Specifications

18 19
CARE AND CLEANING
• Beforetherstuseandaftereveryuse,cleaneachpartthoroughly.
• SwitchoffatthewallandunplugtheCakePopMakerandallowtocoolcompletelybefore
cleaning. There are no parts to disassemble for cleaning.
• The cooking plates shouldbe conditioned with oil before each use by lightly coating each
mould with vegetable oil, using a heat resistant silicone or plastic soft pastry brush.
• Periodicallycheckallpartsbeforereassembly.
• Neverimmersetheapplianceinwaterorotherliquids
• NeverplacetheCakePopMakerinthedishwasher
• Alwaysuseplastic,nylonorsiliconespatulasetc.–metaltoolswilldamagenon-stickcoatings.
• Neverimmersetheunitinwateroranyotherliquid.
• Tocleantheunitandcontrolpanel,wipewithaclean,dampclothanddrybeforestoring.
• Donotuseabrasivecleaners,steelwoolorabrasivematerialsorcleansers.
• AlwayscleantheoutsideofthecakePopMakerandthetopandbottomcookingplatesafter
each use to prevent a build-up of baked-on foods.
• Store the CakePopMaker with the power cableloosely coiled around base. Neverwrap it
tightly around the appliance.
• EnsurethattheCakePopMakeriscooled,cleananddrybeforestoringdonotplaceanything
on top of the Cake Pop Maker when storing.
RECYCLING YOUR ELECTRICALS
Along with many other high street retailers, Lakeland has joined a scheme whereby customers can
take their unwanted electricals to recycling points set up around the country.
Visit www.recycle-more.co.uk to find your nearest recycling point.
ELECTRICAL CONNECTIONS
THIS APPLIANCE MUST BE EARTHED
This appliance is fitted with a fused three-pin plug to BS1363 which is suitable for use in all homes
fitted with sockets to current specifications. If the fitted plug is not suitable for your socket outlets,
it should be cut off and carefully disposed of. To avoid an electric shock, do not insert the discarded
plug into a socket.
Fitting a new plug
If for any reason you need to fit a new plug, the flexible mains lead must be connected as shown
here. The wires in the mains lead fitted to this appliance are coloured in accordance with the
following code:
E
Earth(green/yellow)
L
N
Neutral(blue)
13amp FUSE
13amp fuse
Live(brown)
ConnectBLUEtoNeutral(N)
ConnectGREEN&YELLOWtoEarth(E)
ConnectBROWNtoLive(L)
13 amp fuse to be used
If the colours of the wires in the mains lead of this appliance do not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows. The wire which is coloured
greenandyellowMUSTbeconnectedtotheterminalwhichismarkedwiththeletterE(Earth)
or coloured green. The wire which is coloured blue MUST be connected to the terminal which is
markedwiththeletterN(Neutral)orcolouredblack.ThewirewhichiscolouredbrownMUSTbe
connectedtotheterminalwhichismarkedwiththeletterL(Live)orcolouredred.
Before refitting the plug cover, check that there are no cut or stray strands of wire inside the plug.
Use a 13 amp BS1362 fuse. Only BSI or ASTA approved fuses should be used. If you are at all unsure
which plug or fuse to use, always refer to a qualified electrician.
Note: after replacing or changing a fuse on a moulded plug which has a fuse cover, the cover must
berettedtotheplug;theappliancemustnotbeusedwithoutafusecover.Iflost,replacement
fuse covers can be obtained from an electrical shop. This appliance complies with the following
EECDirectives:2006/95/EC(LowVoltageDirective)and89/336EEC(EMCDirective)