Overview of Primary Product
DESCRIPTION
BRONZE FITTED
PUMP (STANDARD
CONFIGURATION
ALL IRON PUMP
(OPTIONAL)
11 Shaft Steel SAE 1144 Steel SAE 1144
12 Volute Cast Iron Cast Iron
ASTM #A159 ASTM #A159
13 Impeller Cast Bronze Cast Iron
ASTM #B584 ASTM #A536
14 Shaft Sleeve Bismuth Bronze #304 Stainless Steel
#C89835 ASTM #A312
15 Impeller Key #304 Stainless Steel #304 Stainless Steel
16 Impeller Washer 1510 – Steel Stainless Steel
17 Impeller Lock Washer #304 Stainless Steel #304 Stainless Steel
18 Impeller Cap Screw #304 Stainless Steel #304 Stainless Steel
19 Volute Gasket Cellulose Fiber Cellulose Fiber
10 Seal Assemblies
11 Condition Monitor Stainless Steel Encloser Stainless Steel Encloser
Standard Seal
Bellows Buna N Buna N
Faces Carbon-Ceramic Carbon-Ceramic
Metal Parts Brass Stainless Steel
Spring Stainless Steel Stainless Steel
For Stuffing Box
10A Flushed Single
O-Rings EPR EPR
Faces Carbon-Tungsten Carbon-Tungsten
Carbide Carbide
Metal Parts Stainless Steel Stainless Steel
Spring Stainless Steel Stainless Steel
Packed
Packing Graphited Graphited
Impregnated Teflon Impregnated Teflon
Gland Bronze Cast Iron
Lantern Ring Filled TFE Filled TFE
OPTIONAL FEATURES
All Iron Construction
Bronze Casing Wear Ring
Stainless Steel Shaft Sleeve
Stainless Steel Shaft
Drip Pan
EPR/Tungsten Carbide Seal
(Standard Configuration only)
Stuffing Box Construction with several seal
and packing options
Seal Selection Guide For:
A. Standard Seals
• BUNA-PH Limitations 7-9; Temperature Range
–20°F to +225°F
• EPR-PH Limitations 7-11; Temperature Range
–20°F to +250°F
For use on open or closed clear water systems.
Maximum working pressure 175 psi.
B. Flushed Single Seals (Stuffing Box Design)
• PH Limitations 7-11; Temperature Range
–20°F to +300°F**
For use on closed or open systems where the
temperature or pressure requirements exceed the
limitations of the standard seal. Available in 175 psi,
or 250 psi working pressures.
C. Flushed double Seals (Stuffing Box Design)
PH Limitations 7-9; Temperature Range 0°F to +250°F
For use on closed or open low pressure systems which
may contain a high concentration of abrasives.An external
flush is required. Maximum working pressure 175 psi.
D. Packing (Stuffing Box Design)
PH Limitations 7-9; Temperature Range 0°F to +190°F
For use on open or closed systems which require a large
amount of make-up water, as well as systems which
are subjected to widely varying chemical conditions and
solids buildup.
Materials of Construction
Vent Plug
Volute
Gauge Tapping
Volute Gasket
Shaft
Impeller
Gauge
Tapping
Bronze Casing
Wearing Ring
(Optional)
Impeller Cap Screw
Slinger
Shaft Sleeve
Impeller Key
Impeller Washer
Impeller Lock Washer
Seal Assembly
10
Condition Monitor
11
4
5
6
7
1
9
2
3
Volute
Gauge Tapping
Volute Gasket
Shaft
Impeller
Gauge
Tapping
Bronze Casing
Wearing Ring
(Optional)
Impeller Cap Screw
Drain Plug
Slinger
Shaft Sleeve
Impeller Key
Impeller Washer
Impeller Lock Washer
4
5
6
7
1
9
2
3
Lantern Ring
Packing
Packing Gland
‰
Standard Configuration Optional – S Configuration
** For operating temperatures above 250°F, a cooled flush is required – and is recommended for
temperatures above 225°F for optimum seal life. On closed systems, cooling is accomplished by inserting
a small heat exchanger in the flush line to cool the fluid. Flush-line Filters and Sediment Separators are
available on special request.
Condition Monitor
11
5