Users Guide & Installation Handbook Belling IH60 UK Part No 082749202 Date 21/11/2012
contents & INTRODUCTION CONTENTS Warranty • SAFETY • USING THE product • cleaning • INSTALLATION INSTRUCTIONS • technical data • CUSTOMER CARE Your new appliance comes with our 12-month guarantee, protecting you against electrical and mechanical breakdown. To register your appliance please call 0844 481 0182, complete the registration form included or register online at the web address located on the back page of this book.
Safety WARNING! This appliance and its accessible parts may become hot during use. To avoid burns, children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Safety General Fire Safety Advice Servicing should be carried out only by authorised personnel. Most kitchen fires occur when people are distracted or leave things unattended, so remember: Do not spray aerosols in the vicinity of this appliance while it is in operation. Do not store or use flammable liquids or items in the vicinity of this appliance. Do not modify this appliance. • • • • Always ensure that pan bases are dry, stable and flat before using them on the hob.
Safety Avoiding damage to the appliance. The ceramic glass of the hob can be damaged by objects falling onto it. Be especially careful with heavy jars of food being stored in cupboards above the hob, we recommend storing them away from the hob area. The edge of the glass can be damaged by being knocked by cookware. Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the ceramic glass if pushed across the surface.
USING THE HOB - INDUCTION Before using your hob It is recommended that you clean and wash the hob surface before using for the first time. Apply a thin coat of ceramic hob cleaner to the hob to maintain and protect it. See the customer care section for details of how to obtain all the available cleaning products. A warning will be activated and will beep every 10 seconds, to attract your attention, please remove any objects and clean the control area as appropriate.
USING THE HOB Central On/Off switch Power Boost The central on/off switch enables all of the cooking zones to be switched off simultaneously at a touch of a key. To switch on the hob The hob is switched On by touching the“ON/OFF” key for 1 sec. A beep sounds and all the heater displays show a full stop in the cook zone display. If the selection of a heater is not done in 10 seconds, the hob will turn off automatically. The hob is switched Off by touching the“ON/OFF” key for 1 sec.
USING THE HOB Pan Detection As soon as you lift the pan off the zone the power is automatically reduced, helping to save energy. • electrical implant should clarify with their doctor or the producer of the implant, whether there implant is adequate and fail-safe, The pacemaker must be designed in compliance with the appropriate regulations.
USING THE HOB Induction Cook Zone Smallest Recommended Diameter (mm) LHF 150 LHR 120 RHR 150 RHF 120 Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the ceramic glass surface which are difficult or impossible to remove. Pans unsuitable for Induction: Pans made of copper, stainless steel, aluminium, oven proof glass, wood, ceramic and terra-cotta.
USING THE HOB Troubleshooting The hob produces a smell the first few times it is used Heat a pan full of water on each zone for half an hour. Pans make a noise during cooking This is caused by vibration due to the passage of energy from the hob to the pan. On a high setting this is quite normal for certain types of saucepan. It will not damage the hob. The hob makes a slight clicking sound This is caused by the distribution of power between two heating zones on the same side of the hob. The hob won’t work.
USING THE HOB Appliance Errors Fault Description Action F0 Software Error Switch the power off and on, system should reset FA Safety key Error Switch the power off and on, system should reset FC Safety key Error Switch the power off and on, system should reset FE Touch Ntc Error Switch the power off and on, system should reset Ft Touch Ntc Error Switch the power off and on, system should reset Fc Touch Ntc Error T<90oC Advice do not put hot pans on control area, system should automatical
CLEANING Electric Hob follow the circular grooves and avoid damaging the red spots. Make sure that you allow the hotplate to dry before use by switching on the elements at a low heat. Ceramic glass hobs • • • It is recommended that you clean and wash the hob surface before using for the first time. Apply a thin coat of ceramic hob cleaner to the hob to help maintain and protect it. The ceramic hob top can be cleaned using a clean, damp cloth or kitchen paper.
installation General information Installation should only be carried out by a qualified installer or engineer. Please keep to the following points most carefully; Although every care has been taken to ensure this appliance has no burrs, or sharp edges, we recommend that you wear protective gloves when installing and moving this appliance. This will prevent injury. The minimum distances to other appliances and units are to be observed.
installation CHOOSING YOUR INSTALLATION Make sure that the air inlets through the ventilator grids underneath the hob are never blocked. We recommend that you install this appliance in a work top which is a minimum 38mm deep. The hob can be fitted into a work top less than 38mm deep, but the 20mm gap between hob base and appliance must be maintained. Installation above an oven Installation above a unit with a drawer or door An air outlet of 5mm underneath work surface is required.
installation Clearances and dimension – requirements No shelf or overhang of combustible material should be closer than 650mm above the hob. There must be a minimum clearance of 50mm between the edges of the hob and any side walls; this clearance must be maintained up to 420mm above the worktop. * 650mm min There must be a minimum clearance of 50mm between the rear edge of the hob and the rear wall. This clearance must be maintained up to 650mm above the worktop.
installation Fitting into worktop Recessed Method Cut a hole in the work surface to the required size. Recess the work top to the appropriate depth (Approx 5mm) and shape to fit the hob (add 1mm to overall glass size). Insert the hob into the recess, ensuring that the foam seal is sitting correctly. Locate and attach the securing clamps as required, Tighten the screws so that the hob is pulled down firmly against the worktop, thus ensuring a good seal.
installation Fixing Bracket Advice Dealing with sides, cross-rails and back-panels in the cabinetry. Depending on the cabinets, the worktop thickness and the hob positioning, it is possible for the hob base and/or the clamp brackets to interfere with parts of the cabinet. Cut away cabinetry and use appropriate fixing brackets for your installation. Note; It is neccesary to remove 4 x self tapping screws from the appliance in the desired fixing bracket locations.
installation Connect to the electricity supply Terminal Block Connection (For Fixed Wiring only) 6 WARNING: This appliance must be earthed. Only connect to the electrical mains terminal with the power switched off. The electrical mains terminal is live. Follow the terminal block connection schematic. 7 5 1 2 N 4 3 Loose and inappropriate connections can make the terminal overheat. Ensure the cable clamp is fitted correctly and securely.
TECHNICAL DATA SINGLE PHASE SUPPLY: 230 -240V ~ 50Hz 6.6kW - 7.2kW 3 PHASE SUPPLY: 230 / 400V 3N ~ 50Hz Individual Cook Zone Power Ratings Cook Zone Normal Power/Boost Power Rating kW LHF 1.5/2.0 LHR 1.2/1.6 RHR 1.5/2.0 RHF 1.2/1.
CUSTOMER CARE Customer Care Web Shop Having purchased a superior cooker, hob or hood from us, you’ll naturally want to keep it looking great. And who better to help you care for it than the manufacturer? We offer an extensive range of accessories, components and cleaning products which, will instantly give your cooker a good as new look. range of Bake ware and Cookware essentials including Roasting Pans, Cake Tins and Non-Stick Cooking Liners. For all enquires, please visit our Web Shop at www.gdhaonline.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
Please keep this handbook for future reference, or for anyone else who may use the appliance.
CUSTOMER CARE To contact Belling about your appliance, please call Warranty Registration 0844 481 0182 to register your appliance Customer Care Helpline 0844 815 3746 in case of difficulty within the UK Alternatively general, spares and service information is available from our website at www.belling.co.uk Please ensure that you have the product’s model no and serial no available when you call.
