Network USB Hub User Manual F5L009
Table of Contents 1. Introduction .....................................................................1 2. Setting Up your Network USB Hub ..................................2 3. Using the Network USB Hub Control Center....................5 4. Appendix – Operation/Compatibility Notes .................... 17 5. Information ....................................................................
Introduction Congratulations and thank you for purchasing the Network USB Hub (the Hub) from Belkin. By connecting to your network router, this innovative sharing tool gives you a great way to enhance its capabilities, as well as those of all the USB devices connected throughout your network. It lets you access your USB devices remotely without the hassle of setting up network software.
Setting Up your Network USB Hub 1 2 3 4 5 The Hub works with Windows® XP and Windows VistaTM (32- and 64-bit), and Mac OS® X (v10.3~v10.4). In order to use the Hub, you must have a networking router connecting your network. 1. Preparing for Setup NOTE: If you are connected to a network router that uses Dynamic Host Configuration Protocol (DHCP), which most networks do, you do not need to set up your Hub. 1.1 Plug the AC adapter into the Hub. 1.2 Check the Power LED (green). It should be illuminated. 1.
Setting Up your Network USB Hub 2.2 You will see the Hub Setup CD screen. Click “Install Control Center”. 1 2 3 4 2.3 You will see the “Welcome” screen. Click “Continue”. 5 2.4 Select a destination in which to install the software and click “Continue”.
Setting Up your Network USB Hub 1 2.5 Click “Install” to start the installation. 2 3 4 5 2.6 If prompted please enter name and password for authentication. 2.7 Installation is complete. Click “Restart”. Warning: Please update your firewall and Internet security software to make sure your computer works properly with the Network USB Hub.
Using the Network USB Hub Control Center Once the setup is completed, launch the Belkin Network USB Hub Control Center through the “Start” menu. The main Control Center (see image below) gives you a visual depiction of your connection configuration. 1 2 3 4 5 You can connect to a device by Ctrl+Clicking the device on the list, or by selecting it on the list, and then clicking “Connect”, on the bottom of the screen.
Using the Network USB Hub Control Center 1 2 What the designations mean Device: Name of the device. You can change the name by clicking “Properties”. Status: Status of the device. The status changes automatically. 3 Type: Category of the device. This is detected automatically. 4 Automatically connect: This allows the PC to automatically connect to this device. This can be enabled or disabled in “Properties”. 5 Hub ID: The ID of the Hub into which the device is plugged. This is detected automatically.
Using the Network USB Hub Control Center 1 Not Connected: The device is being used by someone else and it is not available. You can make a request for the device by clicking “Request Use”. 2 3 4 5 Unavailable: The device has been disconnected from the Hub. It will be removed from the list when you click “Refresh”.
Using the Network USB Hub Control Center 1 Requesting a device when it is being used by someone else 2 3 4 5 When someone else is connected to a device that you want to use, you can make a device request. Ctrl+Click on the device in the list and select “Request Use” from the pop-up menu, or, you can select the device from the list and click “Request Use”.
Using the Network USB Hub Control Center When the other user clicks “Yes”, the device will be disconnected automatically from that user’s computer and it will be available for you to use. Changing the connection settings You can set the Control Center to automatically connect to devices when the software launches. Selecting “Automatically Connect” simplifies the overall experience for most users; however, it may not be a suitable default setting if the devices are shared among many users.
Using the Network USB Hub Control Center 1 2 3 4 5 Click on the “Connection” tab and check or uncheck the box next to “Automatically connect this device when the Control Center starts”, depending on whether or not you want to automatically connect the device on start-up, then click “Apply”.
Using the Network USB Hub Control Center Sharing a USB printer You can set the Network USB Hub Control Center to share any USB printers on the network. Note: You must install the printer driver on your computer before enabling sharing. 1 2 Note: You must install the Network USB Hub Control Center software on each computer that is going to access the printer. 3 1. Install the Network USB Hub and printer software, and driver first. 2. Select the printer from the list and click “Connect”.
Using the Network USB Hub Control Center 1 8. This setting has to be set on all the computers on the network to enable the sharing feature correctly.
Using the Network USB Hub Control Center Changing the Network USB Hub Control Center settings 1 2 3 4 5 Click the “General” link, under “Common Tasks” on the left of the “Control Center” screen to open the “Network USB Hub settings” window.
Using the Network USB Hub Control Center 1 2 3 4 5 Simply check or uncheck the box to determine whether you want to launch the Network USB Hub Control Center when MAC OS starts. Checking “Show the Hub Control Center” causes the “Control Center” screen to display when you launch the Control Center.
Using the Network USB Hub Control Center Accessing the Network USB Hub hardware setting 1 2 3 4 5 Click the “Network USB Hubs” link, under “Common Tasks”, on the left side of the “Control Center” screen to open the “Network USB Hub settings” window.
Using the Network USB Hub Control Center 1 2 3 4 5 Select and click the Network USB Hub from the list. Then click “Properties”. Your web browser will launch and open the web page built into the Network USB Hub. From there, you can change the advanced network settings and update the firmware for the Network USB Hub. The password for the web page is blank or none by default.
Appendix – Operation/Compatibility Notes Certain USB devices may not be compatible with the Hub. Since the Network USB Hub uses virtual network technology, some USB devices (e.g., TV tuners, webcams, and USB audio devices) are not compatible with it in Mac OS. They will not appear on the Control Center even when they are attached to the Network USB Hub. WLAN connection The Network USB Hub’s virtual network technology may not work properly if the WLAN connection is interrupted.
Information 1 2 3 4 5 FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin International, Inc., of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product: F5L009 to which this declaration relates: Complies with Part 15 of the FCC Rules.
Information altered in any way, or tampered with. The Belkin Product Warranty does not protect against acts of God such as flood, lightning, earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low voltage disturbances (i.e. brownouts or sags), non-authorized program, or system equipment modification or alteration. How to get service. To get service for your Belkin product you must take the following steps: 1. Contact Belkin International, Inc.
Information 1 2 USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other damages, so the above limitations may not apply to you. 3 4 For information on product disposal please refer to http://environmental.belkin.
Information Free Tech Support* *National call rates may apply www.belkin.com You can find additional support information on our website www.belkin. com through the tech-support area. If you want to contact technical support by phone, please call the number you need from the list below*. COUNTRY NUMBER INTERNET ADRESS AUSTRIA 0820 200766 www.belkin.com/uk/networking/ BELGIUM 07 07 00 073 www.belkin.com/nl/networking/ CZECH REPUBLIC 239 000 406 www.belkin.
Network USB Hub Belkin Tech Support UK: 0845 607 77 87 Europe: www.belkin.com/support Belkin Ltd. Express Business Park Shipton Way, Rushden NN10 6GL, United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin SAS 130 rue de Silly 92100 Boulogne-Billancourt, France +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax Belkin GmbH Hanebergstrasse 2 80637 Munich Germany +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin Iberia C/ Anabel Segura, 10 planta baja, Of.
