SB9011D All-in-one Touch POS Terminal USER MANUAL
Table of Contents 1 Overview ............................................................................................ 2 1.1 1.2 Safety Information ........................................................................................ 2 Electromagnetic compatibility statement ................................................. 3 2 Installation Guide ............................................................................. 4 2.1 2.2 Appearances.....................................................
1 Overview Thank you for purchasing the SB9011D all-in-one touch POS terminal, Bematech is committed to continuously improve product quality and provide better after-sales service. In order to take full advantage of our devices, we strongly recommend that you take the time to read this manual before diving into software solution. Note: Information in this manual may change without prior notice. 1.
monitor screen. Wipe it clean with a soft terry cloth applied with a mild solution Do not share the same power outlet with high-power electrical appliances; keep distance from high level magnetic interference. Do not the use sharp pointed objects to work with the touch screen to avoid damage to the screen.
2 Installation Guide 2.
2.2 Rear panel I/O connectors At the rear panel of the SB9011D is a row of external I/O device connectors detailed as follows: POWER key: Turn power on/off MOUSE: Connection to PS/2 mouse KB: Connection to PS/2 keyboard LPT: DB25 parallel port for connection to POS printer VGA: VGA signal output for connection to external monitor COM 1.3.4.5.
3 Setup and Driver Installation 3.1 Motherboard BIOS settings The POS terminal has a BIOS (Basic Input Output System) chip on the motherboard. Every time you start the terminals, the system will first run the BIOS self-test routine to check the main components of the system to ensure it is working properly. The terminal is loaded with default BIOS settings in the factory. Please do not change the parameters in the BIOS unless necessary.
Main CMOS Setup Menu System Overview IP25X2 BIOS VER:1.00 AMIBIOS Version :08.00.15 Built Date:06/20/11 ID:LIPVB8106 System summary IDE Device CF Disk Device SATA1 Device SATA2 Device System time (hh:mm:ss) System date (mm:dd:yy) Language System Overview IP25X2 BIOS VER:1.00 AMIBIOS Version :08.00.15 Item Help 2011-06-20 Not detected Not detected Hard Disk Not Detected While entering setup BIOS auto detects the Presence of SATA Device. This displays The status of auto detection of SATA devices.
Exit Menu Exit options Item Help Save Change and Exit Discard Change and Exit Discard Change Exit system setup after saving the changes. Load Optimal Default F1 Help Esc Exit ↑↓ Select Item +/- Change Values ←→ Select Menu Enter Select Sub Menu F9 Setup Defaults F10 Save and Exit 3.2 Touch screen driver installation: Step 1: Navigate to the installer directory to find the setup.exe file. Double-click on “setup.exe” to start installation.
Step 2: When installation starts, click [Next] to proceed to the next step.
Step 4: Uncheck “Install PS/2 interface driver” and click [Next] to continue installation. Step 5: Uncheck “install RS232 interface driver” and click [Next] to continue installation.
Step 6: Select option “NONE”, click [Next] to continue installation.
Step 8: If there are additional touch monitors connected, please check “Support multi- monitor system”. Step 9: Select the destination location to install the touch driver. The default path is “C: \ Program Files \ eGalaxtouch”. Click [Next] to continue installation.
Step 10: Select the Program Folder to install the utility. “eGalaxtouch”. Click [Next] to continue installation. Step 11: Check the option to create a desktop shortcut icon.
After install the driver successfully, identify the USB controller is installed as shown below.
Touch calibration Touch device line test 15
4 Troubleshooting 1) Terminal does not boot If the terminal cannot boot after repeated pressing of the power switch when connect to the power, the terminal power light remains off, the fan does not operate, and the BIOS beeping is not heard, it might be power supply problems. (a) Check the power adapter is plugged in correctly to the power outlet. (b) Check the connection between the terminal and the power adapter, and then re-boot the machine.
the hardware and reboot; (e) If the above steps do not resolve this problem, reinstall the operating system. 3) The touch screen does not respond (a) Remove the touch driver and then install it again. (b) Execute the “eGalaxTouch utility and check if the interface port is working. 4) When touching the screen, cursor always returns to a fixed position. (a) Check if there is anything pressing on the touch screen. (b) Other high power or high frequency equipment may affect the screen or controller.
8) The cursor in the touch screen can only move in a small area or touch positions are inaccurate. (a) This situation usually occurs first time after installing the driver. Please run the touch screen calibration program. We also recommend you to do this after changing monitor resolution. (b) Run the touch screen calibration program to do a 25-point recalibration.
5 Specifications MODEL SB9011D 15” All-in-one Touch POS Terminal Main Board CPU Intel Atom Processor, D525 dual core 1.8GHz Chipset D525 + CH8M chipset Memory DDR3 1066/1333, up to 4GB Storage SATA 2.
SB9011D All-in-one Touch POS terminal 20
