PRODUCT SPECIFICATION PRODUCT DESCRIPTION: UNIVERSAL SERIAL BUS TYPE-C RECEPTACLE SERIES PRODUCT NUMBER: 80397 Series(PROPOSAL) REVISION: ECR/ECN NUMBER: 1 EK2017-0*** DATE: DOCUMENT NUMBER PS-80397-001 CREATED / REVISED BY: 2017 / 05/ 22 SHEET No. Eric Bai TEMPLATE FILENAME: PRODUCT_SPEC REV 0.
PRODUCT SPECIFICATION 1.0 SCOPE………………………………………………………………………3 2.0 Applicable Document……………………………………………….3 3.0 Requirements……………….3 4.0 RATINGS……………………………………………………………………3 5.0 PERFORMANCE AND TEST DESCRIPTION………………………..3 5.1 APPEARANCE REQUIREMENTS…………………………………….3 5.2 ELECTRICAL REQUIREMENTS …………………………………3.4 5.3 MECHANICAL REQUIREMENTS…………………………………4~6 5.4 ENVIRONMENTAL REQUIREMENTS…………………………….6~7 6.0 TESTING SEQUENCE…………….
PRODUCT SPECIFICATION 1.0 SCOPE This product specification defines the product performance and the test methods to ensure the performance of the USB TYPE C , which is designed and manufactured by Bellwether Electronic corp. Applicable material No：80397 series Tests and inspection shall be performed in accordance with the requirements, tests and methods contained herein. A re-qualification test shall be conducted immediately following all major process changes. 2.
PRODUCT SPECIFICATION Mate connectors: apply a maximum voltage of 20 mV and a current of 100 mA. Measurement is made from the solder tail of the receptacle to the soldering point of the plug (including any internal paddle cards, contacts and substrates of the plug and receptacle). Per EIA-364-23B 40 milliohms ,[initial] MAX. PER CONTACT 10 milliohms MAX.
PRODUCT SPECIFICATION 10 Vibration Waveform:Sine wave Frequency:10-55-10 Hz in 1 minute Amp:1.52mm Direction: X.Y.Z.(3 directions) Duration:2 hours per each direction Discontinuities:<0.1µs. (EIA-364-28 Condition VII, Test letter D) Appearance: no damage. Discontinuity: 1 microsecond Max The connector family shall be tested for continuity under stress using the test configurations shown in following figure. 11 Discontinuity1 μs MAX.
PRODUCT SPECIFICATION 14 Drop 76cm Height one carton 6-sydes random dropping. Appearance: No abnormality Function : OK 5.4 ENVIRONMENTAL REQUIREMENTS ITEM TEST DESCRIPTION TEST CONDITION REQUIREMENT est Condition I 10 CYCLES –55℃ AND +85℃ 15 No physical damage & 10 milliohms MAX. (change from initial) Thermal Shock 25 °C /80 %RH for 1hr. Upper-Ramp for 0.5hr 65 °C /50 %RH for 1 hr. Down-Ramp for0.5hr, Total 24 Cycles, 72hrs 16 No physical damage & 10 milliohms MAX.
PRODUCT SPECIFICATION 18 19 Mixed Flowing Gas Salt Spray Subject mated connectors into the chamber, the connector shall be mounted on appropriate LLCR boards No physical damage. and exposed to: Contact Resistanc： a) Relative Humidity: 70%+/-2% b) 50 mΩ Max. Temperature: 30℃+/-1℃ c) Duration: 7 days. d) Invironmental Class: IIA (EIA-36465.) The mated connectors shall be exposed to the following salt mist conditions.
PRODUCT SPECIFICATION 1：Shall meet visual requirements, show no physical damage, and meet requirement of additional tests as specified in the test sequence in Figures 2 2：Resistance to soldering process is indicated on notes of customer drawing. Select the appropriate test type which drawing notes are matched with. REVISION: ECR/ECN NUMBER: 1 EK2017-0*** DATE: DOCUMENT NUMBER PS-80397-001 CREATED / REVISED BY: 2017 / 05/ 22 SHEET No. Eric Bai TEMPLATE FILENAME: PRODUCT_SPEC REV 0.
PRODUCT SPECIFICATION 6.
PRODUCT SPECIFICATION FIGURE 2. CONTACT RESISTANCE Example of 4-Axes Continuity Test FIGURE 4-1 Wrenching Strength REVISION: ECR/ECN NUMBER: 1 EK2017-0*** DATE: DOCUMENT NUMBER PS-80397-001 CREATED / REVISED BY: 2017 / 05/ 22 SHEET No. Eric Bai TEMPLATE FILENAME: PRODUCT_SPEC REV 0.
PRODUCT SPECIFICATION FIGURE 4-2 Wrenching Strength REVISION: ECR/ECN NUMBER: 1 EK2017-0*** DATE: DOCUMENT NUMBER PS-80397-001 CREATED / REVISED BY: 2017 / 05/ 22 SHEET No. Eric Bai TEMPLATE FILENAME: PRODUCT_SPEC REV 0.
