Datasheet

ManualsBrandsBeltrona ManualsAccus & BatteriesSC3000 Non-standard battery (rechargeable) Sub-C Z solder tab NiMH 1.2 V 3000 mAh

del and specification without prior notice

℃

Time (days)

(Type)

：LP43SC3000P

Specifications of single cell

Note:

Nominal capacity, rated at 0.2C 20℃.

Average capacity, for reference only.

Weight and internal impedance are For reference.

Nominal voltage

1.2V

Capacity

0.2C Discharge

Minimum

300min

Typical

315min

Dimensions

Diameter

22.5

-0.7

Height

43.0

-1.0

Weight(Approximately)

gram

Internal Impedance At 1000 Hz

10m



(Max)

After Charge）

Charge

Standard

300mA(0.1C)

16hrs

Rapid

600mA(0.2C)

6.0hrs

Ambient

temperature

Charge

standard

℃

0℃ to 40℃

Rapid 0℃ to 40℃

Discharge

-20

℃

to 50

℃

Storage

-20

℃

to 50

℃

Number of cycles life curve

Nominal capacity (%)

Cycle life characteristics

℃

charge time (hours)

Charge: 0.1C

16hrs.

Typical characteristics

Standard charge

characteristics

PVC (Dimensions with tube)

(mm)

Charge retention curves of Ni-MH cylindrical cell At

various storage temperature

Capacity Reserve (%)

Rapid charge

Charge: 0.2C

6.0hrs.

Voltage (V)

Voltages (V)

charge time (hours)

Voltages (V)

Discharge capacity (%)

Discharge characteristics

℃

BELTRONA GmbH & Co. KG

electronic components

Schmeienstraße 50

D-72510 Stetten a.k.M.

Telefon +49 75 73 951 33 0

Telefax +49 75 73 951 33 99

www.beltrona.de

info@beltrona.de

BELNIMHSC3000

1.2V 3000 mAh

1 / 7

Summary of content (7 pages)

PAGE 1
BELNIMHSC3000 1.2V 3000 mAh Typical characteristics Standard charge characteristics Charge: 0.1C ×16hrs. (Type)：LP43SC3000P 0.2C 300min 315min mm 22.5-0.7 43.0-1.0 gram 53 10m(Max) Minimum Typical Diameter Dimensions Height Weight(Approximately) Internal Impedance At 1000 Hz Standard Rapid Charge Ambient temperature Charge standard After Charge） 300mA(0.1C)×16hrs 600mA(0.2C)×6.0hrs ℃ 0℃ to 40℃ Storage ℃ charge time (hours) Rapid charge Charge: 0.2C×6.0hrs.
PAGE 2
BELNIMHSC3000 1.2V 3000 mAh Standard according as IEC of test cycle life。 1. PREFACE The specification is suitable for the performance of NI-MH rechargeable battery produced by the SHENZHEN FBTECH CO., LTD. 2. MODEL SC3000mAh 1.2V 3. APPEARANCE There shall be no such details as discoloration or electrolyte leakage or 0 voltage. 4. RATINGS Description Nominal Voltage Typical Capacity Nominal Capacity Minimum Capacity Standard Charge Unit Specification V 1.
PAGE 3
BELNIMHSC3000 1.2V 3000 mAh 5. PERFORMANCE Before proceed the following tests, the cells should be discharged at 0.2C to 1.0V cutoff. Unless otherwise stated, tests should be done within one month of delivery under the following conditions: Ambient temperature: Relative Humidity: 20℃±5℃ 65±20% Note Standard Charge/Discharge Conditions: Charge: Discharge: Test Capacity High Rate Discharge (5.0C) Low Temperature Discharge Overcharge Charge Retention IEC Cycle Life Test Humidity 600mA(0.2C) to 1.
PAGE 4
BELNIMHSC3000 1.2V 3000 mAh External Short Circuit N/A Safety Device Operation N/A Free falling(drop) N/A No fire and explosion no No explosion △V<0.02V/cell △Ri<5%/cell After standard charge, short-circuit the cell at 20℃±5℃ until the cell temperature returns to ambient temperature.(cross section of the wire or connector should be more than 0.75mm2) Forced discharge at 0.2C to a final voltage of 0V,then the current be increased to 1C and forced discharge continue for 60 min Charge at 0.
PAGE 5
BELNIMHSC3000 1.2V 3000 mAh 6. PRECAUTIONS TO ENSURE THE SAFETY ON BANDING BATTERY 1. Batteries should be charged prior to use. 2. .When using a new battery for the first time or after long term storage, please fully charge the battery before use. 3. For charging methods please referrence to our technical handbook. 4. Use the correct charger for Ni-Cd or Ni-MH batteries. 5. Do not reverse charge batteries. 6. Do not short circuit batteries, permanent damage to batteries may result. 7.
PAGE 6
BELNIMHSC3000 1.2V 3000 mAh When connecting a battery pack to a charger, ensure correct polarity. 15. If find any noise, excessive temperature or leakage from a battery, please stop its use. 16. When the battery is hot, please do not touch it and handle it, until it has cooled down. 17. Do not remove the outer sleeve from a battery pack nor cut into its housing. 18. When find battery power down during use, please switch off the device to avoid overdischarge. 19.
PAGE 7
BELNIMHSC3000 1.2V 3000 mAh 7. Append: IEC61951-2 ED3.0 Endurance in cycles Before the endurance in cycles test, the cell shall be discharged at 0.2 1tA to a final voltage of 1.0V/sell. The following endurance test shall then be carried out, irrespective of cell designation, in an ambient temperature of 20℃±5℃.Charge and discharge shall be carried out at constant current throughout, using the conditions specified in table 5.