工程部 2017.02.09 正式发行 工程部 2017.02.
工程部 2017.02.09 正式发行 工程部 2017.02.
PRODUCT SPECIFICATION PRODUCT DESCRIPTION: UNIVERSAL SERIAL BUS TYPE-C RECEPTACLE AND PLUG SERIES PRODUCT NUMBER: 80210 Series / 80211 Series REVISION: ECR/ECN NUMBER: 1 EK2016-0203 DATE: 2016 / 07/ 03 DOCUMENT NUMBER SHEET No. PS-80210-001 1 of 8 CREATED / REVISED BY: CHECKED BY: APPROVED BY: Kaysen Chen Jerry Wang Jerry Wang TEMPLATE FILENAME: PRODUCT_SPEC REV 0.
PRODUCT SPECIFICATION 1.0 SCOPE………………………………………………………………………3 2.0 PRODUCT DESCRIPTION……………………………………………….3 3.0 APPLICABLE DOCUMENTS AND SPECIFICATION……………….3 4.0 RATINGS……………………………………………………………………3 5.0 PERFORMANCE…………………………………………………………..3 5.1 APPEARANCE REQUIREMENTS…………………………………….3 5.2 ELECTRICAL REQUIREMENTS ……………………………………...4 5.3 MECHANICAL REQUIREMENTS……………………………………...4 5.4 ENVIRONMENTAL REQUIREMENTS……………………………..….6 6.0 TESTING SEQUENCE…………….………………………………………7 7.
PRODUCT SPECIFICATION 1.0 SCOPE The Product Specification covers performance, tests and quality requirements for the USB Type-C Receptacles, Plugs. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) PRODUCT NAME: 0.50MM PITCH, USB TYPE-C RECEPTACLE AND PLUG CONNECTOR. SERIES NUMBER(S): 80210 / 80211 series 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS See the appropriate Sales Drawings for information on dimensions, materials, plating, and markings. 3.
PRODUCT SPECIFICATION 5.2 ELECTRICAL REQUIREMENTS ITEM TEST DESCRIPTION TEST CONDITION REQUIREMENT 2 Contact Resistance (Low Level) Mate connectors: apply a maximum voltage of 20 mV and a current of 100 mA. Measurement is made from the solder tail of the receptacle to the soldering point of the plug (including any internal paddle cards, contacts and substrates of the plug and receptacle).
PRODUCT SPECIFICATION 9 Cable Pull-out Apply a 40N axial load to cable assembly for a minimum of 1 minute while clamping one end of the cable plug. Per EIA 364-38, Method A No physical damage The connector family shall be tested for continuity under stress using the test configurations shown in following figure. 10 Discontinuity1 μs MAX.
PRODUCT SPECIFICATION 13 Shock (Mechanical) Discontinuity1 μs MAX. & No physical damage & 10 milliohms MAX. (change from initial) Mate connectors and shock at 50 g’s with ½sine wave (11 milliseconds) , 3 strokes in the ±X, ±Y, ± Z axes Per EIA-364-27, Condition A 5.4 ENVIRONMENTAL REQUIREMENTS ITEM TEST DESCRIPTION 14 15 Thermal Shock TEST CONDITION REQUIREMENT Mate connectors to follow condition for 10 cycles. 1 cycles a). –55 +0/-3 ℃, 30 minutes b)+25+10/-5 ℃, 5 minutes MAX. c).
PRODUCT SPECIFICATION 6.0 TESTING SEQUENCE 6.
PRODUCT SPECIFICATION 7.0 IR PROFILE Recommended Reflow Pre-Solder Process and Profile. Actual reflow profile also depends on equipment, solder paste, PCB thickness, and other components on the board. Please consult your solder paste & reflow equipment manufacturer for their recommendations to adopt a suitable process. 260℃ Max for 10 seconds, 2 cycles(Peak Temperature) Notes: 1. Reflow solder Preheat at 3°C/s to 150°C. 2. Reflow at 255°C for 30s per figure. 3. Peak temperature to be at 260 +0/-5°C.
