Installation Testen 1 Ziehen Sie am Batterie Streifen um den Sender zu aktivieren. Reinigen Sie die Wand mit dem Feuchttuch und entfernen Sie die Schutzfolie von dem Klettverschluss. 2 Montieren Sie den Sender an der Wand. Ggf. die mitgelieferte Schraube nutzen. 3 Schließen Sie das Kabel an einer der ”N” Anschlüsse an. 1 Bitten Sie einen Freund, Sie an Ihrem Festnetz-Telefon anzurufen.
Zubehör Technische Information Der Telefon-Sender kann mit folgendem Zubehör ergänzt werden: Stromversorgung Leistungsaufnahme Betriebsdauer Aktivierung 1 2 3 4 Kontakt Matte – wird aktiviert, wenn jemand auf sie tritt Mobile Phone Sensor – wird aktiviert, wenn Ihr Handy klingelt Magnetschalter – wird aktiviert, wenn eine Tür/Fenster geöffnet/geschlossen wird Externes Trigger-Kabel – Zum Anschluss an eine Türklingel/Gegensprechanlage 3 4 Zusätzliche Informationen 1 2 Lesen Sie mehr in der Installe
Fehlerbehebung 7 DE Wenn Versuchen sie Wenn Versuchen sie Zwei orangefarbene Lichter leuchten einmal pro Minute auf • Wechseln Sie die Batterien. Verwenden Sie nur 1,5 V AA (LR6) Lithium oder Alkalie-Batterien. Kein grünes Licht auf dem Sender, beim drücken der Test-Taste erscheint Ein grünes Licht am Telefonsender erscheint aber der Empfänger wird nicht aktiviert • Überprüfen Sie die Batterien und Stecker des Telefonsenders und des Empfängers.
Installer’s Guide 59 Introduction 61 Installation 62 Testing 63 Advanced testing 65 Customizing the signal 75 Trouble shooting 77 Trigger input 78 Technical information 58
Introduction Overview Function The telehone transmitter is part of the Visit alerting system that helps people with hearing loss to notice signals in their home. It detects landline phones by default but can also detect a number of other sources. Test buttons Connections Landline telephone RJ11 input to analogue telephone network: 26 - 120 V RMS, 15 - 100 Hz. Smartphone or tablet 2.
Installation Testing 1 Remove the battery pull tag to start the telephone transmitter. Clean the wall with the wet wipe and remove the protective film from the Velcro. 2 Mount the telephone transmitter on the wall. You can also use a screw and plug. 3 Connect the telephone adapter between the telephone plug and the socket. 1 Use your mobile phone to call the landline telephone.
Advanced testing Default indication and signal Testing the telephone transmitter is easy. First, make sure that the telephone transmitter is installed properly. For instructions, read the section Installation. Transmitter indication When the transmitter is activated, the LED lights up in green. This means that the batteries are in good condition. Change batteries if the LEDs blink in orange. Receiver signal When a receiver is activated, it signals with sound, flashes or vibrations.
Customizing the signal The telephone transmitter controls the signal pattern on the receiver. Use the signal switches to customize the signal pattern. How to customize the signal pattern Move the signal switches 1 on the Telephone transmitter according to the tables on the following spreads. Signal switches (See table) Down = Off Changing the radio key All Visit products are set to the same radio key from factory and all switches are positioned down=off per default.
Signal output for 868 MHz and 315 MHz Dip switch 67 Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Light Yellow light Blinking in yellow Vibration Fast pattern Fast pattern Green light Light 2 x yellow blinks Yellow light 3 x orange blinks Slow pattern Vibration Rapid pattern Fast pattern Sound 1 x ring, Lo Rapid pattern 2 x ring ring, Hi 1 x ding dong, Lo Sound 2 x r
Signal output for 868 MHz and 315 MHz Dip switch 69 Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Dip switch Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Light Blinking in yellow Yellow light Green light Light 3 x yellow blinks Yellow light 3 x orange blinks Vibration Fast pattern Fast pattern Slow pattern Vibration Fast pattern Fast pattern Rapid pattern Sound 2 x ring ring, Hi 1 x ring, Lo 1 x ding dong, Lo S
Signal output for 433 MHz Dip switch 71 Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Dip switch Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Light Yellow light Yellow light Green light Light Yellow light Yellow light Orange light Vibration Slow pattern Fast pattern Slow pattern Vibration Slow pattern Fast pattern Fast pattern Sound 1 x ding dong, Hi 1 x ring, Lo 1 x ding dong, Lo Sound 1 x ding dong, Hi 1 x
Signal output for 433 MHz Dip switch 73 Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Output Test button 1 and 2 Landline phone Mobile phone sensor External trigger Light Yellow light Yellow light Vibration Fast pattern Slow pattern Green light Light Yellow light Yellow light Orange light Slow pattern Vibration Fast pattern Slow pattern Sound 1 x ring, Lo Slow pattern 1 x ding dong, Hi 1 x ding dong, Lo Sound 1 x ring, Lo 1 x ding dong, Hi Li
Trouble shooting If Try this If Try this Two orange lights appear every minute • Change batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries. A green light appears on the transmitter but the receiver is not activated • Check the telephone transmitter’s and the receiver’s batteries and connections. No green light appears on the transmitter when I press the test button(s) • Change batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries.
Trigger input Technical information You can use both stereo and mono plugs. The 3.5 mm input is located on the top right side and the 2.5 mm input under the lid. Power supply Power consumption Operating time Activation Mono Trig is made by closing the two connectors Stereo Trig is made by: 1 Closing the outer and middle connector or closing the outer and inner connector 2 Applying 2-30VDC or 3-24VAC 5-150Hz between the middle and inner connector Please note When you use the 2.
Hereby, Bellman & Symfon declares that this Telephone transmitter is in compliance with the essential requirements and other relevant provisions of directives: R&TTE 1999/5/EC, LVD 1973/23/EC, EMC 1989/336/EC, MDD 1993/42/EEC. FCC compliance statement This device complies with Part 15 of the FCC Rules.
bellman.
