Belgacom b-box Instructions for use Version 1.
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION .............................................................................4 About the Belgacom b-box ............................................................................................. 4 Telephony over IP........................................................................................................... 4 CHAPTER 2 INSTALLATION ...............................................................................6 Package Contents .......................
Clone MAC Address................................................................................................. 35 LAN .............................................................................................................................. 36 Wireless......................................................................................................................... 38 Wireless Settings.......................................................................................................
CHAPTER 1 INTRODUCTION Congratulations on your purchase of the Belgacom b-box. We are proud to provide you with a powerful yet simple communication device for connecting your local area network (LAN) to the Internet. For those who want to surf the Internet in the most secure way, this router provides a convenient and powerful solution.
Safety Precautions • Do not expose the product to excessive moisture, rain, sand or heat sources. • The product should not be exposed to dripping or splashing. No object filled with liquids, such as vases, should be placed on the product. • Keep the product away from domestic heating equipment and direct sunlight. • Allow a sufficient amount of free space all around the product for adequate ventilation. • Do not open this product. Contact your retailer if you experience technical difficulties.
CHAPTER 2 INSTALLATION Before installing the Belgacom b-box, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local distributor. Also be sure that you have all the necessary cabling before installing the Belgacom b-box. After installing the Belgacom b-box, refer to “Configuring the Belgacom bbox”.
Data passing between devices connected to your local area network can run at up to 100 Mbps over the four Fast Ethernet ports. The Belgacom b-box connections are described in the following figure and table. f Item ADSL Port LAN Ports TV Ports Reset Button Power Inlet FXS Ports Description Blue ADSL port (RJ-11). Connect your ADSL line to this port. Yellow Fast Ethernet ports (RJ-45). Connect devices on your local area network to these ports (i.e., a PC or switch). Grey Fast Ethernet ports (RJ-45).
Hardware Installation ADSL Connection Connect your ADSL line to this port. Fast Ethernet Connection Connect a PC to one of the RJ-45 ports on the Belgacom b-box with the provided network cable. When inserting an RJ-45 plug, be sure the tab on the plug clicks into position to ensure that it is properly seated. The LAN ports are dual-speed RJ-45 ports. They support auto-negotiation, so the optimum communication mode (half or full duplex) and data rate (10 Mbps or 100 Mbps) are selected automatically.
Attach to Your Network Using Ethernet Cabling The LAN ports on the Belgacom b-box auto-negotiates the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex. Use twisted-pair cabling to connect any of the LAN ports on the Belgacom b-box to an Ethernet adapter on your PC. Otherwise, cascade the LAN port on the Belgacom b-box to an Ethernet hub or switch, and then connect your PC or other network equipment to the hub or switch.
CHAPTER 3 CONFIGURING THE CLIENT PC After completing hardware setup by connecting all your network devices, you need to configure your computer to connect to the Belgacom b-box. First determine how your ISP issues your IP address. Many ISPs issue these numbers automatically using Dynamic Host Configuration Protocol (DHCP). Other ISPs provide a static IP address and associated numbers, which you must enter manually. How your ISP assigns your IP address determines how you need to configure your computer.
1. Double-click Internet Protocol (TCP/IP). 2. If “Obtain an IP address automatically” and “Obtain DNS server address automatically” are already selected, your computer is already configured for DHCP. If not, select these options. Click Cancel to close each window.
Obtain IP Settings From Your Belgacom b-box Now that you have configured your computer to connect to your Belgacom b-box, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Belgacom b-box, you can verify that you have configured your computer correctly. 1. On the Windows desktop, click Start/Programs/ Accessories/Command Prompt. 2. key. In the Command Prompt window, type “IPCONFIG /RELEASE” and press the ENTER 1.
Manual IP Configuration 1. Follow steps 1-4 in “DHCP IP Configuration” on page 3-3. 2. Select “Use the following IP address automatically.” Enter an IP address based on the default network 192.168.1.x (where x is between 2 and 254), use 255.255.255.0 for the subnet mask and the IP address of the Belgacom b-box (default: 192.168.1.1) for the Default gateway field. 3. Select “Use the following DNS server addresses.” 4. Enter the IP address for the Belgacom b-box in the Preferred DNS server field.
• • • • • In the Control Panel window, click Network and Internet Connections. The Network Connections window will open. Locate and double-click the Local Area Connection icon for the Ethernet adapter that is connected to the Belgacom b-box. In the connection status screen, click Properties. Double-click Internet Protocol (TCP/IP). If “Obtain an IP address automatically” and “Obtain DNS server address automatically” are already selected, your computer is already configured for DHCP.
3-10 Obtain IP Settings from Your Belgacom b-box Now that you have configured your computer to connect to your Belgacom b-box, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Belgacom b-box, you can verify that you have configured your computer correctly. 1. 2. key. On the Windows desktop, click Start/Programs/Accessories/ Command Prompt.
3. Type “IPCONFIG /RENEW” and press the ENTER key. Verify that your IP Address is now 192.168.1.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.1.1. These values confirm that your Belgacom b-box is functioning. Type “EXIT” and press the ENTER key to close the Command Prompt window. Your computer is now configured to connect to the Belgacom b-box. Manual IP Configuration 1. Follow steps 1-5 in “DHCP IP Configuration” on page 3-9. 2. Select “Use the following IP Address.
TCP/IP Configuration Setting IP Address ____.____.____.____ Subnet Mask ____.____.____.____ Preferred DNS Server ____.____.____.____ Alternate DNS Server ____.____.____.____ Default Gateway ____.____.____.____ Disable HTTP Proxy You need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your browser can view the Belgacom b-box’s HTML configuration pages. Your computer is now configured to connect to the Belgacom b-box.
Double-click the Network icon in the Systems Preferences window. If “Using DHCP Server” is already selected in the Configure field, your computer is already configured for DHCP. If not, select this Option. Your new settings are shown in the TCP/IP tab. Verify that your IP Address is now 192.168.1.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.1.1. These values confirm that your Belgacom b-box is functioning. Close the Network window.
In the Internet Explorer Preferences window, under Network, select Proxies. Uncheck all check boxes and click OK.
CHAPTER 4 CONFIGURING THE BELGACOM BBOX After you have configured TCP/IP on a client computer, use a web browser to configure the Belgacom b-box. The Belgacom b-box can be configured by any Java-supported browser such as Internet Explorer 4.0 or above. Using the web management interface, you may configure the Belgacom b-box and view statistics to monitor network activity. To access the Belgacom b-box’s management interface, enter the IP address of the Belgacom bbox in your web browser: http://192.168.1.
Note: To ensure proper screen refresh after a command entry, be sure that Internet Explorer 5.0 is configured as follows: Under the menu Tools/Internet Options/General/Temporary Internet Files/Settings, the setting for “Check for newer versions of stored pages” should be “Every visit to the page.” Setup Wizard Quickstart The first item in the Setup Wizard is Quickstart. The ADSL Wireless Base Station displays the Quickstart Web page.
• Telephone Service The telephone service is disabled by default. If you want to enable the Telephone function of the ADSL Wireless Base Station you can check the enable box to turn on the “Telephone Service” function. • Click the “Save Settings/Next” button. Once you leave your Telephone Service disabled please click on “Save Settings” and continue. You can now surf to your favorite websites by typing an URL in your browser’s location box or by selecting one of your favorite Internet bookmarks.
2. Phone Number Settings Enter the telephone number, Login and Password supplied by your Internet Service provider. Repeat this for each available port. The Belgacom b-box can append telephone numbers to outgoing calls. Select the number you want to use for each port. Click “Save Settings”. The connection status page will appear. 3. Click the “Ok” button. Congratulations! Your Telephone configuration is complete. Click “OK” to continue.
ADSL ADSL (Asymmetric Digital Subscriber Line) is designed to deliver more bandwidth downstream (from the central office to the customer site) than upstream. This section is used to configure the ADSL operation type and shows the ADSL status.
Status The Status screen displays information on connection line status, data rate, operation data and defect indication, and statistics.
The following items are included on the ADSL status page: 28
Advanced Setup Clicking the Home icon returns you to the home page. The Main Menu links are used to navigate to other menus that display configuration parameters and statistics. The Belgacom b-box’s advanced management interface contains 14 main menu items as described in the following table.
File Allows you to enable or disable file server functionality. Server Tools Contains options to back up and restore the current configuration, restore all configuration settings to the factory defaults, update system firmware, or reset the system. Status Provides WAN connection type and status, firmware and hardware version numbers, system IP settings, as well as DHCP, NAT, and firewall information.
Check “Enable Automatic Time Server Maintenance” to automatically maintain the Belgacom bbox’s system time by synchronizing with a public time server over the Internet. Then configure two different time servers by selecting the options in the Primary Server and Secondary Server fields. Password Settings Use this page to restrict access based on a password. By default, there is no password. For security you should assign one before exposing the Belgacom b-box to the Internet.
Note: If you check “Enabled” and specify an IP address of 0.0.0.0, any host can manage the Belgacom b-box. For remote management via WAN IP address you need to connect using port 8080. Simply enter WAN IP address followed by :8080 in the address field of your web browser, for example, 212.120.68.20:8080.
Domain Name Servers are used to map a domain name (e.g., www.somesite.com) to the equivalent numerical IP address (e.g., 64.147.25.20). Your ISP should provide the IP address of one or more Domain Name Servers. Enter those addresses on this page. WAN Specify the WAN connection parameters provided by your Internet Service Provider (ISP). The Belgacom b-box can be connected to your ISP in one of the following ways: ATM PVC Clone MAC ATM PVC The Belgacom b-box uses ATM as its WAN interface.
Protocol Protocol used for the connection. ATM Interface Clicking on the ATM VC brings up the following screen. The Belgacom b-box uses ATM as its WAN interface. Protocols including 1483 Routing, 1483 Bridging, MAC Encapsulated Routing (MER), PPPoA and PPPoE with LLC-SNAP and VC-Mux encapsulations are supported for each ATM PVC. When you have finished entering your connection parameters, click “SAVE SETINGS.
PPPoE: Point-to-Point over Ethernet is a common connection method used for xDSL. MAC Encapsulated Routing: If your ADSL service is a Bridged mode service and you want to share the connection to multiple PC’s, please select MAC Encapsulated Routing. MER is a protocol that allows you do IP routing with NAT enabled. VPI/VCI See Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI).
Some ISPs may require that you register your MAC address with them. If this is the case, the MAC address of the Belgacom b-box must be changed manually to the MAC address that you have registered with your ISP. LAN Use the LAN menu to configure the LAN IP address and to enable the DHCP server for dynamic client address allocation.
Parameter Description LAN IP IP Address The IP address of the Belgacom b-box. IP Subnet Mask The subnet mask of the Belgacom b-box. DHCP Server To dynamically assign an IP address to client PCs, enable the DHCP (Dynamic Host Configuration Protocol) Server. Lease Time Set the DHCP lease time.
End IP Domain Name Specify the start IP address of the DHCP pool. Do not include the gateway address of the Belgacom b-box in the client address pool. (See “TCP/IP Configuration” on page 3-2). If you attempt to include the Belgacom b-box gateway address (192.168.1.1 by default) in the DHCP pool, an error dialog box will appear. If you change the pool range, make sure the first three octets match the gateway’s IP address, i.e., 192.168.1.xxx. Specify the end IP address of the DHCP pool.
characters. Functioning as an access point, the Gateway can be configured for roaming clients by setting the SSID and wireless channel. See the description of the parameters below. Parameter Description SSID Service Set ID. The SSID must be the same on the Belgacom b-box and all of its wireless clients. Note: The SSID is case sensitive and can consist of up to 32 alphanumeric characters. (Default: WLAN) SSID Broadcast Enable or disable the broadcasting of the SSID.
Access Control Using the Access Control functionality, you can specify which PCs can wirelessly connect to the access point. Each PC has a unique identifier known as a Medium Access Control (MAC) address. With MAC filtering enabled, only the computers whose MAC address you have listed in the filtering table may connect to the Belgacom b-box. See the description of the Access Control features below. Parameter Description Enable MAC Enable or disable the MAC filtering function.
Filtering Access Rule for When MAC filtering is enabled, all registered MAC addresses registered MAC are controlled by the Access Rule. address MAC Filtering Lists allowed MAC addresses. Table (up to 32 stations) Security It is important to be aware of security issues, especially when using wireless. You can configure your security settings on this page. If you are transmitting sensitive data across radio channels, you should enable wireless security.
network and management resources available, and the software support provided on wireless clients. A summary of wireless security considerations is listed in the following table. Security WEP WPA 802.1X Client Support Built-in support on all 802.11b and 802.
See the description of the Access Control features below. Parameter Description WEP WEP Mode Key Entry Method You can choose disabled, 64-bit or 128-bit encryption. When MAC filtering is enabled, all registered MAC addresses are controlled by the Access Rule. Key Provisioning Select static key or dynamic key. Static WEP Key You may manually enter the keys or automatically generate Setting encryption keys.
With TKIP, WPA uses 48-bit initialization vectors, calculates an 8-byte message integrity code, and generates an encryption key periodically. For authentication, it allows you to use 802.1x authentication for an environment with a RADIUS server installed on your network. Selecting the Pre-shared Key enables WPA to use the pre-shared key in a SOHO network. See the description of the WPA settings below. Field Default Parameter Description WPA mode The security mode your product is currently using.
802.1X Management access will be checked against the authentication database stored on the router. If an authentication RADIUS server is used, you must specify the secret key of the Message-Authenticator attribute, i.e., Message Digest-5 (MD5), and the corresponding parameters in the RADIUS Server Parameters field for the remote authentication protocol. See the description of the 802.1x features below. • General Parameters Field Default Parameter Description Enable 802.
Server Port 1812 UDP port used for RADIUS authentication messages. Re-Authentication 3600 Defines a maximum period of time for which the Period seconds Secret Key None NAS-ID None RADIUS server will dynamically reassign a session key to a connected client station. Defines a text string on both the RADIUS client and server to secure RADIUS traffic.The RADIUS server requires the MD5 MessageAuthenticator attribute for all access request messages. The 802.
NAT Settings NAT allows one or more public IP addresses to be shared by multiple internal users. Enter the Public IP address you wish to share into the Global IP field. Enter a range of internal IPs that will share the global IP.
Address Mapping Use Address Mapping to allow a limited number of public IP addresses to be translated into multiple private IP addresses for use on the internal LAN network. This also hides the internal network for increased privacy and security.
Virtual Server Using this feature, you can put PCs with public IPs and PCs with private IPs in the same LAN area. If you configure the Belgacom b-box as a virtual server, remote users accessing services such as web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses.
Special Applications Some applications, such as Internet gaming, videoconferencing, Internet telephony and others, require multiple connections. These applications cannot work with Network Address Translation (NAT) enabled. If you need to run applications that require multiple connections, use the following screen to specify the additional public ports to be opened for each application. Specify the public port number normally associated with an application in the Trigger Port field.
Note: Choosing a row that already contains data will overwrite the current settings. Example: ID 1 2 Trigger Port Trigger Type Public Port 6112 UDP 6112 230028800 TCP 2400, 47624 Public Type UDP TCP Comment Battle.net MSN Game Zone For a full list of ports and the services that run on them, see www.iana.org/assignments/portnumbers.
NAT Mapping Table NAT Mapping Table displays the current NAPT address mappings. The NAT address mappings are listed 20 lines per page, click the control buttons to move forwards and backwards. As the NAT mapping is dynamic, a Refresh button is provided to refresh the NAT Mapping Table with the most up-to-date values. The content of the NAT Mapping Table is described as follows: Protocol - protocol of the flow. Local IP - local (LAN) host’s IP address for the flow.
Gateway Enter the WAN IP address of the gateway to the remote network. Configure Allows you to modify or delete configuration settings. Click Add to display the following page and add a new static route to the list. Parameter Description Index Displays the number of the route. Network Address Enter the IP address of the remote computer for which to set a static route. Subnet Mask Enter the subnet mask of the remote network for which to set a static route.
Parameter Description General RIP Parameters RIP mode Globally enables or disables RIP. Auto summary If Auto summary is disabled, then RIP packets will include sub-network information from all subnetworks connected to the ADLS Router. If enabled, this sub-network information will be summarized to one piece of information covering all sub-networks. Table of current Interface RIP parameter Interface Operation Mode The WAN interface to be configured. Disable: RIP disabled on this interface.
not participate in sending route broadcasts. Parameter Description Version Sets the RIP version to use on this interface. Poison Reverse A method for preventing loops that would cause endless retransmission of data traffic. Authentication Required None: No authentication. Password: A password authentication key is included in the packet. If this does not match what is expected, the packet will be discarded.
R = RIP (Routing Information Protocol) assigned route. I = ICMP (Internet Control Message Protocol) Redirect route. Network Destination IP address. Address Netmask The subnetwork associated with the destination. This is a template that identifies the address bits in the destination address used for routing to specific subnets. Each bit that corresponds to a “1” is part of the subnet mask number; each bit that corresponds to “0” is part of the host number.
Access Control Access Control allows users to define the outgoing traffic permitted or not-permitted through the WAN interface. In the example above, all incoming and outgoing emails are blocked. The default is to permit all outgoing traffic. (See the following page for details.) The Belgacom b-box can also limit the access of hosts within the local area network (LAN). The MAC Filtering Table allows the Belgacom b-box to enter up to 32 MAC addresses that are not allowed access to the WAN port.
Define the appropriate settings for client PC services (as shown above). Click “OK” to save your settings. The added PC will now appear in the Access Control page. MAC Filter Use this page to block access to your network using MAC addresses.
The Belgacom b-box can also limit the access of hosts within the local area network (LAN). The MAC Filtering Table allows the Belgacom b-box to enter up to 32 MAC addresses that are allowed access to the WAN port. All other devices will be denied access. URL Blocking To configure the URL Blocking feature, use the table below to specify the web sites (www.somesite.com) and/or keywords you want to filter on your network.
The Belgacom b-box allows the user to block access to web sites from a particular PC by entering either a full URL address or just a keyword. This feature can be used to protect children from accessing violent or pornographic web sites.
Schedule Rule You may filter Internet access for local clients based on rules. Each access control rule may be activated at a scheduled time. Define the schedule on the Schedule Rule page, and apply the rule on the Access Control page. Click Add Schedule Rule. Edit Schedule Rule You can create and edit schedule rules on this page.
Define the appropriate settings for a schedule rule (as shown on the following screen). The rule in the screen shot above prohibits emailing from 3.00pm to 11.59pm from Monday to Thursday. Upon completion, click “OK” to save your schedule rules.
Network attacks that deny access to a network device are called DoS attacks. DoS attacks are aimed at devices and networks with a connection to the Internet. Their goal is not to steal information, but to disable a device or network so users no longer have access to network resources.
the stated destination computer has previously requested the current communication. This is a way of ensuring that all communications are initiated by the recipient computer and are taking place only with sources that are known and trusted from previous interactions. In addition to being more rigorous in their inspection of packets, stateful inspection firewalls also close off ports until a connection to the specific port is requested.
POP3 Server Address User Name Password Enter your POP3 server address (usually the part of the email address following the “@” sign). Enter your email account user name. Enter your email account password. Connection Policy Fragmentation 10 secs Configures the number of seconds that a packet half-open wait state structure remains active. When the timeout value expires, the router drops the unassembled packet, freeing that structure for use by another packet.
sensitive time period Maximum 30 Maximum number of half-open fragmentation half-open packets from the same host. fragmentation packet number from same host Half-open 1 secs Length of time before a half-open fragmentation fragmentation session is detected as half-open. detect sensitive time period Flooding cracker 300 secs Length of time from detecting a flood attack to block time blocking the attack.
SNMP Community Use the SNMP configuration screen to display and modify parameters for the Simple Network Management Protocol (SNMP). A computer attached to the network, called a Network Management Station (NMS), can be used to access this information. Access rights to the agent are controlled by community strings. To communicate with the Belgacom b-box, the NMS must first submit a valid community string for authentication.
Trap Parameter Description IP Address Community Version Traps are sent to this address when errors or specific events occur on the network. A community string (password) specified for trap management. Enter a word, something other than public or private, to prevent unauthorized individuals from reading information on your system. Sets the trap status to disabled, or enabled with V1 or V2c. The v2c protocol was proposed in late 1995 and includes enhancements to v1 that are universally accepted.
ADSL ADSL Parameters We recommend leaving the Operation Mode at the default Automatic setting, to automatically negotiate with the remote DSLAM. Parameter Description Operation Mode • Automatic T1.413 Issue 2 G.992.1 (G.DMT) G.992.2 (G.Lite) G.992.3 (ADSL2) G.992.5 (ADSL2+) Status The Status page displays ADSL status information.
Parameter Description Status Line Status Data Rate Upstream Downstream Operation Data/Defect Indication Noise Margin Upstream: Downstream: Output Power Attenuation Upstream: Downstream: Fast Path FEC Correction Interleaved Path FEC Correction Fast Path CRC Error Interleaved Path CRC Error Loss of Signal Defect 70
Loss of Frame Defect Shows the current status of the ADSL line. Actual and maximum upstream data rate. Actual and maximum downstream data rate. Minimum noise margin upstream. Minimum noise margin downstream. Maximum fluctuation in the output power. Maximum reduction in the strength of the upstream signal. Maximum reduction in the strength of the downstream signal. There are two latency paths that may be used: fast and interleaved.
Fast Path Header Error Concealment errors. Interleaved Path Header Error Concealment errors. (Superframes represent the highest level of data presentation. Each superframe contains regular ADSL frames, one of which is used to provide superframe synchronization, identifying the start of a superframe. Some of the remaining frames are also used for special functions.) Number of interleaved superframes received. Number of interleaved superframes transmitted. Number of fast superframes received.
See the table below for a description of the parameters. Parameter Description Phone 1/2 Enable Enable/disable phone 1 and/or 2. Phone Number Your phone number. Display Name Your name, often the same as your phone number. SIP Domain (From your Telephony provider, e.g., “sipcenter.com” or an IP address.) Realm (From your Telephony provider.) Username (From your Telephony provider.) Password (From your Telephony provider.
SIP, the Session Initiation Protocol, is a signaling protocol for Internet conferencing, telephony, presence, events notification and instant messaging. The call waiting feature allows the user to take an incoming call, even though the user is already on the phone. The user upon hearing the new call, can put the original caller on hold and speak to the new caller. When the user hasn’t finished talking to the new caller, he can resume his conversation with the original caller.
Registrar Setting Set the registrar settings. Registrar IP: IP address of SIP registrar. Registrar Port: Port number of SIP registrar. Telephony Advanced Setting Configure the Telephony advanced settings on this page, and click “OK.” SIP is a peer-to-peer protocol. The peers in a session are called User Agents (UAs). A user agent can function in one of the following roles: 1. User agent client (UAC) - A client application that initiates the SIP request. 2.
1. 2. 3. 4. G.711 A law G.711 U law G.729 G.723.3 See the table below for a description of the parameters. Parameter Description Support Call Enables or disables support for call waiting. Waiting (Default: Disabled) Support User-Agent Enables or disables user-agent header support. Enabling this Header feature includes user agent information in the packet, e.g., the caller’s ID may be displayed.
Telephony Status View the Telephony status for both FXS ports on this page. Click “Refresh” to update this page. This page displays the Port Type, SIP URL and Registration status of the Belgacom b-box. See the table below for a description of the parameters. Parameter Port Type SIP URL Registration Description Displays the port type, i.e., FXS. Shows the SIP URL. Indicates whether the user has successfully registered or not. Telephony Call Logs View the call log for both FXS ports on this page.
Dialed Call Rejected Call Forwarded Call Number of calls made. Number of rejected calls. Number of forwarded calls. Maintenance Check Backup Router Configuration and click “NEXT” to save your Belgacom b-box’s configuration to a file named “backup.bin” on your PC. You can then check Restore from saved Configuration file (backup.bin) to restore the saved backup configuration file. To restore the factory settings, check Restore router to Factory Defaults and click “NEXT.
Download the file to your hard drive. Then click Browse... to find the file on your computer. Select the firmware file and click “Open.” Click “SAVE” to start the upgrade process. Reset Perform a reset from this page. Should your unit become unresponsive for any reason, you can simply perform a reset from this page. Performing a reset will reboot the device. Your configuration settings will remain the same.
Status The Status screen displays WAN/LAN connection status, firmware and hardware version numbers, as well as information on DHCP clients connected to your network.
The security log may be saved to a file by clicking “SAVE” and choosing a location. The following items are included on the Status screen: Parameter Description INTERNET Release Renew GATEWAY INFORMATION ATM PVC Security Log Save Clear Refresh DHCP Client Log Displays WAN connection type and status. Click on this button to disconnect from the WAN. Click on this button to establish a connection to the WAN. Displays system IP settings, as well as DHCP Server and Firewall status.
APPENDIX A TROUBLESHOOTING This section describes common problems you may encounter and possible solutions to them. The Belgacom b-box can be easily monitored through panel indicators to identify problems. Troubleshooting Chart Symptom Action LED Indicators POWER LED is Off • Check connections between the Belgacom b-box, the external power supply, and the wall outlet.
Troubleshooting Chart Symptom Action Management Problems Cannot connect using the Web browser Forgot or lost the password • Be sure to have configured the Belgacom b-box with a valid IP address, subnet mask, and default gateway. • Check that you have a valid network connection to the Belgacom b-box and that the port you are using has not been disabled. • Check the network cabling between the management station and the Belgacom b-box.
GLOSSARY 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 UTP cable. Auto-Negotiation Signalling method allowing each node to select its optimum operational mode (e.g., 10 Mbps or 100 Mbps and half or full duplex) based on the capabilities of the node to which it is connected.
A 100 Mbps network communication system based on Ethernet and the CSMA/CD access method. Full Duplex Transmission method that allows two network devices to transmit and receive concurrently, effectively doubling the bandwidth of that link. IEEE Institute of Electrical and Electronic Engineers. IEEE 802.3 Defines carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications. IEEE 802.
transmission medium, facilitating the exchange of data between network nodes. MIB An acronym for Management Information Base. It is a set of database objects that contains information about the device. RJ-45 Connector A connector for twisted-pair wiring. Straight-through Port An RJ-45 port which does not cross the receive and transmit signals internally (MDI) so it can be connected with straight-through twisted-pair cable to any device having a crossover port (MDI-X).
SPECIFICATIONS Standards Compliance CE Mark Emissions FCC Class B, VCCI Class B Industry Canada Class B EN55022 (CISPR 22) Class B C-Tick - AS/NZS 3548 (1995) Class B Immunity EN 61000-3-2/3 EN 61000-4-2/3/4/5/6/8/11 Safety UL 1950 EN60950 (TÜV) CSA 22.2 No. 950 IEEE 802.3 10 BASE-T Ethernet IEEE 802.3u 100 BASE-TX Fast Ethernet Modem Standards ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.handshake) ITU T.
Storage -40 to 70 °C (-40 to 158 °F) Humidity 5% to 95% (non-condensing) 90
Information Hereby, Philips Consumer Electronics, BLC P&ACC, declares that this CIA6726N/BG is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Hierbij verklaart, Philips Consumer Electronics, BLC P&ACC dat het toestel CIA6726N/BG in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
