IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS DOCUMENT. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
12,000 POUND CAPACITY SURFACE MOUNTED TWO-POST LIFTS This instruction manual has been prepared especially for you. Your new lift is the product of over 40 years of continuous research, testing and development; it is the most technically advanced lift on the market today. READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS. RECORD HERE THE LIFT AND POWER UNIT INFORMATION WHICH IS LOCATED ON THE SERIAL NUMBER DATA PLATES ON THE LIFT AND ON THE POWER UNIT Power Unit Model # Power Unit Date Of Mfg.
OWNER’S RESPONSIBILITY IMPORTANT NOTICE To maintain the lift and user safety, the responsibility of the owner is to read and follow these instructions: Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures. Never attempt to lift components without proper lifting tools such as forklift or cranes. Stay clear of any moving parts that can fall and cause injury.
Contents TABLE OF CONTENTS Page No. Warranty / Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Definitions of Hazard Levels . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Owner’s Responsibility . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLER / OPERATOR PLEASE READ AND FULLY UNDERSTAND. BY PROCEEDING YOU AGREE TO THE FOLLOWING. Failure to follow Danger, Warning, and Caution instructions may lead to serious personal injury or death to operator or bystander or damage to property. t I have visually inspected the site where the lift is to be installed and verified the concrete to be in good condition and free of cracks or other defects.
INTRODUCTION 1. Carefully remove the crating and packing materials. CAUTION! Be careful when cutting steel banding material as items may become loose and fall causing personal harm or injury. 2. Check the voltage, phase, and proper amperage requirements for the motor shown on the motor plate. Electrical work should be performed only by a certified electrician. IMPORTANT SAFETY INSTRUCTIONS Read these safety instructions entirely.
TOOLS REQUIRED t t t t t t t Rotary Hammer Drill or Similar 3/4” Masonry Bit Hammer 4 Foot Level Open-End Wrench Set: SAE/Metric Socket And Ratchet Set: SAE/Metric Hex-Key / Allen Wrench Set t t t t t t t Large Crescent Wrench Large Pipe Wrench Crow Bar Chalk Line Medium Flat Screwdriver Tape Measure: 25 Foot Minimum Needle Nose Pliers IMPORTANT NOTICE These instructions must be followed to ensure proper installation and operation of your lift.
When removing the lift from shipping angles, pay close attention as the posts can slide and can cause injury. Prior to removing the bolts make sure the posts are held securely by a fork lift or some other heavy lifting device. PARTS INVENTORY Be sure to take a complete inventory of parts prior to beginning installation.
FLOOR PLAN X X Note: Power Unit can be located at either “X” location. MODEL XPR-12FDL XPR-12FDL-LWB Lifting Capacity 12,000Lbs. / 5443Kg. 12,000Lbs. / 5443Kg. *Max Capacity/ Front Axle 6,000Lbs. / 2722Kg. 6,000Lbs. / 2722Kg. *Max Capacity/ Rear Axle 6,000Lbs. / 2722Kg. 6,000Lbs. / 2722Kg. A- Height Overall: 144" / 3403mm. 144” / 3403mm. B -Width Overall (Outside of Base Plate) 155" / 3937mm. 155" / 3937mm. 2" / 51mm. 2” / 51mm. F -Reach (Front Arm Min.): 39" / 991mm.
CLEARANCES XPR-12FDL 6" 152mm MINIMUM TO NEAREST WALL 3" 76mm MINIMUM TO NEAREST BAY OR OBSTRUCTION 1 22 2 " 571mm 136" 3453 MINIMUM TO NEAREST OBSTRUCTION 1 109 2 " 2781 3 160 4 " APPROACH 4082 MINIMUM TO NEAREST OBSTRUCTION LIFT HEIGHT CLEARANCE NOTE: There must be 70” plus the height of typical vehicle MIN distance from top of lift to nearest obstruction.
STEP 3 (Column Preparation) NOTE: REFER TO STEP 10 FOR CABLE ROUTING DETAILS. ROUTE BUTTON END OF CABLES PRIOR TO RAISING UP THE POSTS. COMPLETE THE FOLLOWING PRIOR TO RAISING THE COLUMNS 1. Prior to raising posts, slide each carriage upwards to expose the cylinder port in the base of the hydraulic cylinder and to aid in sheave removal and equalizer cable routing. (See Fig 3.1) Fig 3.
SITE LAYOUT / FLOOR PLAN A Model XPR-12FDL A 155” / 3937 mm STEP 4 (Site Layout) Capacity 12,000 LBS 4. Once a location is determined, use a carpenters chalk line to layout a grid for the Column locations. Keep all dimensions square within 1/8” (3mm) or malfunctioning of the lift can occur. 1. Determine which side of the lift will be the approach side. 5.
STEP 5 (Installing the POWER SIDE Column) 5. If shimming is required, insert the shims as necessary under the base plate so that when the anchor bolts are tightened, the posts will be plumb. 1. Before proceeding, double the check measurements and make certain that the base plate of each Column is aligned with the chalk line. 6. With the shims and anchor bolts in place, tighten by securing the nut to the base then turning 3-5 full turns clockwise. DO NOT use an impact wrench for this procedure. (See Fig.
STEP 7 (Mounting the Hydraulic Power Unit) 1. Attach the power unit to the POWER SIDE Column. Install the vibration dampener between the power unit and the power unit mounting plate on the Power Side Column, using four M8 hex head bolts and nuts supplied. (See Fig 7.1) DO NOT RUN POWER UNIT WITHOUT OIL. DAMAGE TO POWER UNIT PUMP CAN OCCUR. THE POWER UNIT MUST BE KEPT DRY. DAMAGE TO POWER UNIT CAUSED BY WATER OR OTHER LIQUIDS SUCH AS DETERGENTS, ACID ETC., IS NOT COVERED UNDER WARRANTY. Fig 7.
Fig 8.2 Torsion Spring Route safety cable over Off Side safety sheave and down towards Floorplate Safety Clevis Pin NOTE: Column cut away for clarity Hairpin Cotter Safety Cable Fig 8.4. Fig 8.5 Off Side Safety Weldment Safety Cable 2. From the Off Side Column insert the non-looped end of the safety cable through the hole located to the right of the Off Side safety weldment. (See Fig 8.3) Fig 8.
STEP 9 (Installing Hydraulic Lines) 7. Pull the slack out the safety cable and keep tension on the cable as nuts are being tightened. Tighten jam nuts on either side of the cable keeping the cable centered to the hole to secure it into place. (See Fig 8.7) NOTE: FOR THE WIDE CONFIGURATION, A 13” EXTENSION MUST BE INSTALLED TO THE CROSSOVER HOSE. A JIC TO JIC STRAIGHT FITTING HAS BEEN PROVIDED TO CONNECT THE CROSSOVER HOSE TO THE EXTENSION HOSE IN THE PARTS BOX.
WHEN ROUTING HYDRAULIC HOSES THROUGH THE POSTS, ROUTE HOSES THROUGH THE HOSE CLIPS WELDED ON EACH POST. MAKE SURE THAT THE HOSE IS CLEAR OF ANY MOVING PARTS. IT MAY BE NECESSARY TO TIE THE HOSES CLEAR BY USING NYLON TIE STRAPS OR WIRE. FAILURE TO KEEP THE HYDRAULIC HOSES CLEAR MAY RESULT IN THE HYDRAULIC HOSES TO FAIL, WHICH MAY RESULT IN DAMAGE OR PERSONAL HARM. MAKE SURE THAT THE SAFETY LOCKS ON EACH POST ARE FULLY ENGAGED BEFORE ATTEMPTING TO ROUTE EQUALIZER CABLES AND/OR HOSES.
Fig 10.3 From base plate sheave Threaded cable end comes down from Top Plate sheave and into hole on top of carriage plate. To lift head carriage NOTE: Column cut away for clarity NOTE: Column cut away for clarity 4. Insert the threaded end of the cable through the hole on top of the carriage. Place M18 washer and M18 Nylock nut on threaded cable end. Tighten cable nuts until taut, checking that both cables have equal tension. (See Fig 10.4) Fig. 10.
STEP 11 (Installing Floor Plate and Safety Cover) Lift Head Pin Lift Head Pin 1. After safeties have been adjusted and checked for proper operation, install and tighten Power Side safety cover and Off Side safety cover mounting screws. (See Fig. 11.1) Lift Head Fig. 11.1 Snap Ring Snap Ring Fig. 12.1 Lift Head Pin Lift Head Pin Screw Snap Ring 2. Install the floor plate between the columns as shown. (See Fig. 11.2) Fig. 12.2 Fig. 11.2 THE ARM RESTRAINT GEARS MUST BE POSITIONED PROPERLY.
Fig. 14.4 NOTE: EACH ARM RESTRAINT ASSEMBLY MUST BE INSPECTED BEFORE EACH AND EVERY TIME THE LIFT IS OPERATED. DO NOT OPERATE THE LIFT IF ANY OF THE FOUR ARM RESTRAINT SYSTEMS ARE NOT FUNCTIONING PROPERLY. 6. Ensure that the arms do not move when a force of approximately 100 pounds or less is applied laterally to the fully extended arms. REPLACE BROKEN COMPONENTS OR COMPONENTS WITH BROKEN TEETH ONLY WITH AUTHORIZED OR APPROVED REPLACEMENT PARTS.
CARRIAGE STOP BOLT INSTALLATION WARNING YOU MUST RE-INSTALL TOP CARRIAGE-STOP BOLT (SHOWN BELOW). TIGHTEN CARRIAGE-STOP BOLT TO 2-3 FT.-LBS. OF TORQUE UPON FINAL INSTALLATION INSPECTION. THESE INSTRUCTIONS MUST BE FOLLOWED TO ENSURE PROPER INSTALLATION AND OPERATION OF YOUR LIFT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY AND/OR DEATH AND/OR VOID PRODUCT WARRANTY.
DO NOT PERFORM ANY MAINTENANCE OR INSTALLATION OF ANY COMPONENTS WITHOUT FIRST ENSURING THAT ELECTRICAL POWER HAS BEEN DISCONNECTED AT THE SOURCE OR PANEL AND CANNOT BE RE-ENERGIZED UNTIL ALL MAINTENANCE AND/OR INSTALLATION PROCEDURES ARE COMPLETED. IMPORTANT POWER-UNIT INSTALLATION NOTES n DO NOT run power unit without oil. Damage to pump can occur. n The power unit must be kept dry. Damage to power unit caused by water or other liquids such as detergents, acid etc., is not covered under warranty.
STEP 13 (Power Unit Connection) STEP 14 (Lift Start Up / Final Adjustments) 1. Have a certified electrician run the power supply to motor. Refer to the data plate found on the motor for proper power supply and wire size. DURING THE START-UP PROCEDURE, OBSERVE ALL OPERATING COMPONENTS AND CHECK FOR PROPER INSTALLATION AND ADJUSTMENT. DO NOT ATTEMPT TO RAISE VEHICLE UNTIL A THOROUGH OPERATIONAL CHECK HAS BEEN COMPLETED.
STEP 16 (Bleeding the Cylinders) POST-INSTALLATION CHECK-OFF n n n n n n n n n n n n n Columns properly shimmed and stable Anchor Bolts tightened Pivot / Sheave Pins properly attached Electric power supply confirmed Cables adjusted properly Safety Locks functioning properly Check for hydraulic leaks Oil level L ubrication of critical components Check for overhead obstructions All Screws, Bolts, and Pins securely fastened Surrounding area clean Operation, Maintenance and Safet
OPTIONAL EQUIPMENT INSTALLATION 25
OPTIONAL EQUIPMENT INSTALLATION Frame Cradle Pad Telescoping Screw Pad (Optional) Optional Equipment available through your Authorized BendPak Dealer.
If the lift was provided with Lift Arm Foot Guards, install the shorter Foot Guard on the shorter Arm Assembly and the longer Foot Guard on the longer Arm Assembly. To install firmly squeeze the ends of the Foot Guard inwards and insert the ends underneath the bent ends of the arm support. Release to allow the Foot Guard to spring into place. Check to be sure that Foot Guard is firmly in place. Repeat this step for each Arm Assembly Foot Guard.
STEP 17 (Operation Instructions) • Shall display the lift manufacturer’s operating instructions; ALI/SM 93-1, ALI Lifting It Right safety manual; ALI/ST-90 ALI Safety Tips card; ANSI/ALI ALOIM-2000, American National Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and Maintenance; and in the case of frame engaging lifts, ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging Lifts; in a conspicuous location in the lift area convenient to the operator.
LIFT OPERATION SAFETY (CONT’D) • ALWAYS load vehicle on lift carefully. Position the lift adapters to contact at the vehicle manufacturer’s recommended lift points. Raise lift until adapters contact vehicle. Check adapters for secure contact with vehicle. Raise lift to desired working height. (See Fig.17.1) WHEN LOWERING THE LIFT PAY CAREFUL ATTENTION THAT ALL PERSONNEL AND OBJECTS ARE KEPT CLEAR. ALWAYS KEEP A VISUAL LINE OF SITE ON THE LIFT AT ALL TIMES. ALWAYS MAKE SURE THAT ALL LOCKS ARE DISENGAGED.
Fig. 17.2 LIFT OPERATION SAFETY (CONT’D) TYPICAL LIFTING POINTS Fig. 17.3 MANY SPECIALTY OR MODIFIED VEHICLES CANNOT BE RAISED ON A TWO-POST FRAME ENGAGING LIFT. CONTACT VEHICLE MANUFACTURER FOR RAISING OR JACKING DETAILS. 4. Position vehicle for proper weight distribution arms under vehicle to allow adapters to contact at the manufacturer’s recommended pick up points. 6. Push the RAISE button or rotate the control switch on the power unit. NOTE: ALLOW (2) SECONDS BETWEEN MOTOR STARTS.
LIFT OPERATION SAFETY (CONT’D) TO LOWER THE LIFT 10. Continue to raise to desired height only if vehicle is secure on lift. 11. DO NOT go near or under a raised vehicle if all four adapters are not in secure contact with vehicle at vehicle manufacturer’s recommended lift points. WHEN LOWERING THE LIFT PAY CAREFUL ATTENTION THAT ALL PERSONNEL AND OBJECTS ARE KEPT CLEAR. ALWAYS KEEP A VISUAL LINE OF SITE ON THE LIFT AT ALL TIMES. ALWAYS MAKE SURE THAT ALL LOCKS ARE DISENGAGED.
• Always replace ALL FAULTY PARTS before lift is put back into operation. • Weekly: Check all cable connections, bolts and pins to ensure proper mounting. • Daily: Make a visual inspection of ALL MOVING PARTS and check for excessive signs of wear. • Monthly: Check equalizer cable tension. Adjust per lift installation instructions. • Daily: Check safety locks to ensure they are in good operating condition. • Monthly: Lubricate locking latch shafts.
TO RAISE LIFT t t Read operating and safety manuals before using lift. Always lift a vehicle according to the manufacturers recommended lifting points. Position vehicle between posts. Adjust swing arms so that the vehicle is positioned with the center of gravity midway between pads. Use truck adapters as needed. Never exceed 9” of pad height. NEVER use lift pad assemblies without rubber slip over pads in place. Raise the vehicle by depressing button until the vehicle just lifts off the ground.
WIRE ROPE INSPECTION AND MAINTENANCE t Lifting cables should be replaced every three - five years or when visible signs of damage are apparent. DO NOT USE LIFT WITH DEFECTIVE / WORN CABLES. t Lifting cables should be maintained in a well-lubricated condition at all times. Wire rope is only fully protected when each wire strand is lubricated both internal and external. Excessive wear will shorten the life of the wire rope.
Safe Lift Operation Automotive and truck lifts are critical to the operation and profitability of your business. The safe use of this and other lifts in your shop is critical in preventing employee injuries and damage to customer’s vehicles. By operating lifts safely you can insure that your shop is profitable, productive and safe. Safe operation of automotive lifts requires that only trained employees should be allowed to use the lift.
t DO NOT leave the controls while the lift is still in motion. t DO NOT stand directly in front of the vehicle or in the bay when vehicle is being loaded or driven into position. t DO NOT go near vehicle or attempt to work on the vehicle when being raised or lowered. t REMAIN CLEAR of lift when raising or lowering vehicle. t DO NOT rock the vehicle while on the lift or remove any heavy component from vehicle that may cause excessive weight shift.
LIFT WILL NOT RAISE POSSIBLE CAUSE 1. Air in oil, (1,2,8,13) 2. Cylinder binding, (9) 3. Cylinder leaks internally, (9) 4. Motor run backward under pressure, (11) 5. Lowering valve leaks, (3,4,6,10,11) 6. Motor runs backwards, (7,14,11) 7. Pump damaged, (10,11) 8. Pump won’t prime, (1,8,13,14,3,12,10,11) 9. Relief valve leaks, (10,11) 10. Voltage to motor incorrect, (7,14,11) REMEDY INSTRUCTION 1. Check for proper oil level. . . . . . . . . . . . . . . . . . . . . . . . . .
LIFT WILL NOT RAISE POSSIBLE CAUSE 1. Air in oil, (1,2,8,13) 2. Cylinder binding, (9) 3. Cylinder leaks internally, (9) 4. Motor run backward under pressure, (11) 5. Lowering valve leaks, (3,4,6,10,11) 6. Motor runs backwards, (7,14,11) 7. Pump damaged, (10,11) 8. Pump won’t prime, (1,8,13,14,3,12,10,11) 9. Relief valve leaks, (10,11) 10. Voltage to motor incorrect, (7,14,11) REMEDY INSTRUCTION 1. Check for proper oil level. . . . . . . . . . . . . . . . . . . . . . . . . .
MOTOR WILL NOT RUN POSSIBLE CAUSE 1. Fuse blown, (5,2,1,3,4) 2. Limit switch burned out, (1,2,3,4) 3. Microswitch burned out, (1,2,3,4) 4. Motor burned out, (1,2,3,4,6) 5. Voltage to motor incorrect, (2,1,8) REMEDY INSTRUCTION 1. Check for correct voltage . . . . . . . . . . . . . . . . . . . . . . . . . . .Compare supply voltage with voltage on motor name tag. Check that the wire is sized correctly. N.E.C. table 310-12 requires AWG 10 for 25 Amps. 2. Check motor is wired correctly . . . .
WILL NOT RAISE LOADED LIFT POSSIBLE CAUSE 1. Air in oil, (1,2,3,4) 2. Cylinder binding, (5) 3. Cylinder leaks internally, (5) 4. Lift overloaded, (6,5) 5. Lowering valve leaks, (7,8,1,5,9) 6. Motor runs backwards, (10,12,9) 7. Pump damaged, (5,9) 8. Pump won’t prime, (1,2,3,4,5,11,9) 9. Relief valve leaks, (8,5,9) 10. Voltage to motor incorrect, (10,12,5) REMEDY INSTRUCTION 1. Check oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIFT WILL NOT STAY UP POSSIBLE CAUSE 1. Air in oil, (1,2,3) 2. Check valve leaks, (6) 3. Cylinders leak internally, (7) 4. Lowering valve leaks, (4,5,1,7,6) 5. Leaking fittings, (8) REMEDY INSTRUCTION 1. Check oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The oil level should be up to the bleed screw in the reservoir with the lift all the way down. 2. Oil seal damaged and cocked . . . . . . . . . . . . . . . . . . . . . . . . Replace oil seal around pump shaft. 3.
1. 16 2 1 15 7 6 8 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING NOTE: UNLESS OTHERWISE SPECIFIED. 17 20 13 11 10 12 18 19 14 9 4 3 NEXT ASSEMBLY 5250042 5250038 5 ☺ DIMENSIONS ARE IN MM DO NOT SCALE DRAWING PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF BENDPAK INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF BENDPAK INC. IS PROHIBITED.
1. SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING NOTE: UNLESS OTHERWISE SPECIFIED. 2 3 NEXT ASSEMBLY 5260568 5260570 1 DIMENSIONS ARE IN MM ☺ DO NOT SCALE DRAWING PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF BENDPAK INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF BENDPAK INC. IS PROHIBITED.
5900952 XPR-12FDL/12FDL-LWB
A SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE ATTACHED LABEL PLACEMENT SHEET. 6 NOTE: UNLESS OTHERWISE SPECIFIED. 1. 2. 3 2 1 4 DIMENSIONS ARE IN MM ☺ PART NUMBER 5245137 5250042 5215376 5215283 5905109 5905131 5905404 5905465 5905660 5905940 5905950 DO NOT SCALE DRAWING ITEM NO 1 2 3 4 5 6 7 8 9 10 11 NAME TM 12/15/2015 PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF BENDPAK INC.
3676 155-1907.6mm [6-75"] 3015 3923 2644 DRIVE THRU 3599 343-2095.6mm [13.5-82.5"] WITH 63mm [2.5"] & 125mm [5"] ADAPTER 50 765-1473mm A SCALE: 1:45 5260568 SIZE DWG. NO. SHEET 2 OF 2 B REV XPR-12FDL PRODUCTION LIFT VER E TITLE: 1645 LEMONWOOD DR.
A SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE ATTACHED LABEL PLACEMENT SHEET. 6 NOTE: UNLESS OTHERWISE SPECIFIED. 1. 2. 3 2 1 4 PART NUMBER 5245137 5250042 5215376 5215270 5905109 5905131 5905404 5905465 5905950 5905940 5905660 DIMENSIONS ARE IN MM ☺ DO NOT SCALE DRAWING ITEM NO 1 2 3 4 5 6 7 8 9 10 11 5 TM DATE 12/16/2015 PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF BENDPAK INC.
3676 155-1907.6mm [6-75"] 3015 3923 2644 DRIVE THRU 3599 343-2095.6mm [13.5-82.5"] WITH 63mm [2.5"] & 125mm [5"] ADAPTERR 52 902-1819mm A SCALE: 1:45 5260570 SIZE DWG. NO. SHEET 2 OF 2 B REV XPR-12FDL-LWB PRODUCTION LIFT VER E TITLE: 1645 LEMONWOOD DR.
Declaration of Conformity The equipment which accompanies this declaration is in conformity with EU Directive: 2006/42/EC Machinery Directive Manufacturer BendPak Inc. 1645 Lemonwood Dr Santa Paula Ca, 93060 USA A copy of the Technical file for this equipment is available from: CCQS UK Ltd., Level 7, Westgate House, Westgate Rd., London W5 1YY UK Description of Equipment Two-Column Vehicle Service Lift XPR-12FDL XPR-12FDL-LWB 12K Cap. / Floorplate / Direct-Drive / Two-Post Lift 12K Cap.
MAINTENANCE RECORDS ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ _________
This page intentionally left blank.