Use and Care Manual
Table Of Contents
- Table of Contents
- Introduction
- Shipping Information
- Safety Considerations
- Components
- Specifications
- Installation Checklist
- Installation
- Reviewing the Safety Rules
- Gathering Your Tools
- Preparing for Electrical Work
- Reviewing the Installation Orientation
- Checking Clearances
- Selecting a Location
- Choosing a Wide or Narrow Configuration
- Installing the Safety Assemblies and Positioning the Safety Lock Cable
- Putting the Equalizing Cables into Position
- About Thread Sealants
- Identifying Hydraulic Fittings
- Routing the Hydraulic Hoses
- Creating Chalk Line Guides
- Anchoring the Posts
- Installing the Overhead Assembly and Safety Shutoff Bar
- Installing the Microswitch
- Completing the Equalizing Cables Installation
- Mounting the Power Unit
- Installing the Safety Lock Cable
- Connecting the Hydraulic Hoses
- Installing the Lift Arms
- Double Threaded Rod Installation
- Leveling
- Contact the Electrician
- Electrical Information
- Wiring the Microswitch
- Connecting the Power Unit
- Installing a Power Disconnect Switch
- Installing a Thermal Disconnect Switch
- Lubricating the Lift
- Review Final Checklist Before Operation
- Leave the Manual with the Owner/Operator
- Perform an Operational Test
- Operation
- Maintenance
- Troubleshooting
- Wiring Diagrams
- Labels
- Parts Drawings
- Automotive Lift Institute (ALI) Store
- Maintenance Log
- Maintenance Log
Manual. 10AP Series Two-Post Lifts, Installation and Operation Manual, Manual Part Number 5900265, Manual
Revision A10, released September 2023.
Copyright. Copyright ©2023 by BendPak Inc. All rights reserved. You may make copies of this document if you
agree that: full attribution goes to BendPak Inc., you are not authorized to make changes to the content, you do
not gain any rights to this content, and you will not use the copies for commercial purposes.
Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,
product, and service names are used for identification only. All trademarks and registered trademarks mentioned
in this manual are the property of their respective owners.
Limitations. Every effort has been made to ensure complete and accurate instructions are
included in this manual. However, product updates, revisions, and/or changes may have
occurred since this manual was published. BendPak reserves the right to change any
information in this manual without incurring any obligation for equipment previously or
subsequently sold. All drawings are reference only – do not scale. BendPak is not responsible
for typographical errors in this manual. You can always find the latest version of the manual
for your product on the BendPak website.
Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment
to the value of your new product. Contact your nearest BendPak dealer or visit
www.bendpak.com/support/warranty for full warranty details. Go to bendpak.com/support/register-
your-product/ and fill out the online form to register your product (be sure to click Submit).
Safety. Your Lift was designed and manufactured with safety in mind. Your safety also depends on proper
training and thoughtful operation. Do not set up, operate, maintain, or repair the Lift without reading and
understanding this manual and the labels on the unit; do not use your Lift unless you can do so safely!
Owner Responsibility. In order to maintain your product properly and to ensure operator safety, it is the
responsibility of the product owner to read and follow these instructions:
• Follow all installation, operation, and maintenance instructions.
• Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,
such as state and federal OSHA regulations and electrical codes.
• Read and follow all safety instructions. Keep them readily available for operators.
• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.
• Do not operate the product until you are certain all parts are in place and operating correctly.
• Carefully inspect the product on a regular basis and perform all maintenance as required.
• Service and maintain the unit only with approved replacement parts.
• Keep the manual with the product and make sure all labels are clean and visible.
• BendPak makes no promises, guarantees or assurances that our products meet any state, county, federal or
international mandated permit, license, code, standard, certification, or any other mandate other than what is
listed or shown on BendPak website(s), or any BendPak or Ranger online or published catalog. Not all
BendPak Lift models meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201.
Consult www.autolift.org for a complete list of Lift models that meet ANSI/ALI ALCTV-(current edition) or
ANSI/UL 201, or contact BendPak via contact@bendpak.com. Buyer assumes full responsibility
for any state, county, federal or international mandated permit, license, code, standard,
certification, or any other mandate required related to the installation and/or operation of
any BendPak product. BendPak will not be responsible for any charges, fines, liens, or other levies
imposed on the Buyer related to any special or regional structural, seismic or any other building code and/or
codes such as the Uniform Building Code (UBC), International Building Code (IBC), or any other state, county,
federal or international mandated permit, license, code, standard, certification, or other mandate, law, rule,
regulation or directive by any other agency, government, administrations, or corporations whether state,
county, federal, or international mandated.
Only use the Lift if it can be used safely!
SCAN FOR
DIGITIAL PDF