IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS EUROPEAN USERS 400V 50Hz SUPPLY DETAILS ARE INCLUDED WITH ELECTRICAL CONTROL BOX. DISREGARD SUPPLY WIRING DETAILS IN THIS MANUAL PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS.
18,000; 27,000; 35,000; 40,000 POUND CAPACITY, COMMERCIAL GRADE FOUR POST AUTO / TRUCK LIFT This instruction manual has been prepared especially for you. Your new lift is the product of over 40 years of continuous research, testing and development; it is the most technically advanced lift on the market today. READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS.
OWNER’S RESPONSIBILITY IMPORTANT NOTICE To maintain the lift and user safety, the responsibility of the owner is to read and follow these instructions: Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures. Never attempt to lift components without proper lifting tools such as forklift or cranes. Stay clear of any moving parts that can fall and cause injury.
Contents TABLE OF CONTENTS Page No. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Definitions of Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Owner’s Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLER / OPERATOR PLEASE READ AND FULLY UNDERSTAND. BY PROCEEDING YOU AGREE TO THE FOLLOWING. Failure to follow danger, warning, and caution instructions may lead to serious personal injury or death to operator or bystander or damage to property. t I have visually inspected the site where the lift is to be installed and verified the concrete to be in good condition and free of cracks or other defects.
INTRODUCTION 1. Carefully remove the crating and packing materials. CAUTION! Be careful when cutting steel banding material as items may become loose and fall causing personal harm or injury. 2. Check the voltage, phase, and proper amperage requirements for the motor shown on the motor plate. Electrical work should be performed only by a certified electrician. IMPORTANT SAFETY INSTRUCTIONS Read these safety instructions entirely.
t t t t t t t TOOLS REQUIRED t t t t t t t Rotary Hammer Drill Or Similar 3/ 4” Masonry Bit Hammer 4 Foot Level Open-End Wrench Set: SAE/ Metric Socket And Ratchet Set: SAE/ Metric Hex-Key / Allen Wrench Set Large Crescent Wrench Large Wrench Crow Bar Chalk Line Medium Flat Screwdriver Tape Measure: 25 Foot Minimum Needle Nose Pliers NOTE: An air supply (30 PSI Min / 3 CFM Min.) will be required for the safety-lock mechanisms. See Step 10.
When removing the lift from shipping angles pay close attention as the posts can slide and can cause injury. Prior to removing the bolts make sure the posts are held securely by a fork lift or some other heavy lifting device.
FLOOR PLAN *IMPORTANT NOTE* Check Diagonal Measurements To Ensure Square Layout Diagonal Measurements Must Be Equal. HDS-18 HDS-18X HDS-27 HDS-27X Lifting Capacity* MODEL 18,000 lbs. / 8165 Kg. 18,000 lbs./ 8165 Kg. 27,000 lbs. / 12,247 Kg. 27,000 lbs. / 12,247 Kg. *Max Capacity / Front Axle 9,000 lbs. / 4082 Kg. 9,000 lbs. / 4082 Kg. 13,500 lbs. / 6,124 Kg. 13,500 lbs. / 6,124 Kg. *Max Capacity / Rear Axle 9,000 lbs. / 4082 Kg. 9,000 lbs. / 4082 Kg. 13,500 lbs. / 6,124 Kg. 13,500 lbs.
FLOOR PLAN *IMPORTANT NOTE* Check Diagonal Measurements To Ensure Square Layout Diagonal Measurements Must Be Equal. MODEL Lifting Capacity* HDS-35 HDS-35X HDS-40 HDS-40X 35,000 lbs. / 15,876 Kg. 35,000 lbs. / 15,876 Kg. 40,000 lbs. / 18,144 Kg. 40,000 lbs. / 18,144 Kg. *Max Capacity / Front Axle 17,500 lbs. / 7,938 Kg. 17,500 lbs. / 7,938 Kg. 20,000 lbs. / 9,072 Kg. 20,000 lbs. / 9,072 Kg. *Max Capacity / Rear Axle 17,500 lbs. / 7,938 Kg. 17,500 lbs. / 7,938 Kg. 20,000 lbs. / 9,072 Kg.
CLEARANCES HDS SUPER DUTY 54in 1372mm MINIMUM TO NEAREST BAY OR OBSTRUCTION 24in 610mm MINIMUM TO NEAREST WALL APPROACH B. Place target on floor at column positions (NOT on column base plates) and record readings. 1. Lift Location: Use architects plan and Engineers automatic level (transit) when available to locate lift. The above shows clearances of a typical bay layout. Lift floor area should be level. C. Find the highest of the four locations.
POWER UNIT LOCATION IMPORTANT NOTE ! The power unit can be located at either “ X” location shown below. It is important to locate the POWERSIDE runway (with cylinder) on the SAME SIDE as the power unit location. Utility rails on the side of each runway MUST be installed facing the center. For the remainder of this instruction the power unit will be illustrated mounted at the DRIVER-SIDE (LEFT) FRONT column - TOP ILLUSTRATION.
STEP 3 (Column & Cross Tube Installation) 1. Place a chalk line on the floor according to the floor plan layout. Pay attention to the Power Unit location. Locate and stand the Columns at their respective locations. DO NOT BOLT Columns down at this time. Use caution to prevent the Columns from falling over. (See Fig. 3.1) Fig. 3.1 Fig. 3.3 2. To estimate the shim requirements, place a target on floor at each Column position and record the readings.
2. Manually raise the Cross Tubes until the Primary Safety Locks engage and rest on the lock position second down from the top of the Ladder or approximately 66” off the ground. It is important that the SLACK SAFETY LOCK IS CLEARED. The Slack Safety Lock must never rest on the Safety Ladder. (See Fig. 4.1 -4.3) 5. The Columns and Cross Tubes will now be in position and spaced properly for the runways. 6. Install the column TOP CAPS using the M16 X 2 Hex Bolts, nuts & washers.
STEP 5 4. Position the POWERSIDE RUNWAY on top of the Cross Tubes with the UTILITY RAIL towards the center. The fitting holes located at the side of the Powerside Runway should be adjacent the POWER UNIT COLUMN. Align the holes in the Runway with the holes on the Cross Tubes and bolt together using four M18 x 2.5 hex bolts and washers. (See Fig. 5.5) (Powerside Runway Installation) 1.
WARNING! WHEN THE CABLE ADJUSTING NUTS BOTTOM OUT ON THE THREADED END OF THE CABLE CONNECTOR AND THERE IS STILL SLACK IN THE CABLES, THE CABLES HAVE STRETCHED BEYOND THE SAFE USEFUL LENGTH AND NEED TO BE REPLACED WITH FACTORY APPROVED CABLE ASSEMBLIES. DO NOT PLACE WASHERS, SPACERS OR OTHER DEVICES TO “ SHORTEN” THE EFFECTIVE CABLE LENGTH AS DAMAGE TO THE LIFT OR INJURY TO PERSONS MAY OCCUR. 1. Inspect cables to insure proper lengths. All CABLES Fig. 7.2 should have ID tags showing proper Cable lengths.
4. With the CABLES properly routed, hold the Sheaves in position and install the SHEAVE PIN. (See Fig. 7.5) Stack Cables and Sheaves in proper order and make ready for the Sheave Pin. DANGER ! DO NOT PROCEED unless visual confirmation is made of ALL Safety Locks. ALL locks MUST be engagedbefore proceeding. Failure to comply with these instructions may result in severe personal injury or death. (See page 25.) Sheave Pin Fig. 7.5 5.
7. Each cable must be installed through the CABLE RETAINER first to keep Cables stowed in their proper position on the Cable Block. (See Fig. 7.7) 9. After routing the Cables double-check to make sure all are properly positioned and REMAIN WITHIN THE GROOVES of ALL Sheaves. (See Fig. 7.10. & 7.11) Fig. 7.10 Cylinder Guide Cable Plug End Thread nut until snap ring can be installed. Cable Retainer Cable Block Fig. 7.7 8.
STEP 9 (Routing Hydraulic Hoses) NOTE: DANGER ! POWER AND RETURN PORT LOCATIONS MAY VARY. CONFIRM POWER AND RETURN PORT LOCATIONS IN POWER UNIT DOCUMENTATION OR CONTACT TECHNICAL SUPPORT. ALL WIRING MUST BE PERFORMED BY A LICENSED ELECTRICIAN. 1. Install the 90-degree Hydraulic Fitting to the POWER PORT and the 90° Air Line Compression Fitting to the RETURN PORT of the Power Unit and connect the Hoses as described below.
6. Install the end of Flex Hose with the Straight Fitting on the Hydraulic Hose into the hole in the Powerside Runway adjacent to the Power Unit. Install the end of the Flex Hose with the 90° Fitting on the Hydraulic Hose in the Flex Hose Bracket Assy. Tighten the plastic nuts securely. (See Fig 9.7) Fig. 9.7 Fig. 9.3 3. Install the 90° Hydraulic Fittings in the port at the ram end of the cylinder. On the pipe thread side of the fitting it is recommended to use Teflon tape or pipe sealer.
STEP 10 ( Routing Air Lines) 1. Mount the Push Button Air Valve Assembly on to the power unit mounting bracket. The Push Button Air Valve should be positioned away from the Power Side Ramp on the “out” side of the lift for operator safety. (See Fig 10.1) Fig. 10.1 Air Supply In Push Button Air Valve Assembly 2. Route the air line that was left unconnected in Step 10 to the 90° Air Line Compression Fitting of the Push Button Air Valve Assembly. (See Fig 10.2) Fig. 10.2 To Flex Hose 3.
SAFETY AIR LINE ROUTING NOTE: CUT THE PROVIDED 1/4” AIR LINE TUBING WITH A SHARP BLADE TO LENGTHS AS REQUIRED. TUBING MUST BE CUT SQUARE WITH ALL PLASTIC BURRS REMOVED. AIR TUBING ASSEMBLY: SEE PAGE 20 FOR ASSEMBLY OF AIR LINE TUBING INTO FITTING. CAUTION: REMOVING THE AIR TUBING FROM THE COMPRESSION FITTINGS WILL CAUSE DAMAGE TO THE TUBING ITSELF. USE OF A DAMAGED AIR LINE MAY RESULT IN SAFETY LOCK FAILURE.
DANGER! DO NOT PERFORM ANY MAINTENANCE OR INSTALLATION OF ANY COMPONENTS WITH OUT FIRST ENSURING THAT ELECTRICAL POWER HAS BEEN DISCONNECTED AT THE SOURCE OR PANEL AND CANNOT BE RE-ENERGIZED UNTIL ALL MAINTENANCE AND/OR INSTALLATION PROCEDURES ARE COMPLETED. IMPORTANT POWER-UNIT INSTALLATION NOTES n DO NOT run power unit with no oil. Damage to pump can occur. n The power unit must be kept dry. Damage to power unit caused by water or other liquids such as detergents, acid etc.
STEP 12 STEP 11 (Installing The Slack Safety Springs) (Power Unit Hook Up) 1. Have a CERTIFIED ELECTRICIAN run the power supply to motor. Refer to the data plate found on the motor for proper power supply and wire size. The following steps involve the SLACK CABLE SAFETY DEVICE and MAIN SAFETY. Failure to follow these steps could result in serious injury or death in the event of cable failure. 1. Install the unattached end of the ALL SAFETY LOCK SPRINGS as shown.
5. Check to make sure that all Slack Safety locks are cleared and free. (See Fig. 13.1) KEEP HANDS AND FEET CLEAR. Remove hands and feet from any moving parts. Keep feet clear of lift when lowering. Avoid pinch points. 9. Check all MAIN SAFETY LOCKS to make sure they move freely and spring back to the lock position when released. Lubricate all SAFETY PIVOT points with WD-40 or equal. 10.
STEP 15 3. After drilling, REMOVE DUST thoroughly from each hole using compressed air and/ or bristle brush. Make certain that the Columns remain aligned with the chalk line. (Final Assembly) 1. Install the approach ramps on the entry side of the lift. (See Fig. 15.1 &15.2) Fig. 15.1 ALWAYS WEAR SAFETY GOGGLES. 4. Assemble the washersand nuts on the anchors then tap into each hole with a sledge until the washer rests against the base plate.
5. Beginning with “ A” position, sight the level to the target and mark the number or the graduation on the inch scale of the target that aligns to the cross hairs of the Level, (See Fig. 16.1) Note: Use a pencil, marking pen or attach a paper clip onto the target scale at the cross hair reference. 12. Raise the lift to full height. Listen and watch as the locking latches click in place. SYNCHRONIZE BY ADJUSTING THE CABLES so that all four latches click at the same time.
OPTIONAL EQUIPMENT INSTALLATION Rolling Jack maximum weight capacity for use with HDS-18 or HDS-18X is 9,000 lb (4,082 kg) per unit HDS-27 or HDS-27X is 13,500 lb (6,124 kg) per unit HDS-35 or HDS-35X is 17,500 lb (7,938 kg) per unit 5174010 Part # 5550502 5550503 5550504 5570784 5570725 HD/ HDS-18; 27; 35 AIR LINE KIT Description 5174011 HD/ HDS-18X; 27X; 35X AIR LINE KIT Qty.
OPTIONAL EQUIPMENT INSTALLATION 30
STEP 19 • Shall display the lift manufacturer’s operating instructions; ALI/SM 93-1, ALI Lifting It Right safety manual; ALI/ST-90 ALI Safety Tips card; ANSI/ALI ALOIM-2000, American National Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and Maintenance; and in the case of frame engaging lifts, ALI/ LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging Lifts; in a conspicuous location in the lift area convenient to the operator.
LIFT OPERATION SAFETY (CONT’D) • ALWAYS keep area around lift free of tools, debris, grease and oil. • NEVER overload lift. Capacity of lift is shown on nameplate affixed to the lift. DANGER! VISUALLY CONFIRM THAT ALL PRIMARY SAFETY LOCKS ARE ENGAGED BEFORE ENTERING WORK AREA. SUSPENSION COMPONENTS USED ON THIS LIFT ARE INTENDED TO RAISE AND LOWER LIFT ONLY AND ARE NOT MEANT TO BE LOAD HOLDING DEVICES.
LIFT OPERATION SAFETY (CONT’D) 3. Press the push button air safety valve and HOLD. • Every 3 Months: Check anchor bolt torque. Anchors should be torqued to 90 ft/lbs. 4. Push the LOWERING HANDLE on the Power Unit until the lift has descended completely. • Semi-Annually: Check fluid level of lift power unit and refill if required per lift installation instructions. • Replace all caution, warning or safety related decals on the lift if unable to read or missing. Reorder labels from BendPak.
WIRE ROPE INSPECTION AND MAINTENANCE t Lifting cables should be replaced every three - five years or when visible signs of damage are apparent. DO NOT USE LIFT WITH DEFECTIVE / WORN CABLES. t Lifting cables should be maintained in a well-lubricated condition at all times. Wire rope is only fully protected when each wire strand is lubricated both internal and external. Excessive wear will shorten the life of the wire rope.
Safe Lift Operation Automotive and truck lifts are critical to the operation and profitability of your business. The safe use of this and other lifts in your shop is critical in preventing employee injuries and damage to customer’s vehicles. By operating lifts safely you can insure that your shop is profitable, productive and safe. Safe operation of automotive lifts requires that only trained employees should be allowed to use the lift.
t Pay attention when walking under a vehicle that is up on the hydraulic lift t DO NOT Leave the controls while the lift is still in motion. t DO NOT stand directly in front of the vehicle or in the bay when vehicle is being loaded or driven into position. t DO NOT Go near vehicle or attempt to work on the vehicle when being raised or lowered. REMAIN CLEAR of lift when raising or lowering vehicle.
LIFT WILL NOT RAISE POSSIBLE CAUSE 1. Air in oil, (1,2,8,13) 2. Cylinder binding, (9) 3. Cylinder leaks internally, (9) 4. Motor run backward under pressure, (11) 5. Lowering valve leaks, (3,4,6,10,11) 6. Motor runs backwards, (7,14,11) 7. Pump damaged, (10,11) 8. Pump won’t prime, (1,8,13,14,3,12,10,11) 9. Relief valve leaks, (10,11) 10. Voltage to motor incorrect, (7,14,11) REMEDY INSTRUCTION 1.
MOTOR WILL NOT RUN POSSIBLE CAUSE 1. Fuse blown, (5,2,1,3,4) 2. Limit switch burned out, (1,2,3,4) 3. Microswitch burned out, (1,2,3,4) 4. Motor burned out, (1,2,3,4,6) 5. Voltage to motor incorrect, (2,1,8) REMEDY INSTRUCTION 1. Check for correct voltage Compare supply voltage with voltage on motor name tag. Check that the wire is sized correctly. N.E.C. table 310-12 requires AWG 10 for 25 Amps. 2.
WILL NOT RAISE LOADED LIFT POSSIBLE CAUSE 1. Air in oil, (1,2,3,4) 2. Cylinder binding, (5) 3. Cylinder leaks internally, (5) 4. Lift overloaded, (6,5) 5. Lowering valve leaks, (7,8,1,5,9) 6. Motor runs backwards, (10,12,9) 7. Pump damaged, (5,9) 8. Pump won’t prime, (1,2,3,4,5,11,9) 9. Relief valve leaks, (8,5,9) 10. Voltage to motor incorrect, (10,12,5) REMEDY INSTRUCTION 1. Check oil level The oil level should be up to the bleed screw in the reservoir with the lift all the way down.
LIFT WILL NOT STAY UP POSSIBLE CAUSE 1. Air in oil, (1,2,3) 2. Check valve leaks, (6) 3. Cylinders leak internally, (7) 4. Lowering valve leaks, (4,5,1,7,6) 5. Leaking fittings, (8) REMEDY INSTRUCTION 1. Check oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The oil level should be up to the bleed screw in the reservoir with the lift all the way down. 2. Oil seal damaged and cocked . . . . . . . . . . . . . . . . . . . . . . . . Replace oil seal around pump shaft. 3.
Grease Port / Lubrication Locations Lubricate Once A Week Torque Recommendations VALUES ARE STATED IN FOOT POUNDS (ft-lb) SAE 0-1-2 SAE Grade 5 SAE Grade 8 SOCKET HEAD CAP SCREW CLASS 4.8 CLASS 8.8 CLASS 10.9 CLASS 12.9 Bolt Size (SAE) Bolt Size (Metric) 1/4-20 M6 x 1.0 6 10 14 13 5/16-18 M8 x 1.25 12 19 29 31.4 3/8-16 M10 x 1.50 62 7/16-14 20 33 47 32 54 78 1/2-13 M12 x 1.75 47 78 119 108 9/16-12 M14 x 2.00 69 114 169 173 5/8-11 M16 x 2.
MAINTENANCE RECORDS ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ ____________________________________________________________________ _________
1. 2. 5 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING FASTEN NUTS AND WASHERS TO SAFETY LADDERS IN ORDER SHOWN FOR SHIPMENT 1 NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. 3. 4. 5. 6. 21 23 20 24 19 22 13 7. B 30 27 25 29 28 26 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT THREAD 5535104 WITH 5545415 ONTO CABLES FOR SHIPMENT HOSES AND CABLES IN REPRESENTATIONAL FORM (*) LENGTH FOR REFERENCE ONLY ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE RECEIVED LIFT FOR PLACEMENT 5930605 TO BE ADDED BY REQUEST ONLY NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING FASTEN NUTS AND WASHERS TO SAFETY LADDERS IN ORDER SHOWN FOR SHIPMENT 2 NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. 3. 4. 5. 6. 20 31 21 23 25 7. 29 13 30 9 8 28 26 27 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT THREAD 5535104 WITH 5545415 ONTO CABLES FOR SHIPMENT HOSES AND CABLES IN REPRESENTATIONAL FORM (*) LENGTH FOR REFERENCE ONLY ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE RECEIVED LIFT FOR PLACEMENT 5930605 TO BE ADDED BY REQUEST ONLY NOTE: UNLESS OTHERWISE SPECIFIED.
SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING FASTEN NUTS AND WASHERS TO SAFETY LADDERS IN ORDER SHOWN FOR SHIPMENT 3 NOTE: UNLESS OTHERWISE SPECIFIED. 1. 2.
1. 2. 3. 4. 5. 6. 21 23 24 20 22 19 B 7. 30 27 25 26 13 29 DETAIL B SCALE 1 : 12 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT THREAD 5535104 WITH 5545415 ONTO CABLES FOR SHIPMENT HOSES AND CABLES IN REPRESENTATIONAL FORM (*) LENGTH FOR REFERENCE ONLY ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE RECEIVED LIFT FOR PLACEMENT 5930605 AND 5215637 TO BE ADDED BY REQUEST ONLY NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING FASTEN NUTS AND WASHERS TO SAFETY LADDERS IN ORDER SHOWN FOR SHIPMENT 5 NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. 3. 4. 5. 6. 24 20 29 25 23 22 7. 9 5 30 2 28 26 27 19 16 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT THREAD 5535104 WITH 5545415 ONTO CABLES FOR SHIPMENT HOSE S AND CABLES IN REPRESENTATIONAL FORM (*) LENGTH FOR REFERENCE ONLY ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE RECEIVED LIFT FOR PLACEMENT 5930605 TO BE ADDED BY REQUEST ONLY NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. 5 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING FASTEN NUTS AND WASHERS TO SAFETY LADDERS IN ORDER SHOWN FOR SHIPMENT 1 NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. 3. 4. 5. 6. 23 21 20 25 26 19 11 7. 7 29 30 4 6 28 27 12 3 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT THREAD 5535055 WITH 5545032 ONTO CABLES FOR SHIPMENT HOSES AND CABLES IN REPRESENTATIONAL FORM (*) LENGTH FOR REFERENCE ONLY ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE RECEIVED LIFT FOR PLACEMENT 5930605 TO BE ADDED BY REQUEST ONLY NOTE: UNLESS OTHERWISE SPECIFIED.
1. 2. 6 1 3 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING FASTEN NUTS AND WASHERS TO SAFETY LADDERS IN ORDER SHOWN FOR SHIPMENT NOTE: UNLESS OTHERWISE SPECIFIED.
21 19 29 28 26 4 7. 1. 2. 3. 4. 5. 6. 7 27 25 30 17 18 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING INSERT PARTS BAG INTO PARTS BOX FOR SHIPMENT THREAD 5535055 WITH 5545032 ONTO CABLES FOR SHIPMENT HOSES AND CABLES IN REPRESENTATIONAL FORM (*) LENGTH FOR REFERENCE ONLY ALL LABELS TO BE APPLIED TO POSTS AFTER PAINTING. SEE RECEIVED LIFT FOR PLACEMENT 5930605 TO BE ADDED BY REQUEST ONLY 22 11 5 NOTE: UNLESS OTHERWISE SPECIFIED.
1. 10 9 DETAIL D SCALE 1 : 10 DETAIL A SCALE 1 : 5 6 12 21 5 DETAIL E SCALE 1 : 5 SEE SHIPPING INSTRUCTIONS FOR FINAL PACKAGING NOTE: UNLESS OTHERWISE SPECIFIED. 13 17 22 3 2 15 14 16 NEXT ASSEMBLY 5250159 5250162 5250170 5250172 5250175 5250177 5250179 DETAIL F SCALE 1 : 2 1 ☺ DI MENSI ONS ARE IN MM SIZE: ----- 19 AC NAME DATE 05/06/2009 PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF BENDPAK INC.
For Parts Or Service Contact: BendPak Inc. / Ranger Products 1645 Lemonwood Dr. Santa Paula, CA. 93060 Tel: 1-805-933-9970 Toll Free: 1-800-253-2363 Fax: 1-805-933-9160 www.bendpak.
