Specifications
Table Of Contents
- TABLE OF CONTENTS
- Introduction
- Basic System Operation
- Panel Controls
- Number and Letter Buttons
- Call sequence
- Silent viewing
- Apartment Station Controls
- Auto Display
- Ringer Mute
- Door Status Indication
- Call Privacy
- User Activation (CCTV Mode)
- Cameras
- Extension Apartment Stations
- Lock Type
- Exit Button and Fire Switch
- Trades Facility
- DDA Functionality
- Multiple Entrances
- Gate and Block Systems
- Design Considerations
- Installation & Commissioning
- Checklist
- Wiring
- Commissioning
- BFD-DIG Door Controller Settings
- Security
- Panel Programming
- ACOD – Primary Access Code
- TCOD – Secondary Access Code or Tradesmen’s Code
- LTIM – Lock Release Operating Time
- LOCK – Lock Type
- CAM2 – Second Camera Present?
- TRAD – Door Button Trades Mode
- DMON – Door Status Switch
- RECP – Reception Phone Address
- PSEC – Panel Security Key
- PPRG – Phone Programming Security Key
- RING – Ringing Time/Call Time and Ring Effect
- TALK – Talking Time/Apartment Station Active
- TONE – Re-assurance Tone
- CANC – Cancel Key Compatibility
- BCAL – Bellcall Compatibility Mode
- 12A? – Flat 13 Numbered as 12A (From build 4)
- BFD-DIG Door Controller Jumper Settings
- BSC4 Video Controller Settings
- BF Apartment Station Switch Settings
- BS Videophone Switch Settings
- ATTENTION
- Troubleshooting
- Specifications
- Diagram A – Basic System Wiring Overview
- Diagram B – BFD_DIG PCB Detail
- Diagram C – BFD-DIG Keypad Matrix
- Diagram D – Basic System Wiring Detail
- Diagram E – BSC4 PCB Detail
- Diagram F – BSC4 Wiring Detail
- Diagram G – Large system Overview
- Diagram H – Extension Apartment Station Wiring
- Diagram I – Apartment Station Local Power Wiring
- Diagram J – Camera Sharing & Time Clock Sharing
- Diagram K – Combined Connections bellfree With Lock
- Diagram L – Combined Connections Third Party Lock
- Safety Information and Declarations
BF Apartment Station Digital Entry System
PD–166 Issue 1 Installation and Operating Manual Page 19 of 48
BFD-DIG Door Controller Settings
The BFD-DIG is programmed from the panel for all settings.
Security
It is strongly recommended that the Panel Security Code (PSEC) be changed from its
factory setting to prevent unauthorised access. Record the new number carefully as it
cannot be easily changed if lost. It is also recommended that the Phone Programming
Code (PPRG), Coded Access Code (ACOD) and Trades Access Code (TCOD) are all
changed from default even if not used.
To access panel programming without the code requires physical access to the controller
PCB, borrow a jumper from say video gain (remember the setting) and place it on the 5 pin
programming header between pins 1 & 2. Now pressing the test button will enter panel
programming for 30S when the panel security code can be read or set. When the
programming is finished replace the jumper back to its original location.
Panel Programming
To use Panel Programming Mode: -
First type the Panel Security Code (initially [3434]) followed by the call button.
The display will show the first programmable parameter (ACOD), and then alternating
at 1 second intervals will be the value and the parameter name.
Press the door button to step down through the programmable parameters.
Press the reception button to step up through the programmable parameters.
The list rolls over bottom to top and vice versa.
To change a numeric parameter simply type a new 1-4 digit value and then press call.
To change other values simply press call to choose the next value.
To exit Panel Program Mode press cancel.
If no button is pressed for 30 seconds then programming mode will auto-cancel.
Code
Default
Access
Description
ACOD
1234
Coded access code – must be 4 digits
TCOD
6789
Trade access code – must be 4 digits
LTIM
0003
Lock Time: 1-99 seconds
LOCK
Secr
Lock Type: Secr (fail secure), Safe (fail safe)
CAM2
No
Camera 2: No (absent), Yes (present)
TRAD
0005
Trade Function: 0-9 – see table
DMON
Cwo
Door Monitor Polarity: Cwo, Owo
RECP
9898
Reception / Porter phone number
PSEC
3434
Panel security code
PPRG
1212
Phone programming security code
RING
0015
Ring Time – see table
TALK
0015
Talk Time – see table
TONE
Both
Ring and Lock Buzz-Tone enable, 4 settings
CANC
Yes
Allow Cancel button to terminate Call
BCAL
No
Bellcall BCP1 compatibility mode
12A?
No
Allows user entry of 12A to call BSC4 output 13