Wireless accessories F ti Functional l test t t ‐ Quick Q i k Guide G id GTO, January 2011
Beltone Direct Line Contents Beltone Direct Line: Tests – General information 3 Beltone Direct Line: Wireless connections 5 Beltone Direct Remote Control - Pairing test 6 Beltone Direct Remote Control – Functional test 7 Beltone Direct TV Link – Pairing test 10 Beltone Direct TV Link – Streaming test 11 Beltone Direct TV Link – Alternative pairing as 2nd or 3rd channel 12 Beltone Direct Phone Link – General information 13 B lt Beltone Di t Phone Direct Ph Li Link k – Pairing P i i with it
Direct Line service test Functionality test in Direct Line These instructions are meant for a quick functional test of the Beltone Direct Line devices. The tests performed by following these instructions will test all functions of a Direct Line accessory both electrically and electro-mechanical. The test is meant as a quick first hand evaluation in a service situation, whether a Direct Line device is working as intended. These instructions should not be read as a user guide.
Direct Line service test Test structure: Each device test consists of two parts, a pairing procedure and a function procedure. The pairing will ensure that the transmitter and receiver part of the device is working correctly. The functional test will ensure that the electromechanical parts, parts switches, switches plugs and cables are working correctly. correctly It is recommended to run both parts of the test for each device, even though they are separated in the table on contents.
Direct Line wireless connections Beltone TRUE™ AirlinkTM Beltone Direct Line Phone Link Beltone SolusPro® fittingg software Beltone Direct Line TV Link Beltone Direct Line Remote Control Mobile phone Cable connection 2.
Remote Control – p part 1 ((Pairing) g) Equipment used in this test: 1 TRUE device programmed for Right side 1 TRUE device programmed for Left side Optional – 1 Direct Line TV Link (SAS). The SAS is not necessary for checking the functionality of the Remote Control. If a SAS is used for this test it needs to be paired with the TRUE devices prior to this test. 1. Put the Remote Control in pairing mode. • • • • • DO NOT switch TRUE devices on yet yet.
Remote Control – p part 2 ((Functional Test)) 1. 2. 3. With the devices connected, check the buttons on Remote Control. • If the Remote Control is in stand by mode (Display not lid), pressing any button will bring it to active mode, but will not perform the function of the button. • For the following tests move Remote Control approximately 150 cm away from TRUE devices. Press Program button once. • TRUE devices will play Preset2 sound.
Remote Control – part 2 (Functional Test) 3a. Press Left button Fig 3a. . The Remote Control will now only adjust the Left side TRUE device. The Right side setting will still be displayed and the device is still connected. Check that the display has changed to Fig. 3a 3b. Press Plus button a couple p of times. Right side : No adjust. Left side: Adjusted Fig 3b. The Remote Control will turn up the volume in the Left side TRUE only. Check that the Left side TRUE turns volume up.
Remote Control – part 2 (Functional Test) 4. Press Home button Sound sample: Preset 1 . Pressing the Home button will: • Activate preset 1 in both hearing instruments and play preset 1 sound. • Adjust both hearing instruments to default volume settings • Set volume to simultaneous adjustment mode Check that the Display changes back to default setting 5.
TV Link – part 1 (Pairing) Equipment used in this test: 1 TRUE device programmed for Right side 1 TRUE device programmed for Left side Headphone output on PC. Optional - 1 Direct Line Remote Control. The Remote Control is not necessary for checking the functionality of the SAS. If a Remote Control is used for this test it needs to be paired with the TRUE devices prior to this test. 1. 2 2. Prepare p for pairing p g of TRUE devices with SAS. • DO NOT switch the TRUE devices on yet.
TV Link – part 1 (Streaming) 1. Prepare for TV connection PC . • Connect the red and white plug on SAS to the headphone output on the PC. Use the Jack adaptor. • Switch the TRUE devices to the streaming (SAS) program by pressing the push button on each TRUE devices for three seconds seconds. • As an alternative, press the SAS button on Remote Control • Each TRUE device will play the SAS connection sound Audio Left Audio Right Mono/Stereo Power Paring 2. Streaming music from PC.
TV Link – part 1 (Pairing) Alternative pairing for 2nd or 3rd Direct Line TV Link Link. It is possible to pair up to three Beltone Direct Line TV Links with a given pair of TRUE devices. For testing pairing function for a second TV Link follow instructions for channel 1 (default), but press the pairing button on SAS twice (three times for third Direct Line TV) TV). Pairing as second Direct Line TV will be indicated by Channel 2 light switches on. Channel 2 indicator End of test.
Phone Link – General information Direct Line Phone Link (BTB): • The BTB (BlueToothBridge) is a “bridge” between the Bluetooth “world” and the Direct LineTM wireless 2.4 GHz “world”. • • BTB must be paired in both these directions meaning: • Pairing with TRUE devices • Pairing with the Bluetooth device providing input to BTB. Two different procedures for pairing BTB with Bluetooth device are described in this document.
Phone Link – Pairing with TRUE Equipment used in this test: 1 Direct LineTM charger 1 or 2 TRUE devices. 1. Checking Charger and charging. • Before any tests is performed, make sure the BTB is charged • Connect the charger to the mini-USB socket on the BTB. • Check that the LED turns red (or green if BTB is fully charged). 2. Prepare for pairing of TRUE devices with BTB. • ! Applicable for both Bluetooth pairing procedures. DO NOT switch TRUE devices on yet.
Phone Link – Mobile phone paring 1. Prepare for pairing of BTB with mobile phone. • The Mobile phone will be the ”Searching” device and the BTB will be the ”Found” device” • The pairing procedure is controlled by the mobile phone. • Procedure may vary depending on the mobile phone used, but the steps and sequence will be very similar. • Refer to the manual for the mobile phone. p In the following example a Blackberry 8900 phone is used .
Phone Link – Mobile phone pairing 4. Pairing of BTB with mobile phone. • Follow the 5 steps below : 1. Select Search mode on the phone. 2. Wait until the search is finalized. The Phone will find all available Bluetooth devices within the range of the phone. 3. In the found devices select ”Hearing Aid Phone” which is the Bluetooth device name for BTB. 4. Enter passkey 0000 (four zero’s) 5. Pairing complete, connect to BTB – ready for use.
Phone Link – Bluetooth PC pairing Equipment used in this test: PC ( running this presentation) with Bluetooth functionality, Windows XP and Service Pack 3. English version. Other country local settings might influence the Bluetooth Setup. (- alternatively install a Jabra A320s Bluetooth USB adaptor) Start Windows Bluetooth Setup Wizard. • Make sure the BTB is turned OFF. • In the PC • Click on • In the Bluetooth Tasks menu select : ”Add a Bluetooth Device”.
Phone Link – Bluetooth PC pairing • The Wizard will list the services available for the selected device. • For this test you only need the ”Stereo Audio” service. • Use the service in default settings – do not use [ Configure ] b tt button. • Click [ Next >] Functional Test – Quick Guide | Global Technical Operation | Page 18 • The Wizard will search for all Bluetooth devices within range. • All found devices will be listed in the Selection window.
Phone Link – Bluetooth PC pairing Functional Test – Quick Guide | Global Technical Operation | Page 19 • The Wizard has placed a shortcut to Hearing Aid Phone (BTB) in My Bluetooth Places on PC. • This shortcut can be used for future parings with other BTB’s to be tested. • Click [ OK ] • The Wizard is now ready to make the final connection to the BTB BTB. • Click [ Finish ] • The Wizard will show the receipt window (shown below this text), and the pairing and connection is complete.
Phone Link – BTB functional Test 1. BTB paired with Bluetooth PC. • Make sure BTB is connected to Bluetooth PC. • Switch the TRUE devices on. • The Th TRUE devices d i will ill play l the th Delayed D l d Activation A ti ti sound d • Play one of the music files from the Sound files library. • Check that the TRUE devices switches to BTB mode and starts playing the music. • When the music stops, the TRUE devices will switch back to normal HI mode. Sound files library Classic Pop Rock 2.
Beltone Airlink 1. Testing Beltone Airlink The Beltone Direct Line Airlink is a device primarily used by hearing care professionals during fitting of the TRUE wireless products. No special functional test is available for Airlink. For testing a Direct Line Airlink, a TRUE device should be paired using the SolusPro fitting software.
