Hydronic Heating and Plumbing Products A-50R
Service and support from the most trusted name in the industry – Bell & Gossett®. The Bell & Gossett name has always stood for uncompromising quality and dependability. That’s evident in the way our products are built and backed by our outstanding customer service and support team. Your local Bell & Gossett representative is available any time and is an experienced professional with a wealth of technical expertise.
The Most Complete Line of Hydronic Heating and Plumbing Products. All from a Single Source – Bell & Gossett. Table of Contents Page Number Pumps ecocirc Series Heating/Cooling Circulators ........................................ 4-5 ecocirc XL Series Heating/Cooling Circulators .................................... 6-8 ecocirc e3 Series Potable Water Pumps .............................................. 9 ecocirc wireless Potable Water Kit .......................................................
CIRCULATORS ecocirc® auto Heating/Cooling Circulator Description ecocirc 19-14 auto are designed, with highly efficient electronically commutated permanent magnet motor (ECM/PM Technology), specifically for hydronic systems. Ideal for hydronic systems with zone or thermostatic valves, the ecocirc 19-14 auto can be used as replacements for existing circulators with induction motors as well as new construction as primary or zone circulators.
CIRCULATORS ecocirc® vario Heating/Cooling Circulator Description ecocirc 19-14 vario circulators are designed, with highly efficient electronically commutated permanent magnet motor (ECM/PM technology), specially for hydronic systems. The ecocirc 19-14 vario has a constant curve control, which allows the pump to follow the natural hydraulic curve of a circulator. Basically acts the same as a standard 3-speed pump except with a step-less dial resulting in infinite speed control.
CIRCULATORS ecocirc® XL High efficiency large wet rotor pump for heating, cooling and potable water systems Description The ecocirc XL is a high efficiency, variable speed, wet rotor pump with integrated drive. The circulator is available in cast iron or lead-free bronze and has a broad operating temperature range of 14°F to 230°F (-10°C to 110°C). The ecocirc XL is suitable for both hot and chilled water systems.
CIRCULATORS ecocirc® XL High efficiency large wet rotor pump for heating, cooling and potable water systems Self-flushing membrane Allows clean water to cool and lubricate the motor bearing. Restricts entry of abrasive particles. Economical operation A highly efficient ECM motor combined with optimized pump hydraulics, keeps operational costs at a minimum. User-friendly interface With only four logically placed buttons on an intuitive interface, it’s easy to set and operate the new ecocirc XL.
CIRCULATORS ecocirc® XL High efficiency large wet rotor pump for heating, cooling and potable water systems STANDARD OPERATING MODES Constant Speed Night Mode The pump maintains a constant speed at any flow rate. The desired speed is set on the interface panel of the pump. The pump will automatically reduce speed when there is an abrupt change in fluid temperature. The change in fluid temperature is from a boiler operating in night time setback mode. The built-in temperature sensor is used.
CIRCULATORS ecocirc® Series Potable Hot Water Recirculation Pumps - Whole House Description e3 circulators are energy efficient circulators using permanent magnet, ECM (electronically commutated motor) technology. The e3 circulators are designed specifically for potable water applications. These circulators are lead-free* and come with a variety of options including a temperature sensor, various body styles, assembled with electrical cord and plug.
CIRCULATORS ecocirc® wireless Potable Hot Water Recirculation Kit Description The ecocirc wireless is a potable hot water recirculation kit (a pump and valve combination) for instant supply of hot water supply throughout the entire house. The ecocirc pump is installed on the supply side of the hot water source and the mixing valve under the sink farthest away from the hot water source. The pump and valve are in constant wireless communication.
CIRCULATORS autocirc® Series Potable Hot Water Recirculation Pumps - Undersink Description autocirc® circulators are energy efficient using permanent magnet, ECM (electronically commutated motor) technology. The autocirc circulators are designed specifically for standard water heaters. These circulators are lead-free* and are assembled with a timer, cord and plug.
CIRCULATORS LS Condensate Removal Pump For Condensing Boilers and Air Conditioning /Cooling Systems Description The LS condensate removal pumps are energy efficient lifting stations that use permanent magnet, ECM (electronically commutated motor) technology. The LS condensate removal pumps are designed specifically for use in applications where the removal of condensate fluid is not possible by gravity.
CIRCULATORS ecocirc® SC Solar Pump Spherical Motor Pump Application • The ecocirc solar pump can be used for most circulation pump applications without connection to the power grid with direct connection to a photovoltaic panel. • This pump is perfect for single family home thermal solar systems or any circulation pump application where conventional power is not available, on closed loop systems 2.
CIRCULATORS Bell & Gossett Cast Iron Wet Rotor Circulators / NRF Description Materials of Construction A residential or light commercial, maintenance free, axial flanged, in-line, cast iron, wet rotor circulation pump for hydronic heating systems. UL and cUL Listed.
CIRCULATORS Bell & Gossett Cast Iron Wet Rotor Circulators / NRF Reliable, maintenance-free, whisper quiet wet rotor circulators designed for residential and light commercial heating systems.
CIRCULATORS Lead-Free Wet Rotor Circulators for Potable Water / NBF & SSF Description A residential or light commercial, maintenance-free, in-line, lead-free* bronze or stainless steel, wet rotor circulator for potable water systems and other applications. Flanged, union or sweat models available. UL and cUL listed.
CIRCULATORS Lead-Free Wet Rotor Circulators for Potable Water / NBF & SSF – continued Single Speed–NBF/SSF 60 HZ Performance Curve Three Speed–NBF 60 HZ Performance Curve CIRCULATORS Series LR™ Maintenance-Free Circulators Materials of Construction Pump Body: LR-20WR: Cast Iron LR-15BWR: Lead-Free* Bronze Impeller: Noryl® Shaft: Ceramic Bearings: Carbon *CSA certified to NSF/ANSI 372 that product contains less than 0.25% lead content by weight on wetted surface.
CIRCULATORS Maintenance-Free Circulators a superior alternative to large wet rotor pumps Operating Data Maximum Working Pressure: 150 PSI (10.
CIRCULATORS Oil Lubricated Circulators Three-Piece PD 40 PD 38 Operating Data PD 37 PR Maximum Working Pressure: 125 PSI (8.
CIRCULATORS Series 60 In-Line Mounted Centrifugal Pump Now Available with ECM Motor Description A maintenance-free, in-line, cast iron centrifugal pump for header pump applications.
CIRCULATORS Series 60 In-Line Mounted Centrifugal Pump Series 60 Standard Sizes 1750 RPM Series 60 Standard Sizes 1750 RPM Specifications Model Suction And Discharge Size Inches NPT Pump Dimension in Inches (mm) F G K L M N P R S T 601,602 & 603 1 6-7/16 (164) 3-7/16 (87) 3-5/8 (92) 1-3/8 (35) 2-1/2 (64) 7-1/2 (190) 3/4 (19) 5 (127) 6 (152) 11 (279) 604,605 & 606 1-1/4 6-7/16 (164) 3-7/16 (87) 3-5/8 (92) 1-3/8 (35) 2-1/2 (64) 7-1/2 (190) 3/4 (19) 5 (127) 6 (152) 11 (279
FLANGES Check-Trol™ Isolation Flow Control Flange Description The Check-Trol flange is a combination isolation valve, flow control valve, and companion flange for circulators. The ball valve allows the circulator to be removed from the system without draining the system. The internal spring check prevents gravity circulation. Free floating companion flange makes pump installation a snap.
ISOLATION FLANGES Description The isolation flange is a combination of an isolation ball valve and a companion flange for circulators. The isolation flange allows easy service or replacement of the circulator without the need to drain the system. The isolation flange fits the Bell & Gossett NRF/NBF/SSF wet rotors, Series PL, Series 100, HV, PR and LR circulators.
3 CONTROLS ecocirc e SERIES TIMER ® Description To increase the overall efficiency of a domestic hot water recirculating system and to reduce water wasted while waiting for hot water, the e3 Timer can be installed on all e3 pumps. The timer is easily installed by removing the motor end cap, plugging in the timer and setting the timer schedule without any wiring. The timer can be used in 3-different selections: ON, OFF and TIMER.
RELAYS ZONETROL II AZ-1A™ Snap-On Pump Relay Description The ZONETROL II AZ-1A snap on relay box is an easy to install single zone pump controller that mounts directly on any Bell & Gossett wet rotor circulator NRF/NBF or Series PL booster. The AZ-1A turns the pump and boiler ON as thermostat calls for heat. Using the wire nuts provided with the package, the AZ-1A is quickly assembled onto any NRF/NBF or 1/12 to 1/6 HP Series PL.
RELAYS ZONETROL™ Switching Relays for Zoning with Valves Features • 100% factory tested - guarantees operation • Five year limited warranty - the best in the business • Replaceable, standard “ice cube” type relays allow up to 10 amps, 1/3 HP per individual zone • Selectable priority for domestic hot water • 30 minute built-in priority timer helps prevent house freeze up - no additional plug-in cards required • Automatically resetable fuse protects controller from overload - eliminates “no heat” call back
VALVES Snap Zone™ Valve Description Snap Zone valves are precision engineered four wire thermoelectrically operated valves designed for heating and cooling systems. The valve opens and closes based upon the voltages applied to the actuator. Use the Bell & Gossett Snap Zone Valves to speed installation time and reduce callback times to customers. The actuator can be installed or removed at any angle on the adapter ring.
BALANCE VALVES Lead-Free* Circuit Setter® Plus Description Materials of Construction The Circuit Setter Plus and Circuit Setter Plus RF provide the perfect balance of adjustability and efficiency for potable water and HVAC systems. They are precisely calibrated for use as a presettable balance valve, variable orifice flow meter and positive shut-off service valve. They are also designed for optimal system efficiency and water conservation.
BALANCE VALVES Circuit Sentry Flo-Setter TM Description TM Circuit Sentry Flo-Setter New GPM dial The Circuit Sentry Flo-Setter valve is a field adjustable pressure independent flow limiter that maintains set flow rates regardless of pressure fluctuations in the system; eliminates overflow. • The unique GPM dial is easy to set.
VALVES Flo-Control™ Valves Description Flo-Control valves prevent gravity flow in forced hot water systems, and permit summer/winter operation of indirect water heaters. Features • Combination straight/angle configurations in sizes 3/4” to 2” for ease of installation. • Removable cap allows easy cleaning and service without removing pipe connections. • Manual operating position for vertical lift disc to permit gravity circulation.
VALVES Hydrotrol™ Flow Control Valves Description The Hydrotrol (HT) flow control valve is used to prevent overheating of zones due to gravity flow in hydronic heating systems and will permit summer-winter operation of indirect water heater. The HT valve allows fluid to pass when the system or zone pumps start. When the system or zone pumps are not operating, the HT valve remains closed, preventing gravity circulation.
VALVES Pressure Reducing Valves Description FB-38 Reducing valves fill the system to a preset pressure for optimum performance. • Fast fill feature reduces start-up time and labor. • Low inlet pressure check valve helps prevent loss of system pressure if the supply water drops below system pressure. • Union connection available with 1/2” male NPT thread and 1/2” female sweat tail-piece for fast, flexible system connection.
ACCESSORIES Copper Red Ring Monoflo® Fittings Description Copper Red Ring Monoflo Fittings let you use a single pipe to serve as both supply and return main. Features • Connect risers to the main, assuring proper diversion of water to each heating unit regardless of type and its position in the system. • Recommended for most installations including cast iron non-ferrous base boards, free-standing radiation or convectors.
AIR SEPARATORS EASB-Jr Enhanced Air Separator Description Dimensions & Weights Operating Data Bell & Gossett’s Model EASBMaximum Working Pressure: 150 PSI (10 bar) JR Enhanced Air Separator Maximum Operating Temperature: 250°F (121°C) automatically removes entrained air bubbles in hydronic systems. As Materials of Construction fluid enters the EASB-JR, the velocity is decreased creating a low pressure Body & Cap: Brass area.
HYDRONIC SPECIALTIES RV-125A Readout Valve and RP-250B Readout Probe TB– Thermoflo® Balancer The RV-125A is designed for use wherever pressure tappings are required to monitor flow or pressures. The Readout Valve is fitted with an EPT insert which incorporates a unique check valve feature designed RP-250 RV-125 to check flow when the Readout Valve is not being used to monitor flow. Use companion RP-250B Readout Probes with the RV-125A Readout Valve.
ACCESSORIES PSH - Primary/Secondary Header Description Operating Data The B&G low-loss header, Model PSH, is a combination air separator and manifold that creates independent primary and secondary circuits. The B&G Model PSH is equipped with a purge valve allowing the user to remove any debris deposited on the bottom of the vessel and an air vent releasing trapped air in the system.
TANKS HFT Diaphragm Tanks • Expansion Tanks for Hydronic Heating Description Specifications Bell & Gossett HFT expansion tanks are designed to absorb the force of thermal expansion in hydronic heating systems. Series HFT tanks for hydronic heating systems are available in sizes from 2—86 gallons. The Series HFT tank is designed to absorb the force of thermal expansion of heating water to maintain proper pressurization in a closed hydronic system.
HFT-15 1BN326 HFT-30 1BN327 HFT-60 1BN328 HFT-90 1BN329 HFT-30V 1BN330 HFT-40V 1BN331 HFT-60V 1BN332 Description HFT-90V 1BN333 HFT-110V 1BN334 Bell & Gossett PT expansion tanks are designed to absorb the force of thermal HFT-160V 1BN335 2 (7.5) 4.4 (16.6) 7.6 (28.7) 14 (53) 14 (53) 20 (75.7) 32 (121.1) 44 (166.5) 62 (234.6) 86 (325.5) TANKS PT Diaphragm Tanks Expansion Tanks for Potable Water Systems expansion in domestic potable water systems.
VALVES TPV – Tank Purge Valves Horizontal Tank Installation with Rolairtrol Air Separator Description Combination full port shut-off valve and drain valve used to connect an expansion tank to the system. It is important that the pre-charge in an expansion tank be maintained at the proper pressure at all times. This pressure is the lowest system operating pressure. When the tank’s pressure is adjusted, there should be no system liquid in it.
HEAT EXCHANGERS Brazed Plate Heat Exchangers Description Model BPX brazed plate heat exchangers offer the highest level of thermal efficiency and durability in a compact, low cost unit. The corrugated plate design provides very high heat transfer coefficients, resulting in a more compact design. The unit’s stainless steel plates are vacuum brazed together to form a durable, integral piece that can withstand high pressure and temperature.
BP412-30 (1" MPT) BP412-30 (1" MPT) BP412-50 (1" MPT) BP424-20 (2" MPT) BP424-30 (2" MPT) BP424-40 (2" MPT) BP424-50 (2" MPT) 250,000 300,000 450,000 600,000 900,000 1,200,000 1,350,000 25.8 30.9 46.4 61.8 92.7 123.6 139.1 4.1 5.8 6.2 4.8 4.8 5.1 4.7 17.9 21.4 32.1 42.9 64.3 85.7 96.4 2.1 2.9 3.3 2.8 3.0 3.2 2.9 PL-36 PL-55 613 609 614 625 625 1½" 2" 2" 2" 2½" 3" 3" be a BP400-40. BPDW415-110 (1" MPT) 1,100,000 45.4 ( 2 ) BPDW415-80 (1" MPT) 1,500,000††† 61.
WASTEWATER Submersible Sump Pumps Description Sump pumps are specifically designed for basement draining, dewatering and water transfer. It has a range of capacities up to 70 GPM and maximum heads of 37 TDH ranging from 1/4 HP to 3/4 HP. The stainless steel or cast iron construction is available with 1-1/2” discharge connections. Battery back-up sump pumps also available for emergency back up service in the event of a power outage. SC 6.4” Specifications • Maximum solids 1/2” 9.
N WASTEWATER Submersible Sump Pumps GSP0311 105/9” From Goulds Water Technology Cast Iron Sump Pump 75/9” 101/8” 31/4” Specifications Model Number Part Number GSP GSP0311 GSP Min. Volts Amps Circuit Phase Breaker 1/3 115 10 15A 1 HP GSP0311M 1/3 115 10 15A 1 Float Min. Min. Min. Cord Discharge Switch On Off Basin Length Connection Style Level Level Diameter Vertical 9’ 1-1/2” 7-1/4” 3-1/2” 1’ Not 9’ 1-1/2” — — 1’ Supplied Max.
Genuine Bell & Gossett Parts When replacing parts in your customers’ B&G booster or other hydronic specialties, don’t settle for anything other than genuine B&G parts. You owe it to your customers and to yourself to do it right the first time. Bell & Gossett parts are designed and engineered strictly for the Bell & Gossett boosters. Substitute parts may seem to cost less. But more often than not, they actually cost a lot more, when they do not hold up on the job.
