Specifications

7
FIGURE 11 - CORRECT GROOVE CLEARANCE
PISTON RING OIL RING
.001”
.003”
.002”
.004”
CORRECT GAP CLEARANCE
WITH RINGS IN CYLINDER
.002”
.010”
EXPANDER RING
OIL RING
PISTON RING
On compressors fitted with precision, sleeve main bearings,
the difference between the O.D. of the crankshaft journal
and the main bearing I.D. must not exceed .0065 in. If the
clearance is greater than .0065 in., the end cover or main
bearing must be replaced.
Check the unloader bore bushings to be sure they are not
worn, rusted, or damaged. If these bushings are to be
replaced, they can be removed by running a 1/8 in. pipe
thread tap into the bushing, and inserting a 1/8 in. pipe
threaded rod and pulling the bushing straight up and out.
Do not use an easy-out for removing these bushings. If the
inlet valve seats are worn or damaged, so they cannot be
reclaimed by facing, they should be replaced. Cylinder
bores should be checked with inside micrometers or
calipers. (Fig. 10). Cylinder bores which are scored or out of
round by more than .001 in. or tapered more than .002 in.
should be rebored or honed oversize. Oversized pistons and
piston rings are available in .010 in., .020 in. and .030 in.
oversizes. Cylinder bores must be smooth, straight, and
round. Clearance between the cast iron pistons and cylinder
bores should be between .002 in. minimum and .004 in.
maximum.
Pistons
Check the pistons for scores, cracks, or enlarged ring
grooves; replace the pistons if any of these conditions are
found. Measure each piston with a micrometer in relation
to the cylinder bore diameter to be sure the diametral
clearance is between .002 in. minimum and .004 in.
maximum.
Check the fit of the wrist pins to the pistons and connecting
rod bushings. The wrist pin should be a light press fit in the
piston. If the wrist pin is a loose fit, the piston and pin
assembly should be replaced. Check the fit of the wrist pin
in the connecting rod bushing by rocking the piston. This
clearance should not exceed .0007 in. Replace the wrist
pin bushings if excessive clearance is found. Wrist pin
bushings should be reamed to between .5314 in. and .5317
in. after being pressed into the connecting rods.
Check the fit of the piston rings in the piston ring grooves.
Check the ring gap with the rings installed in the cylinder
bores. Refer to Fig. 11 for correct gap and groove clearances.
Crankshaft
Check the crankshaft threads, keyways, tapered ends and
all machined and ground surfaces for wear, scores, or
damage. Standard crankshaft journals are 1.1250 in.
1.1242in. in diameter. If the crankshaft journals are
excessively scored or worn or out of round and cannot be
reground, the crankshaft must be replaced. Connecting
rod bearing inserts are available in .010 in., .020 in. and
.030 in. undersizes for compressors with reground
crankshafts. Main bearing journals must be maintained so
the ball bearings are a snug fit or so that no more than
.0065 in. clearance exists between the precision sleeve
main bearing and the main bearing journals on the
crankshaft. In crankshafts fitted with oil seal rings, the oil
seal ring groove or grooves must not be worn. The ring
groove walls must have a good finish and they must be
square. Check to be sure the oil passages are open through
the crankshaft.
Connecting Rod Bearings
Used bearing inserts must be replaced. Connecting rod
caps are not interchangeable. The locking slots of the
connecting rod and cap should be positioned adjacent to
each other. Clearance between the connecting journal and
the connecting rod bearing must not be less than .0003 in.
or more than .0021 in. after rebuilding.
REPAIRS
Discharge Valves, Valve Stops and Seats
If the discharge valve seats merely show signs of slight
wear, they can be dressed by using a lapping stone, grinding
compound and grinding tool. If the discharge valve stops
are to be replaced, an application of a sealer is required,
such as “Locktite Retaining Compound #75.” Be sure that
the press fit between the discharge valve stop outside
diameter and the valve stop bore in the cylinder head is a
minimum of .0008 in. and a maximum of .0028 in. If this fit
can not be maintained, a new cylinder head body must be
used. Be sure to completely support the outside top of the
cylinder head casting, while pressing in the replacement
stops. Install the new discharge valve springs and valves.
Screw in the discharge valve seats. Discharge valve travel
should be between .041 in. to .057 in.
To test for leakage by the discharge valves, apply 100 pounds
of air pressure through the cylinder head discharge port
and apply a soap solution to the discharge valves and seats.
A slight leakage in the form of soap bubbles is permissible.
If excessive leakage is found, leave the air pressure applied
and with the use of a fibre or hardwood dowel and a hammer,
tap the discharge valves off their seats several times. This
will help the valves to seat and should reduce the leakage.
With the air pressure still applied at the discharge port of