Brochure
Table Of Contents
- DamperTech_2010 381
- DamperTech_2010 382
- DamperTech_2010 383
- DamperTech_2010 384
- DamperTech_2010 385
- DamperTech_2010 386
- DamperTech_2010 387
- DamperTech_2010 388
- DamperTech_2010 389
- DamperTech_2010 390
- DamperTech_2010 391
- DamperTech_2010 392
- DamperTech_2010 393
- DamperTech_2010 394
- DamperTech_2010 396
- DamperTech_2010 397
- DamperTech_2010 398
- DamperTech_2010 399
- DamperTech_2010 400
- DamperTech_2010 401
- DamperTech_2010 402
- DamperTech_2010 403
- DamperTech_2010 404
- DamperTech_2010 405
- DamperTech_2010 406
- DamperTech_2010 407
- DamperTech_2010 408
- DamperTech_2010 409
- DamperTech_2010 410
- DamperTech_2010 411
- DamperTech_2010 412
- DamperTech_2010 413
- DamperTech_2010 414
- DamperTech_2010 415
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA
41
5
1. The damper operating shaft should extend approximately 1-1
/
2 inches from
the damper assembly or duct side. Mount the drive shaft/coupler
➀
to the
damper operating sha
f
t
➁
. Fasten the coupler to the damper operating sha
f
t
b
y tightening the two 3
/
8 inch square head set screws
➂
.
2. Determine the housing mounting orientation
f
or the application.
3. Locate the housing hole position(s) for the control wiring of the actuator.
4
. Make the necessary holes in the housing for the electrical fi ttings. All fi ttings
must be rated for use in NEMA 4X applications.
5
. Install (if ordered with) the 2 mounting brackets
➃
to the housing using the
four 1/4-20 screws, washers, and nuts
➄
.
Do not tighten.
6. Carefully slide the housing over the drive shaft
.
7. Place the housing in the desired mounting position. Trans
f
er the mounting hole
l
ocations
f
rom the mounting bracket to the mounting sur
f
ace
.
8. Drill the 4 holes and
f
asten the brackets to the sur
f
ace.
9. Install the anti-rotation strap to the housin
g
in the correct location
f
or the actua-
tor w
hi
c
h
i
s
b
e
i
ng use
d
.
1
0. Mount the actuator to the drive sha
f
t using the instructions
f
or the actuator be
-
i
ng used. Finger tighten the nuts of the universal clamp. Make sure the back of
the actuator is parallel to the back o
f
the housing
.
1
1. The operating shaft must pass through the mounting clamp at least 3/8 of an
i
nch. It must not extend beyond the front of the housing. Slide the actuator/
h
ousing assembly in the mounting brackets to obtain the proper position
.
1
2. Ti
g
hten the mountin
g
brackets to the housin
g
. Verify that the back of the actua-
tor is still parallel to the back of the housing. Tighten the nuts on the universal
c
lamp.
1
3. Make all of the required electrical connections
.
1
4. Test the actuator/damper operation
.
1
5. Fasten the housin
g
cover
➅
usin
g
the 6 swivel clamps
.
Z
S
-300 Mountin
g
Instructions
ZS-300
(
-1, -5
)
NEMA 4X
,
stainless steel
,
corrosion resistant enclosures for AM
,
GM
,
NFB
,
NFX
,
AFB
,
AFX and AF actuator
s
LF
AMB
GMB
GM
AF/NF
FM/SF
Anti-Rotation Strap Mounting Locations
1
2
3
4
5
6
Inner plate,
see detail below.
Swivel clamps (6)
AMB(X)
LF
AM/SM
GMB(X)
GM
AF/NF
FM/SF
*
*AFB, AFX, NFB and NFX can be installed using GM mounting location without the need of the Z-AF retrofit bracket
.
M40024 - 05/10 - Subject to change. © Belimo Aircontrols (USA), Inc.