Operating instructions

USER INTERFACE
STRAP HOLE
EARPHONE
DISPLAY
-GSM status
-GPS status
-Battery status
-Indicator icons
KEYS
TWIG SOS BUTTON
-Emergency calls
-Emergency reports
SEND KEY
-Answer calls
END KEY
-Rejecting/end calls
-Cancel some operations
-Power on/off
NUMBER KEYS
-Information call/sending
position
-Amber Alert functions
-Man Down control
MICROPHONE
LOUDSPEAKER
(not in all models)
SIM HOLDER
SYSTEM CONNECTOR
-connecting charger or
data cable to the device.
DISPLAY INDICATORS
DEVICE IN STAND-BY MODE
GSM
NETWORK
INDICATORS
BATTERY
INDICATOR
TELEMATICS
FEATURES
INDICATORS
GPS POSITIONING
INDICATORS
NETWORK
OPERATOR/SERVICE
PROVIDER IDENTIFIER
BATTERY STATUS
/
The level indicates charge left in the battery.
During charging, the battery icon is changed to
indicate this event.
GSM/GPRS NETWORK STATUS
GSM is on
GPRS is used for telematics
GPRS is active for telematics
GSM is roaming . Phone is using other than
home network. Call and position transmissions
are charged according to roaming agreements.
Position transmissions may have been blocked
automatically.
Bars on top of the network status icon indicate
the strength of the GSM network. The more bars
the better the GSM network.
- Four bars - high network strength
- No bars - no network
GENERAL STATUS ICONS
/
TWIG SOS /TWIG SOS call is active.
TWIG SOS in is post emergency mode. Position
requests are possible from emergency numbers
Tracking is active to one or more destinations
/
Man Down Alert is active / failed. Automated
emergency cycles are possible
/
Wireless Alert ( wrist alert) connection available /
failed
Amber Alert / Condition Check is activated.
Automated emergency cycles are possible
GPS POSITIONING STATUS
GPS is active
GPS is sleeping
GPS is not available
Bars on top of the network status icon indicate
the accuracy of the last GPS position. The more
bars and the taller the bars, the better the
accuracy. If the position is older than 1 – minute
the signal bars are shown as wire frames
DISPLAY/TONE NOTIFICATIONS
GENERAL NOTIFICATIONS
Processing. An operation is in progress, please
wait.
General failure. Shown when an operation fails.
E.g. if you try to make a call when there is no
number pre-configured in the device.
Simultaneously, the Failure tone is played.
SIM failure. Shown when there is no SIM card
inserted in the device, or if the PIN code was
rejected. Simultaneously, the Failure tone is
played.
CHARGING NOTIFICATIONS
Battery low. Shown when there is a need to
recharge the battery. Simultaneously, the
Battery low tone is played.
The device is connected to a charger. Settings
during battery loading take place.
Simultaneously, the Charging tone is played.
The device is disconnected from a charger.
Settings during battery loading are ended, the
device returns to normal operation.
NOTIFICATIONS REFERRING CALLS OR MESSAGES
Normal incoming call. If available, the name
associated with the calling number/the phone
number itself is shown on the bottom. Shown
until the call is answered (to answer, press
SEND KEY).
Initiating information call or position report. Press
the corresponding number key and hold it down
while this notification is shown.
Sending a position report. Simultaneously, the
Message sending tone is played.
Making an information call. Shown until the call
is answered.
A call is in progress. Shown while the call is
connected.
START EMERGENCY CYCLE NOTIFICATIONS (DISPLAYS ON)
Starting emergency cycle (a long press):
Emergency tone settings are switched on. Press
the TWIG SOS button and hold it down until the
wedges are all turned black.
Starting emergency cycle (two quick presses):
Press the TWIG SOS button briefly. Emergency
tone settings are switched on. Press the button
again when the second circle starts blinking.
Emergency cycle cancellation period. A
countdown timer is shown on the bottom. The
timer counts the cancellation time left (in
seconds). Simultaneously, the Cancellation tone
is played. To cancel the emergency cycle, do it
while this notification is shown (by pressing the
END KEY).
OTHER EMERGENCY CYCLE NOTIFICATIONS (DISPLAYS ON)
Emergency cancellation. Shown right after the
emergency cycle was cancelled.
Emergency completion. Shown when the
emergency cycle ends normally, or when the
emergency mode is ended manually.
Emergency call retry. Emergency numbers can
be voice call numbers. The notification is shown
when the device makes another call attempt to a
number.
Emergency mode/Working. The device is
through with emergency calls, but sending
messages, message confirmation or position
refresh is still going on.
Emergency confirmation message received.
After receiving confirmation, the device will end
resending of an emergency message.
Simultaneously, the Message reception tone is
No metal
sticker here