is sufﬁcient pressure for proper operation. (see Figure 5).

B. Adjusting the sights

• The rear sight may be adjusted to shoot higher or lower (elevation). Move the rear sight elevator back to make

pellet hit higher on the target. Move the rear sight elevator forward to make the pellet hit lower on the target.

When moving the elevator, slightly lift the rear sight with one hand, and move the elevator with the other hand and

reset it on the desired notch.

• The rear sight may also be adjusted to shoot right or left (windage). Loosen the windage adjustment screws by

turning them counterclockwise. Move the sight to the right to make the pellet hit to the right on the target. Move

the sight to the left to make the pellet hit to the left of the target. Then tighten the windage adjustment screws by

turning them clockwise.

6. Removing a Jammed Pellet

A jammed pellet is usually the result of trying to ﬁre the airgun when the pressure is too low. Before ﬁring the airgun make

certain there is sufﬁcient pressure for proper operation. The gauge needle should be pointing to an area in the green zone

on the gauge (see Figure 5).

WARNING:

In this procedure you will put a cleaning rod down the barrel of a charged

airgun. It is extremely important that while you are doing this that the airgun be “ON SAFE”, the

bolt remain in open position and that your nger be kept away from the trigger. Always keep

the airgun pointed in a safe direction. Failure to follow this warning may result in serious injury

or death.

• Point the airgun in a SAFE DIRECTION.

• Put the airgun “ON SAFE”.

• Open the bolt by pushing the bolt handle up and pulling it all the way back until you hear two clicks.

• With the bolt in the rearward position insert a ramrod of the proper size into the barrel (start at the muzzle).

The barrel could be damaged if the proper sized cleaning rod is not used

NOTE: The bolt must be cocked and open for the jammed pellet to clear the breech when it is pushed out by the ram rod.

• Using the ramrod push the pellet into the pellet loading port (forward of the bolt), remove and discard the pellet.

Do not reuse that pellet.

• Point the airgun in a SAFE DIRECTION, close the action take “OFF SAFE” and ﬁre. Put the airgun “ON SAFE”.

• If you are not able to unjam your airgun by following this procedure, take no further action. Crosman Corporation or

an Authorized Service Station will unjam your airgun. (no cost during the warranty period)

7. Maintaining Your Airgun

• Put one drop of Crosman silicone chamber oil (part number RMCOIL) on the O-ring on the nose of the bolt every

6 months or every 2,000 shots.

• DO NOT use petroleum-based lubricants with this airgun.

• Keep all petroleum-based lubricants away from the ﬁll nipple. They MUST NOT be introduced into the high pressure

chamber. Use of petroleum-based lubricants in this area could result in an explosion resulting in personal injury.

• DO NOT MODIFY OR ALTER YOUR AIRGUN. Attempts to modify the airgun in any way inconsistent with this

manual may make your airgun unsafe to use, cause serious injury or death, and will void the warranty.

• If you drop your airgun, visually check to see that it works properly before you use it again. If anything seems

changed, like a shorter or weaker trigger pull, this may mean worn out or broken parts. Call Crosman customer

service for assistance before using your airgun again.

8. Reviewing Safety

• Never point the airgun at any person or at anything you do not intend to shoot.

• Always treat the airgun as though it is loaded and with the same respect you would a ﬁrearm.

• Always aim in a SAFE DIRECTION. Always keep the muzzle of the airgun pointed in a SAFE DIRECTION.

• Always keep the airgun on safe until you are ready to shoot.

• Always check to see if the airgun is “ON SAFE” and unloaded when getting it from another person or from storage.

• Always keep your ﬁnger off the trigger and out of the trigger guard until ready to shoot.

• You and others with you should always wear shooting glasses to protect your eyes.

• If your reading or prescription glasses are not safety glasses, make sure you wear shooting glasses over your

regular glasses.

• Use .177 caliber (4.5mm) pellets only in your .177 caliber Benjamin Discovery or use .22 caliber (5.5 mm) pellets

only in your .22 caliber Benjamin Discovery. Never reuse ammunition. Use of any other ammunition can cause

injury to you or damage to the airgun.

• Do not shoot at hard surfaces or at the surface of water. The pellet may bounce off or ricochet and hit someone or

something you had not intended to hit.

• Place the backstop in a location that will be safe should the backstop fail.

• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and will

eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.

• Do not attempt to disassemble or tamper with your airgun. Use an Authorized Service Station. Using unauthorized

repair centers or modifying the function of your airgun in any way may be unsafe and will void your warranty.

• Always keep your CrosBlock® trigger block in place when storing this airgun. Store the airgun in a secure location.

(See CrosBlock instructions packaged with this airgun for assistance)

• Before you store your airgun make sure it is not loaded or cocked. Store this airgun charged with compressed air or

to keep the valves closed against dirt.

• Whenever you store the airgun, make sure it is “ON SAFE.”

SPECIFICATIONS

Mechanism Bolt action single shot

Power source Compressed air or CO

(CO

requires an optional ﬁll adapter)

Caliber/ammunition Model BP1K77 - .177 caliber lead pellet

Model BP9M22 - .22 caliber lead pellet

Weight 5.2 lbs

Length 39 inches

Barrel Riﬂed steel

Safety Cross bolt

REPAIR SERVICE

If your airgun needs repair, we recommend you take or send it to your nearest Crosman Authorized Service Station. DO NOT

ATTEMPT TO DISASSEMBLE IT! Your airgun requires special tools and ﬁxtures to repair it. Any disassembly or modiﬁcation not

performed by an Authorized Service Station will void the warranty.

A SPECIAL CUSTOMER SERVICE

Crosman Authorized Service Stations will unjam your airgun at no cost during the warranty period.

LIMITED ONE YEAR WARRANTY

This product is warranted to the retail consumer for one year from date of retail purchase against defects in material and work-

manship and is transferable. To register the serial number of your airgun, please return the airgun registration form. The warranty

is not conditioned on the return of the card. You should retain the original sales receipt as record of date of purchase.

WHAT IS COVERED

Replacement parts and labor. Transportation charges to consumer for repaired product.

WHAT IS NOT COVERED

Transportation charges to Authorized Service Station for defective product. Damages caused by abuse, modiﬁcation or failure to

perform normal maintenance – see Owner’s Manual. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES,

OR INCIDENTAL EXPENSES INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU.

HOW TO OBTAIN WARRANTY PERFORMANCE

U.S. Customers- Locate nearest service station (see www.Crosman.com or call Crosman customer service at 800-724-7486 for

list of stations). The service station will give you details of how to proceed with sending the item in for repair. You must contact the

station prior to shipping your product.

International Customers- Please return product to your nearest distributor. If you do not know your distributor, please call 585-

657-6161 and ask for our International Department for assistance.

IMPLIED WARRANTIES

ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-

LAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM DATE OF RETAIL PURCHASE. SOME STATES DO NOT AL-

LOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

To the extent any provision of this warranty is prohibited by federal, state or municipal law, which cannot be preempted, it shall not

be applicable. This warranty gives you speciﬁc legal rights and you may also have other rights, which vary, from state to state.

CROSMAN and CROSBLOCK are registered trademarks of Crosman Corporation in the United States.

WARNING:

Not a toy. This airgun is recommended for adult use only. Misuse or careless

use may cause serious injury or death. May be dangerous up to 600 yards (549 meters).

WARNING:

Do not brandish or display this airgun in public—it may confuse people and

may be a crime. Police and others may think it is a rearm. Do not change the coloration and

markings to make it look more like a rearm. That is dangerous and may be a crime.

THIS AIRGUN IS INTENDED FOR USE BY ADULTS ONLY

WARNING:

Lead pellets. Do not inhale dust or put pellets in mouth. Wash hands after

handling. This product contains lead, a chemical known to the State of California to cause cancer

and birth defects (or other reproductive harm.)

WARNING:

Use only compressed air in this airgun. When using Crosman’s optional CO2

adapter, you may use CO2. Use no other gasses—including oxygen, which can cause a re or

explosion that may result in serious injury or death.

WARNING:

Use only compressed air in this airgun. When using Crosman’s optional CO

adapter, you may use CO

. Use no other gasses, including oxygen, which can cause a re or

explosion that may result in serious injury or death.

WARNING:

Do not attempt to repair the airgun or to disassemble to correct an over ll

or valve lock. Parts can y from the airgun at dangerous speeds when it is disassembled while

pressurized.

WARNING:

Use .177 caliber pellets only in your .177 caliber Benjamin Discovery and .22

caliber pellets only in your .22 caliber Benjamin Discovery. Never reuse ammunition. Use of any

other ammunition can cause injury to you or damage to the airgun.

WARNING:

In this procedure you will put a cleaning rod down the barrel of a charged

airgun. It is extremely important that while you are doing this that the airgun be “ON SAFE”, the

bolt remain in open position and that your nger be kept away from the trigger. Always keep

the airgun pointed in a safe direction. Failure to follow this warning may result in serious injury

or death.