INSTRUCTIONS 7912B UNIVERSAL SOUNDBAR MOUNT Patent pending / Brevet en instance / Patent pendiente / Заявка на патент подана Made in China / Fabriqué en Chine / Hecho en China / Сделано в Китае Do not discard these instructions / Ne pas jeter ces instructions Conserve estas instrucciones / Не выбрасывайте эту инструкцию 121712v1T
PARTS LIST ENGLISH SB-MP Plastic Plate X2 A1 Horizontal Support Plate X1 SB-SP Metal Support Plate X2 A2 Vertical Metal Exterior Bars X2 A5 Square Adapters X2 A3 Vertical Plastic Interior Bars X2 SB-SC M10 Hollow Hex Bolt X2 A4 Extensions X2 N M5 Nut X6 JN M6 Nut X8 SB-SCN M10 Nut X2 II M5 x 26 mm X2 SB-A M4 x 22 mm X4 I M5 x 30 mm X2 SB-J M6 x 25 mm X4 SB-ML M8 x 32 mm X4 AF M8 Nut X6 J M6 x 12 mm X8 SB-M M8 x 30 mm X4 3 AB M4 x 10 mm X6 SB M8 Washer X8 AN M4 Nut X10 SB-R M6 Washer
BEFORE YOU BEGIN: It is necessary to ask yourself two important questions before you begin attaching your soundbar: • What type of mount is my soundbar? (See page 5) • Will I be displaying the soundbar ABOVE or BELOW my television? Keep the answers to these two important questions in mind as you proceed with these instructions.
PART 1: PREPARING TO MOUNT THE SOUNDBAR Determine how your soundbar is mounted There are three typical types speaker mounting methods for Soundbars: • KEYHOLE (Fig. 1): This is a slot with a larger circle at the bottom SEE PAGES 6-7 FOR THIS TYPE OF INSTALLATION Fig. 1 • SCREW (Fig. 2): This is commonly found on center channel speakers. There is a threaded nut in the back of the speaker to screw into. SEE PAGES 6-7 FOR THIS TYPE OF INSTALLATION Fig. 2 • BRACKET (Fig.
FOR KEYHOLE AND SCREW MOUNT SOUNDBARS: SKIP TO PAGE 8 IF YOUR SOUNDBAR IS THE MOUNTING BRACKET TYPE AND REQUIRES THE SQUARE MOUNTING ADAPTERS (A5). SB-SC Prepare the Support Brackets: SB-MP 1-1. Place the M10 Hollow Hex Bolt (SB-SC) into the large hexagonal opening in Plastic Support Bracket (SB-MP) as shown in Fig. 5. Fig. 5 If Mounting the Soundbar ABOVE the TV: 1-2. Place the Metal Support Plate (SB-SP) over the M10 Hollow Hex Bolt (SB-SC) and Plastic Support Bracket (SB-MP) as shown in Fig. 6.
Fig. 10 For Keyhole Mounting: SB-SP SB-MP 1-6. Insert the Long 26 mm Screw (II) through the center of the Large Hex Bolt (SB-SC) as shown in Fig. 10 (A longer 30 mm Screw (I) has been included if you require a longer length). Allow about 1/4" (6 mm) of space between the head of the screw and the Metal Support Plate (SB-SP) to fit the soundbar's keyhole. I or II SB-SC 1-7.
FOR BRACKET MOUNTED SOUNDBARS: Fig. 16 Fig. 15 AN SB-SC SB-MP SB-MP A5 ORIENTATION: Fig. 17 NOTE that the slots in the Square Adapters (A5) are different lengths. You will need to find the slot that BEST fits the mounting brackets that came with your soundbar. AA 1-1. Place the M10 Hollow Hex Bolt (SB-SC) into the large hexagonal opening in Plastic Support Bracket (SB-MP) as shown in Fig. 15. 1-2. Insert three small M4 Nuts (AN) into the cavities in Plastic Support Bracket (SB-MP) as shown in Fig.
PART 2: INSTALLING THE VERTICAL TELEVISION BARS 2-1. With the help of an assistant, and taking extreme caution not to damage the front of your television, lay the TV face-down on a flat, level, and very soft surface. You may want to use soft blankets or towels to cushion the face of the TV. Make sure the outer frame of the television is supported, and that no pressure is applied to the screen of the TV. Fig. 20 A3 2-2. Locate the mounting holes on the back of your TV.
FOR LARGE SIZE TELEVISIONS: Fig. 24 If your television is very large, you may need to extend the Vertical Metal Exterior Bars (A2) quite a distance from the mounting holes in your TV. 2-6. Extend the Vertical Metal Exterior Bars (A2) as far as you need to in order to accomodate your soundbar and TV, however MAKE SURE you leave at least two holes past the TV mounting screw as shown in Fig. 24. This will allow enough support to safely hold your soundbar in place.
PART 3: INSTALLING THE SOUNDBAR 3-1. Attach the Horizontal Support Plate (A1) to the protruding screws of the Vertical Metal Exterior Bars (A2) and secure using two M8 Washers (SB) and two M8 Nuts (AF). Make sure it is even and parallel with the frame of the TV, then tighten fully. (Figs. 27 & 28). Fig. 27 3-2. With the help of an assistant to hold the soundbar in place, attach the soundbar to the Universal Soundbar Mount as you did in Part 1.
