User's Manual

15
Diagnostic Trouble Codes (DTCs) (continued)
1st
Digit
2nd
Digit
Diagnostic
Code
Description
Possible Causes / Repair Information
J1587
(SID/
FMI)
J1939
(SPN/
FMI)
Trailer System Braking
9 1
ExtendedBrake
Application
Detected
• Verify that there is no residual pressure in the trailer’s control (service)
line.
• After repairs or if no issues are found, then clear the diagnostic codes.
• If diagnostic code persists:
‑ ContacttheBCVSlocalrepresentativebeforereplacingtheTABS-6
Advanced module.
057/07 1047/07
9 2
ExcessiveABS
ActivityDetected
DynamicWheelSpeedSensorDTC-possibleincorrectwheelspeed
signal while vehicle in motion resulted in long ABS event.
GotoSectionEonPage31.
057/07 1047/07
9 3
ExcessiveTRSP
ActivityDetected
•Cleardiagnosticcodes.
• If diagnostic code persists:
‑ ContacttheBCVSlocalrepresentativebeforereplacingtheTABS-6
Advanced module.
057/07 1047/07
TABS‑6 Advanced Module (TABS‑6 Adv)
10 1
TABS‑6
Advanced
InternalError
•Checkfordamagedorcorrodedconnectors.
•Checkfordamagedwiring.
• After repairs or if no issues are found, then clear the diagnostic codes.
• If diagnostic code persists:
‑ ContacttheBCVSlocalrepresentativebeforereplacingtheTABS-6
Advanced module.
254/12 629/12
10 2
TABS‑6
Advanced
Conguration
Error
•VerifytheECUparametersandactualsysteminstallationiscompatible
using the Bendix
®
ACom
®
DiagnosticSoftware(version6.1orhigher).
•Re-programECUasnecessary.
•Ifnecessary,contacttheBCVSlocalrepresentativetoobtainthecorrect
congurationdata.
254/13 629/13
10 3
TABS‑6
Advanced
EEPROMError
•VerifytheECUparametersandactualsysteminstallationiscompatible
using the Bendix
®
ACom
®
DiagnosticSoftware(version6.1orhigher).
•Re-programECUasnecessary.
•Ifnecessary,contacttheBCVSlocalrepresentativetoobtainthecorrect
congurationdata.
254/13 629/13
10 4
TABS‑6
AdvancedNot
Congured
•Re-programtheECUtobecompatibletotheactualsystemconguration
using the Bendix
®
ACom
®
DiagnosticSoftware(version6.1orhigher).
•Ifnecessary,contacttheBCVSlocalrepresentativetoobtainthecorrect
congurationdata.
254/13 629/13
10 5
TABS‑6
Advanced
EOLTestNot
Completed
• Perform the Installation Test using the Bendix
®
ACom
®
Diagnostic
Software (version 6.1 or higher), or Trailer Information Module.
254/14 629/14
AuxiliaryDesignLanguage(ADL)&AuxiliaryI/O’s
11 1
TABS‑6
Advanced
AuxiliaryI/O
Error:
AUXI/O#7
(Trailer ABS
IndicatorLamp)
•Checkforcorroded/damagedwiringorconnectorsbetweentheECUand
theABSIndicatorLamp.
•CheckPinX1-5oftheECU‘Power’connectorforthefollowing:
‑ Pin not pushed back.
-CorrectlywiredtotheABSIndicatorLamp(PinX1-5–supply).
-Shortedtoground,VbatorotherECUpins.
•VerifytheABSIndicatorLampisproperlygroundedandnotburntout.
• After repairs or if no issues are found, then clear the diagnostic codes.
•Ifdiagnosticcodepersists,contacttheBCVSlocalrepresentativebefore
replacing the TABS‑6 Advanced module.
152/12 612/12