Specifications
Table Of Contents
- TABLE OF CONTENTS
- Introduction
- Basic System Operation
- Panel Controls
- Number and Letter Buttons
- Call sequence
- Silent viewing
- Apartment Station Controls
- Auto Display
- Ringer Mute
- Door Status Indication
- Call Privacy
- User Activation (CCTV Mode)
- Cameras
- Extension Apartment Stations
- Lock Type
- Exit Button and Fire Switch
- Trades Facility
- DDA Functionality
- Multiple Entrances
- Gate and Block Systems
- Design Considerations
- Installation & Commissioning
- Checklist
- Wiring
- Commissioning
- BFD-DIG Door Controller Settings
- Security
- Panel Programming
- ACOD – Primary Access Code
- TCOD – Secondary Access Code or Tradesmen’s Code
- LTIM – Lock Release Operating Time
- LOCK – Lock Type
- CAM2 – Second Camera Present?
- TRAD – Door Button Trades Mode
- DMON – Door Status Switch
- RECP – Reception Phone Address
- PSEC – Panel Security Key
- PPRG – Phone Programming Security Key
- RING – Ringing Time/Call Time and Ring Effect
- TALK – Talking Time/Apartment Station Active
- TONE – Re-assurance Tone
- CANC – Cancel Key Compatibility
- BCAL – Bellcall Compatibility Mode
- 12A? – Flat 13 Numbered as 12A (From build 4)
- BFD-DIG Door Controller Jumper Settings
- BSC4 Video Controller Settings
- BF Apartment Station Switch Settings
- BS Videophone Switch Settings
- ATTENTION
- Troubleshooting
- Specifications
- Diagram A – Basic System Wiring Overview
- Diagram B – BFD_DIG PCB Detail
- Diagram C – BFD-DIG Keypad Matrix
- Diagram D – Basic System Wiring Detail
- Diagram E – BSC4 PCB Detail
- Diagram F – BSC4 Wiring Detail
- Diagram G – Large system Overview
- Diagram H – Extension Apartment Station Wiring
- Diagram I – Apartment Station Local Power Wiring
- Diagram J – Camera Sharing & Time Clock Sharing
- Diagram K – Combined Connections bellfree With Lock
- Diagram L – Combined Connections Third Party Lock
- Safety Information and Declarations
BF Apartment Station Digital Entry System
PD–166 Issue 1 Installation and Operating Manual Page 42 of 48
Diagram K – Combined Connections bell
free
With Lock
Connecting a Bell PAX1 Proximity Reader
Connect the lock release as per this manual. Leave the Proximity Reader set to
fail secure, the BFD controller sets the lock type.
Use a lock time card to reduce the lock time to 1 or 2 seconds, otherwise the
PAX1 will extend the bellfree lock time to 7 seconds. Lock time cards are in all
Fob packs except the starter pack.
Note 1. A normally open exit button can still be wired to the BFD controller in addition to
the proximity wiring. Alternatively the exit button can be wired to the proximity
reader
ACT 1000/2000/3000 Proximity Controller or 100e/200e Extender
The lock output on an ACT controller is a volt free relay contact, so as long as it is
not used for another purpose it can be directly connected to the exit input of a
bellfree door controller.
A 2 wire interface is shown, but if a common 12V supply is in use then the Exit-
input may be left unconnected and the corresponding ACT relay connection can be
connected to a local 0V terminal.
bellfree
Door
Controller
bellfree
Door
Controller
bellfree
Door
Controller
Exit
Exit
PAX1
Proximity
Reader
PAX1
Proximity
Reader
+
+
–
–
12V
12V
+
+
–
–
Lock
Lock
Exit
Exit
OV
OV
+12V
+12V
–
–
+
+
Z
Z
O
O
H
H
C
C
Exit button
(Optional)
Exit button
(Optional)
NO
C
NC
Exit
+
–
ACT
OP1 or
Relay 1