User's Manual

16
Diagnostic Trouble Codes (DTCs) (continued)
1st
Digit
2nd
Digit
Diagnostic
Code
Description
Possible Causes / Repair Information
J1587
(SID/
FMI)
J1939
(SPN/
FMI)
11 2
TABS‑6
Advanced
AuxiliaryI/O
Error:
AUXI/O#1
•Checkforcorroded/damagedwiringorconnectorsbetweentheECUand
the auxiliary device.
•CheckPinsX1-14&X1-15oftheECU‘Power’connectorforthe
following:
‑ Pins not pushed back.
-Correctlywiredtotheauxiliarydevice(PinX1-14tosupply,PinX1-15to
ground).
-Shortedtoground,VbatorotherECUpins.
• Verify the auxiliary device is properly functioning and rated for maximum
loadof≤2amps.
• After repairs or if no issues are found, then clear the diagnostic codes.
•Ifdiagnosticcodepersists,contacttheBCVSlocalrepresentativebefore
replacing the TABS‑6 Advanced module.
152/12 612/12
11 3
TABS‑6
Advanced
AuxiliaryI/O
Error:
AUXI/O#2
•Checkforcorroded/damagedwiringorconnectorsbetweentheECUand
the auxiliary device.
•CheckPinsX1-8&X1-15oftheECU‘Power’connectorforthefollowing:
‑ Pins not pushed back.
-Correctlywiredtotheauxiliarydevice(PinX1-8–supply,
PinX1-15–ground).
-Shortedtoground,VbatorotherECUpins.
• Verify the auxiliary device is properly functioning and rated for maximum
loadof≤2amps.
• After repairs or if no issues are found, then clear the diagnostic codes.
•Ifdiagnosticcodepersists,contacttheBCVSlocalrepresentativebefore
replacing the TABS‑6 Advanced module.
152/12 612/12
11 4
TABS‑6
Advanced
AuxiliaryI/O
Error:
AUXI/O#4
•Checkforcorroded/damagedwiringorconnectorsbetweentheECUand
the auxiliary device.
•CheckPinX1-3oftheECU‘Power’connectorforthefollowing:
‑ Pin not pushed back.
-Correctlywiredtotheauxiliarydevice(PinX1-3–supply).
-Shortedtoground,VbatorotherECUpins.
• Verify the auxiliary device is properly functioning and rated for maximum
loadof≤1.5amps.
• After repairs or if no issues are found, then clear the diagnostic codes.
•Ifdiagnosticcodepersists,contacttheBCVSlocalrepresentativebefore
replacing the TABS‑6 Advanced module.
152/12 612/12
11 5
TABS‑6
Advanced
AuxiliaryI/O
Error:
AUXI/O#6
•Checkforcorroded/damagedwiringorconnectorsbetweentheECUand
the auxiliary device.
•CheckPinsX1-2&X1-13oftheECU‘Power’connectorforthefollowing:
‑ Pins not pushed back.
-Correctlywiredtotheauxiliarydevice(PinX1-2–supply,
PinX1-13–ground).
-Shortedtoground,VbatorotherECUpins.
• Verify the auxiliary device is properly functioning and rated for maximum
loadof≤1.5amps.
• After repairs or if no issues are found, then clear the diagnostic codes.
•Ifdiagnosticcodepersists,contacttheBCVSlocalrepresentativebefore
replacing the TABS‑6 Advanced module.
152/12 612/12