N+ Wireless Router User Manual PM00736 F5D8235-4
Table of Contents Table of Contents sections 1 2 3 4 1 Introduction ���������������������������������������������������������������������������������������� 1 5 6 7 8 9 10 WEP Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Access Point Mode . . . . . . . .
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Thank you for purchasing the Belkin N+ Wireless Router (the Router). Following are two short sections—the first discusses the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and performance.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Revolutionary N+ Wireless Technology with MIMO (N MIMO) Placement of your N+ Wireless Router Your Belkin N+ Wireless Router uses a new smart-antenna technology called Multiple Input Multiple Output (MIMO). N MIMO complies with the IEEE draft 802.11n specification. It increases speed, range, reliability, and spectral efficiency for wireless networking systems.
Introduction Table of Contents sections 1 2 3 4 1. Router Placement 6 7 8 9 10 If your wireless signal seems weak in some spots, make sure that objects such as these are not blocking the signal’s path (between your computers and Router). Place your Router, the central connection point of your network, as close as possible to the center of your wireless network devices. To achieve the best wireless network coverage for your “wireless clients” (i.e.
Introduction Table of Contents sections 1 2 3 4 5 6 7 8 9 10 4. Choose the “Quietest” Channel for your Wireless Network 5. Secure Connections, VPNs, and AOL In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours. Secure connections typically require a user name and password, and are used where security is important.
Product Overview Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Product Features Web-Based Advanced User Interface In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin N+ Wireless Router an ideal solution for your home or small office network. You can set up the Router’s advanced functions easily through your web browser, without having to install additional software onto the computer.
Product Overview Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Universal Plug and Play (UPnP) Integrated N+ Wireless Access Point UPnP is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. N MIMO is an exciting new wireless technology based on the draft IEEE 802.11n specification. It employs MIMO (Multiple Input Multiple Output) smart-antenna technology that achieves data rates of up to 300Mbps.
Knowing your Router Table of Contents sections 1 2 3 4 Package Contents • • • • • • • • 5 6 Belkin N+ Wireless Router Quick Installation Guide Belkin Setup Assistant Software CD RJ45 Ethernet Networking Cable Power Supply User Manual on the Setup Assistant CD Network Status Display Guide Wireless Security Setup Guide (A) • • • • Broadband Internet connection such as a cable or DSL modem with RJ45 (Ethernet) connection At least one computer with an installed network interface adapter TCP/IP netwo
Knowing your Router Table of Contents sections 1 2 3 4 A. Broadband Download Speedometer These lights will display a graphic representation of the current download speed being transferred through the Internet connection. The speed will be measured on the speedometer against the fastest speed that has been measured by the N+ since being activated. These lights will display a graphic representation of the current download speed being transferred through the Internet connection.
Knowing your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 G. Router/Power Status J. Internet Status When you apply power to the Router or restart it, a short period of time elapses while the Router boots up. During this time, the “router” icon blinks. When the Router has completely booted up, the “router” icon becomes a solid light, indicating the Router is ready for use. This unique icon shows you when the Router is connected to the Internet.
Knowing your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 K. Connections to Wired Computers ii. Restoring the Factory Defaults Connect your wired (non-wireless) computers to these ports. These ports are RJ45, 10/100/1000 auto-negotiation, auto-uplinking ports for standard UTP category 5 or 6 Ethernet cable. The ports are labeled 1 through 4. Press and hold the “Reset” button for at least 10 seconds, then release it. The lights on the Router will momentarily flash.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Verify the contents of your box.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 1: Hardware Connections 4 WAN 3 LAN 3 1 2 1 3 1. Find the cable connecting your modem and computer*. Unplug it from the computer and plug it into the yellow port on the Belkin Router. 2. Connect the new cable (provided in the box) to any gray port on the Router. Plug the other end into a network (Ethernet) port on your computer. 3.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 2: Set Up the Router – Run the Setup Assistant Software A. Shut down any programs that are running on your computer at this time. Turn off any firewall or Internet-connection-sharing software on your computer. B. Insert the CD into your computer. The Setup Assistant will automatically appear on your computer’s screen within 15 seconds. Click on “Go” to run the Setup Assistant.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Select Country Confirmation Screen Select your country from the drop-down box. Click “Begin” to continue. Verify that you have completed all QIG steps by checking the box to the right of the arrow. Click “Next” to continue.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Progress Screen 1.1 Checking Settings Setup Assistant will show you a progress screen each time a step in the setup has been completed. The Setup Assistant will now examine your computer’s network settings and gather information needed to complete the Router’s connection to the Internet.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1.2 Verifying Hardware Connections 1.3 Naming your Wireless Network The Setup Assistant will now verify your hardware connection. The Setup Assistant will display the default wireless network name or Service Set Identifier (SSID). This is the name of your wireless network to which your computers or devices with wireless network adapters will connect.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1.4 Requesting Internet Account Info (if needed) 1.5 Configuring the Router If your Internet account requires a login and password, you will be prompted with a screen similar to the illustration below. Select your country or ISP from the drop-down boxes. The Setup Assistant will now configure your Router by sending data to the Router and restarting it. Wait for the on-screen instructions.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 1.6 Checking Internet Connection Congratulations We are almost done. The Setup Assistant will now check your connection to the Internet. You have finished installing your new Belkin Router. You will see the Congratulations screen when your Router can connect to the Internet. You can begin surfing by opening your browser and going to any website.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Troubleshooting 1.7 Optional: Assistance Connecting Other Computers If the Setup Assistant is not able to connect to the Internet, you will see the following screen. Follow the on-screen instructions to go through the troubleshooting steps. This optional step will help you to connect additional wired and wireless computers to your network. Follow the on-screen instructions.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Congratulations Storage Manager Once you have verified that your other wired and wireless computers are properly connected, your network is set up and working. You can now surf the Internet. Click “Next” to take you back to the main menu. The Storage Manager is an application that provides easy access to your USB storage device. Once this is installed, your storage device will appear as a drive letter (e.g.
Connecting and Configuring your Router Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Storage Manager also allows you to safely eject the storage device before unplugging it from your Router. This is recommended before unplugging the USB storage device as there might be another user on your network who is accessing the drive. Simply right-click on the “Storage Manager” icon in the system tray and select the appropriate button.
Alternate Setup Method Table of Contents sections 1 2 3 4 Step 1: Hardware Connections – Follow the Quick Installation Guide 5 6 7 8 9 10 Logging into the Router You will see the Router’s home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Router’s settings, you have to log in. Clicking the “Login” button or clicking on any one of the links on the home page will take you to the login screen.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Understanding the Web-Based Advanced User Interface The home page is the first page you will see when you access the Advanced User Interface (UI). The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page.
Alternate Setup Method Table of Contents 1. sections 1 2 3 4 Quick-Navigation Links 7 8 9 10 This indicator is visible in all pages of the Router, indicating the connection status of the Router. When the indicator says “Connected” in blue, the Router is connected to the Internet. When the Router is not connected to the Internet, the indicator will read “No Connection” in RED. The indicator is automatically updated when you make changes to the settings of the Router. Home Button 5.
Alternate Setup Method Table of Contents 7. sections 1 2 3 4 Version Info 7 8 9 10 Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the links or by clicking on the “Internet/WAN” quicknavigation link on the left side of the screen. 8. LAN Settings 11. Router Status The “Help” button gives you access to the Router’s help pages.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Step 4 Configuring your Router for Connection to your Internet Service Provider (ISP) Setting your Connection Type The “Internet/WAN” tab is where you will set up your Router to connect to your Internet Service Provider (ISP). The Router is capable of connecting to virtually any ISP’s system provided you have correctly configured the Router’s settings for your ISP’s connection type.
Alternate Setup Method sections Table of Contents 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP A dynamic connection type is the most common connection type found with cable modems. Setting the connection type to “dynamic” in many cases is enough to complete the connection to your ISP. Some dynamic connection types may require a host name. You can enter your host name in the space provided if you were assigned one.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Static IP A static IP address connection type is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP or on the paperwork that your ISP left with you. Type in your information, then click “Apply Changes” (4).
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your ISP Connection Type to PPPoE Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet connection in your home or small office that doesn’t require a modem, you may also use PPPoE. 1. User Name This space is provided to type in your user name that was assigned by your ISP. 2.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Internet Service Provider (ISP) Connection Type to Point-to-Point Tunneling Protocol (PPTP) [European Countries Only]. Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries. This sets up a direct connection to the ISP’s system. Type in the information provided by your ISP in the space provided. When you have finished, click “Apply Changes” (9).
Alternate Setup Method Table of Contents 1. sections 1 2 3 4 PPTP Account 5 6. 6 7 8 10 My Subnet Mask Provided by your ISP. Enter your PPTP account name here. Provided by your ISP. Enter the IP address here. 2. 7. Default Gateway PPTP Password 9 Type in your password and retype it into the “Retype Password” box to confirm it. Provided by your ISP. If your ISP did not give you a connection ID (default gateway), leave this blank. 3. 8.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting your Connection Type if You Are a Telstra® BigPond User [Australia Only] Your user name and password are provided to you by Telstra BigPond. Enter this information below. Choosing your state from the drop-down menu (1) will automatically fill in your login server IP address.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting Custom Domain Name Server (DNS) Settings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Locaters (URLs) like “www.belkin.com” to IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address.
Alternate Setup Method Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring your WAN Media Access Controller (MAC) Address Entering a Specific MAC Address All network components including cards, adapters, and routers, have a unique “serial number” called a MAC address. Your Internet Service Provider (ISP) may record the MAC address of your computer’s adapter and only let that particular computer connect to the Internet service.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Viewing the LAN Settings Changing LAN Settings Clicking on the header of the LAN tab (1) will take you to the LAN tab’s header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on “LAN Settings” (2) or to view the list of connected computers, click on “DHCP client list” (3).
Using the Web-Based Advanced User Interface Table of Contents 1. sections 1 2 3 4 IP Address 5 4. The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click “Apply Changes”. The IP address you choose should be a non-routable IP.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Viewing the DHCP Client List Page You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computer’s network interface card (NIC).
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring the Wireless Network Settings The “Wireless” tab lets you make changes to the wireless network settings. From this tab you can make changes to the wireless network name or Service Set Identifier (SSID), operating channel, encryption security settings, and configure the Router to be used as an access point.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing the Wireless Channel 2. There are a number of operating channels from which you can choose— in the United States, there are 11 and in the United Kingdom (and most of Europe), there are 13. In a small number of other countries, there are other channel requirements. Your Router is configured to operate on the proper channels for the country in which you reside.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Using the Bandwidth Switch 5 6 7 8 9 10 This switch allows you to set the Router’s wireless bandwidth modes. There are several modes available: immediate. Each computer now needs to be set to connect to your specific SSID; an SSID of “ANY” will no longer be accepted. Refer to the documentation of your wireless network adapter for information on making this change. 1.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Changing the Wireless Security Settings 6 7 8 9 10 PIN: The client device has an 8-digit PIN number that is associated with WPS. Enable WPS through the screen illustrated below. Enter the client’s PIN into the Router’s internal registrar (accessed through this screen). The client will be automatically enrolled into your wireless network within two minutes.
Using the Web-Based Advanced User Interface Table of Contents 1. sections 1 2 3 4 Wi-Fi Protected Setup (WPS) 5 6 7 8 9 10 WPA2 Requirements Enabled or Disabled. 2. IMPORTANT: In order to use WPA2 security, all your computers and wireless client adapters must be upgraded with patches, driver, and client utility software that supported WPA2. At the time of this User Manual’s publication, a couple security patches are available, for free download, from Microsoft®.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WPA/WPA2-Personal (PSK) Like WPA security, WPA2 is available in both WPA2-Personal (PSK) mode and WPA2-Enterprise (RADIUS) mode. Typically, WPA2-Personal (PSK) is the mode that will be used in a home environment, while WPA2Enterprise (RADIUS) is implemented in a business environment where an external radius server distributes the network key to the clients automatically.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Setting WEP Encryption Using a Hexadecimal Key Note to Mac users: The “Passphrase” option will not operate with Apple® AirPort®. To configure encryption for your Mac computer, set the encryption using the manual method described in the next section. A hexadecimal key is a mixture of numbers and letters from A–F and 0–9. 64-bit keys are 10 digits long and can be divided into five two-digit numbers.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Guest Access: This option allows guest users access to the Internet while keeping them away from your private network. By default, this option is enabled. Guest users should connect to the Belkin N+ Guest network. 5 6 7 8 9 10 Security options for Guest Access: Hotel Style: Users will be redirected to a hotel-style landing page when they first try to access the Internet.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Using the Access Point Mode Note: This advanced feature should be employed by advanced users only. The Router can be configured to work as a wireless network access point. Using this mode will defeat the NAT IP sharing feature and DHCP server. In AP mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network that you will bridge to. The default IP address is 192.168.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Configuring the Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including: • IP Spoofing • Land Attack Ping of Death (PoD) • Denial of Service (DoS) • IP with zero length • Smurf Attack • TCP Null Scan • SYN flood • UDP flooding • Tear Drop Attack • ICMP defect • RIP defect • Fragment flooding The firewall also masks common po
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Configuring Internal Forwarding Settings Choosing an Application The Virtual Servers function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Access Control The Router can be configured to restrict access to the Internet, email, or other network services at specific days and times. Restriction can be set for a single computer, a range of computers, or multiple computers. Select the “Enable” radio button to use this feature. To restrict Internet access to a single computer, for example, click the “Add” button and select the appropriate entry.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 The Access Control rule can be removed by clicking the “Delete” button. Click on the entry number for the configuration options. 5 6 7 8 9 10 There are four main configurations for Access Control lists. The first one is “Schedule” for that rule. The second is “Service” for the services to be blocked for that rule.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Enabling the Demilitarized Zone (DMZ) The DMZ feature allows you to specify one computer on your network to be placed outside of the firewall. This may be necessary if the firewall is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is NOT protected from hacker attacks.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Using Dynamic DNS The Dynamic DNS SM service is ideal for a home website, file server, or to make it easy to access your home PC and stored files while you’re at work. Using the service can ensure that your host name always points to your IP address, no matter how often your ISP changes it. When your IP address changes, your friends and associates can always locate you by visiting yourname.dyndns.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Blocking an ICMP Ping Security Log Computer hackers use what is known as “pinging” to find potential victims on the Internet. By pinging a specific IP address and receiving a response from the IP address, a hacker can determine that something of interest might be there. The Router can be set up so it will not respond to an ICMP ping from the outside. This heightens your Router’s security level.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 Restarting the Router Restarting the Router to Restore Normal Operation Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings. 1. 10 Click the “Restart Router” button. 2. The following message will appear. Click “OK”. 3. The following message will appear.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 Restoring Factory Default Settings 1. Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults. 2. The following message will appear. Click “OK”. 9 10 Click the “Restore Defaults” button. 3. The following message will appear.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Saving a Current Configuration You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. 2. A window will open that allows you to select the location where you want to save the configuration file.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Restoring a Previous Configuration 1. This option will allow you to restore a previously saved configuration. N+ Wireless Router 5 57 6 7 8 9 10 Click “Browse”. A window will open that allows you to select the location of the configuration file. All configuration files end with a “.conf”. Locate the configuration file you want to restore and doubleclick on it.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 2. You will be asked if you want to continue. Click “OK”. 6 7 8 9 10 4. A 60-second countdown will appear on the screen. When the countdown reaches zero, the Router’s configuration will be restored. The Router’s home page should appear automatically. If not, type in the Router’s address (default = 192.168.2.1) into the navigation bar of your browser. 3. A reminder window will appear.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Updating the Firmware Checking for a New Version of Firmware From time to time, Belkin may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Router’s firmware to the latest version.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Downloading a New Version of Firmware 1. To download the new version of firmware, click “Download”. If you click the “Check Firmware” button and a new version of firmware is available, you will see a screen similar to the one on the right: 2. A window will open that allows you to select the location where you want to save the firmware file. Select a location.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Updating the Router’s Firmware 1. In the “Firmware Update” page, click “Browse”. A window will open that allows you to select the location of the firmware update file. N+ Wireless Router 61 5 6 7 8 9 10 2. Browse to the firmware file you downloaded. Select the file by double-clicking on the file name. 3. The “Update Firmware” box will now display the location and name of the firmware file you just selected.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4. You will be asked if you are sure you want to continue. Click “OK”. 5. You will see one more message. This message tells you that the Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted. Click “OK”. N+ Wireless Router 4 5 6. 62 6 7 8 9 10 A 60-second countdown will appear on the screen.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Changing System Settings Setting the Time and Time Zone The “System Settings” page is where you can enter a new administrator password, set the time zone, or enable remote management. The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server. This allows the Router to synchronize the system clock to the global Internet.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Enabling Remote Management Enabling/Disabling UPnP Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Router’s settings from anywhere on the Internet. There are two methods of remotely managing the Router.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Enabling/Disabling Auto Firmware Update 6 7 8 9 10 ECO Mode: This option allows you to turn off the wireless radio automatically at set periods of time in order to save power. Click the check box to turn off the radio at the times shown in the drop-down boxes.
Using the Web-Based Advanced User Interface Table of Contents sections 1 2 3 4 Manually Configuring Network Settings 5 6 7 8 9 10 3. Next to “Configure” (2), if “Manually” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router). 4. If not already set, at “Configure:”, choose “Using DHCP Server”.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 Manually Configuring Network Settings in Mac OS X 1. 5 3. 6 7 8 9 10 Select “Built-in Ethernet” (2) next to “Show” in the Network menu. Click on the “System Preferences” icon. (2) (3) (4) (5) 2. Select “Network” (1) from the “System Preferences” menu. (1) N+ Wireless Router 4. 67 Select the “TCP/IP” tab (3). Next to “Configure” (4), you should see “Manually” or “Using DHCP”.
Manually Configuring Network Settings Table of Contents sections 1 2 3 5. If “Manually” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 6. If not already selected, select “Using DHCP” next to “Configure” (4), then click “Apply Now”. 4 Your network settings are now configured for use with the Router.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Manually Configuring Network Settings in Windows 2000, NT, or XP 1. Click “Start”, “Settings”, then “Control Panel”. 2. Double-click on the “Network and dial-up connections” icon (Windows 2000) or the “Network” icon (Windows XP). 3. Right-click on the “Local Area Connection” associated with your network adapter and select “Properties” from the drop-down menu. 4.
Manually Configuring Network Settings Table of Contents sections 1 2 3 4 Manually Configuring Network Settings in Windows 98 or Me 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu. 2. Select “TCP/IP -> settings” for your installed network adapter. You will see the following window (2) (1) (3) 5 6 7 8 9 10 3. If “Specify and IP address” is selected, your Router will need to be set up for a static IP connection type.
Recommended Web Browser Settings Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the WebBased Advanced User Interface, then change your browser’s settings to the recommended settings in this section. 2. Microsoft® Internet Explorer 4.0 or Higher 1. Start your web browser. Select “Tools” then “Internet Options”.
Recommended Web Browser Settings Table of Contents sections 1 2 3 3. Under the “Internet Options” screen, click on “Connections” and select “LAN Settings…”. 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. N+ Wireless Router 4 5 6 7 8 9 10 Netscape® Navigator® 4.0 or Higher 72 1. Start Netscape.
Troubleshooting Table of Contents sections 1 2 3 4 Troubleshooting 5 2. Next, double-click on the CD-ROM drive that the Setup Assistant CD has been placed in to start the installation. 3. The Setup Assistant should start within a few seconds. If, instead, a window appears showing the files on the CD, double-click on the icon labeled “SetupAssistant”. 4.
Troubleshooting Table of Contents sections 1 2 3 4 Setup Assistant cannot connect my Router to the Internet. 5 Use the troubleshooting suggestions within the Setup Assistant. 2. If your ISP requires a user name and password, make sure that you have typed in your user name and password correctly. Some user names require that the ISP’s domain may be at the end of the name. Example: “myname@myisp.com”. The “@myisp.com” part of the user name may need to be typed as well as your user name.
Troubleshooting Table of Contents 4. sections 1 2 3 4 5 6 7 8 9 10 I can’t connect to the Internet wirelessly. You may need to configure your Router to meet the specific requirements of your ISP. To search our knowledge base for ISPspecific issues, go to: http://web.belkin.com/support and type in “ISP”.
Troubleshooting Table of Contents sections 1 2 3 4 I can’t connect to the Internet wirelessly, but my network name is listed. 5 6 7 8 9 10 If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support. If the name of your network is listed in the “Available Networks” list, please follow the steps below to connect wirelessly: 1. Click on the correct network name in the “Available Networks” list.
Troubleshooting Table of Contents sections 1 2 3 4 Limiting the wireless transmit rate—Limiting the wireless transmit rate can help improve the maximum wireless range and connection stability. Most wireless cards have the ability to limit the transmission rate. To change this property, go to the Windows Control Panel, open “Network Connections” and double-click on your wireless card’s connection.
Troubleshooting Table of Contents sections 1 2 3 4 I am having difficulty setting up Wired Equivalent Privacy (WEP) security on a Belkin client card. Double-click the Signal Indicator icon to bring up the “Wireless Network” screen. 2. The “Advanced” button will allow you to view and configure more options of your card. 3. Once the “Advanced” button is clicked, the Belkin Wireless LAN Utility will appear.
Troubleshooting Table of Contents sections 1 2 3 4 I am having difficulty setting up Wireless Protected Access (WPA) security on my Belkin Router for a home network. 1. From the “Security Mode” drop-down menu, select “WPA-PSK (no server)”. 2. For “Encryption Technique”, select “TKIP” or “AES”. This setting will have to be identical on the clients that you set up. 3. 4.
Troubleshooting Table of Contents sections 1 2 3 4 I am NOT using a Belkin client card for a home network and I am having difficulty setting up Wireless Protected Access (WPA) security. 5 4. If you are not using a Belkin Wireless Desktop or Wireless Notebook Network Card that is not equipped with WPA-enabled software, a file from Microsoft called “Windows XP Support Patch for Wireless Protected Access” is available for free download.
Troubleshooting Table of Contents sections 1 2 3 4 What’s the difference between 802.11g and draft 802.11n? 5 6 7 8 9 10 Belkin Wireless Comparison Chart Currently there are three commonly used wireless networking standards, which transmit data at very different maximum speeds. Each is based on the designation for certifying network standards. The most common wireless networking standard, 802.11g, can transmit information up to 54Mbps; 802.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Technical Support Information You can find technical support information at http://www.belkin.com/ networking or www.belkin.com through the tech support area. If you want to contact technical support by phone, please call: FCC Statement US: 877-736-5771 We, Belkin International, Inc.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Caution: Exposure to Radio Frequency Radiation. which the receiver is connected. The device shall be used in such a manner that the potential for human contact normal operation is minimized. • Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Information Table of Contents sections 1 2 3 4 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Information Table of Contents sections 1 2 3 4 5 6 7 8 9 10 Belkin International, Inc., Limited 1-Year Product Warranty What this warranty covers. Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this Belkin product that the product shall be free of defects in design, assembly, material, or workmanship.
Information Table of Contents sections 1 2 3 4 Belkin reserves the right to review the damaged Belkin product. All costs of shipping the Belkin product to Belkin for inspection shall be borne solely by the purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an equipment repair facility to inspect and estimate the cost to repair such equipment.
Belkin International, Inc. 501 West Walnut Street Los Angeles, CA 90220, USA 310-898-1100 310-898-1111 fax Belkin Ltd. Express Business Park, Shipton Way Rushden, NN10 6GL, United Kingdom +44 (0) 1933 35 2000 +44 (0) 1933 31 2000 fax Belkin B.V. Boeing Avenue 333 1119 PH Schiphol-Rijk, The Netherlands +31 (0) 20 654 7300 +31 (0) 20 654 7349 fax Belkin Ltd. 4 Pioneer Avenue Tuggerah Business Park Tuggerah, NSW 2259, Australia +61 (0) 2 4350 4600 +61 (0) 2 4350 4700 fax © 2008 Belkin International, Inc.
