Condenser Time Dryer DC 7110
Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference. This User Manual will • Help you use your machine in a fast and safe way. • Read the User Manual before installing and starting your product.
TABLE OF CONTENTS 1 Your Dryer 4 Overview..............................................4 Technical Specifications........................5 2 Important safety information 6 General safety......................................6 Intended use........................................7 Children’s safety...................................7 3 Installation 8 Appropriate installation location............8 Removing the transportation safety assembly..............................................
1 Your Dryer Overview 7 1 6 5 2 4 3 1- Control panel 5- Rating plate 2- Kick plate opening tab 6- Fluff filter 3-Adjustable feet 7- Power cord 4-Kick plate 4 EN
Technical Specification EN 2 Height (adjustable) 84.6 cm Width 59.5 cm Depth 53 cm Capacity (max.) 7 kg Weight (net) 35 kg Voltage Check the rating label Rated power input Model code Rating label is located behind the loading door. Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.
2 Important safety information This section includes safety information that will help protection from risks of personal injuries or materialistic damages. Failure to follow these instructions shall cause any warranty and reliability commitment to become void. General safety • Never place the machine on a carpet-covered floor, otherwise, lack of airflow beneath the machine may cause electrical parts to overheat. This will cause problems with your machine.
• • • • • • • • • • There is the risk of electric shock! Always disconnect by unplugging from the mains before cleaning. Never touch the plug with wet hands. Never unplug by pulling on the cable, always pull out by grabbing the plug only. Do not operate the machine if the power cable or plug is damaged! Never attempt to repair the machine yourself, otherwise, you will be putting your life and others’ lives in danger.
3 Installation A Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks for your safety. Appropriate installation location • Install the product in an environment which has no risk of freezing and is in a stable and level position. • Operate your product in a well ventilated, dust-free environment. • Do not block the air ducts in front of and under the product with materials such as long pile rugs and wooden plinths.
Disposing of packaging material Packaging materials are dangerous to children. Keep packaging materials in a safe place out of reach of children. Packaging materials of your product are manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste. Transportation of the machine 1. Unplug the machine from the mains. 2. Remove the water drain and vent connections (if any). 3.
4 Electrical Connection Make sure that you have an earthed power outlet socket rated at 13 amps (minimum). Attention! When installed, the socket must be reachable after installation, or a separate switch (which can disconnect the two poles) must be used in the installation. Check for suitability. For a permanent connection, a master switch with at least 3mm contact clearance and minumum 13 A rating must be used. Electrical requirements with the symbol or coloured green and yellow or green.
5 Initial preparations for drying Things to be done for energy saving: • Make sure that you operate the product at its full capacity but pay attention to not exceeding it. • Spin your laundry at the highest speed possible when washing them. Thus, the drying time is shortened and energy consumption is decreased. • Pay attention to dry same types of laundry together. • Follow the instructions in the user manual for programme selection.
• Garments or pillows bolstered with rubber foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads should not be dried in the dryer. • Do not use fabric softeners and anti-static products unless they are recommended by the manufacturers of the fabric softener or the product. • Do not dry the underwear reinforced with metal parts in the dryer. If these metal reinforcements loosen and break during drying, they will damage your dryer.
6 Selecting a Programme and Operating Your Machine Control panel 1 7 2 4 3 6 5 1. Filter cleaning warning light Warning light turns on when the filter is full. 2. Programme follow-up indicator Used to follow-up the progress of the current programme. 3. Low temperature Used to dry in low temperatures. 4. On/Off button Used to turn on and off the machine. 5. Programme selection knob Used to select a programme. 6. Start/Pause/Cancel button Used to start, pause or cancel the programme. 7.
Preparing the machine 1. Plug in your machine. 2. Place the laundry in the machine. 3. Press the “On/Off” button. C Pressing the “On/Off” button does not necessarily mean that the programme has started. Press “Start/Pause/Cancel” button of the machine to start the programme. Timer programme selection Decide the appropriate time from the table below which includes drying temperature in degrees. Select the desired time with the timer programme selection button.
Programme selection and consumption table EN Programme table Approximate Programmes Capacity (kg) Spin speed in washing amount of Drying time machine (rpm) remaining (minutes) humidity Cottons / Coloreds 7 A Cupboard dry 3.5 7 A Iron dry 3.5 1000 60 % 135 800 70 % 150 1000 60 % 90 800 70 % 105 1000 60 % 105 120 800 70 % 1000 60 % 60 800 70 % 60-90 800 40 % 60 600 50 % 90 Synthetics B Cupboard dry 3.
Auxiliary function Low temperature This function allows for drying at lower temperatures and therefore saves energy. Warning LED will light up when you select the function. C You must use this function when you dry your synthetic or delicate laundry. Adding/removing laundry in standby mode In order to add or take out laundry after the start-up of the programme; 1. Press the “Start/Pause/Cancel” button to switch the machine to “Pause” mode. Drying process will stop. Warning indicators 2.
and “Water tank” warning LEDs as well as the “0” warning LED on the programme follow-up indicator will light up at the end of this period for reminding purposes. A As the inside of the machine will be excessively hot when you cancel the programme while the machine is running, activate the ventilation programme to cool it down. The machine will not start even if the “Start/ Pause/Cancel” button is pressed, unless the programme selection knob is returned to the initial programme.
7 Maintenance and cleaning Filter Cartridge / Door Inner Surface Lint and fibres released from the laundry to the air during the drying cycle are collected in the “Filter Cartridge”. *To drain the water tank: 1-Carefully remove the water tank by opening the kick plate cover/pulling the drawer. 2-Drain the water in the tank C Such fibre and lint are generally formed during wearing and washing. C Always clean the filter and the inner surfaces of the cover after each drying process.
For the condenser; Hot and humid air in the condenser is cooled with the cold air from the room. Thus, the humid air circulating in your dryer is condensed and then pumped into the tank. C Clean the condenser after every 30 drying cycles or once a month. To clean the condenser: 1. If a drying process has been carried out, open the door of the machine and wait until it cools down. 4. Clean the condenser by applying pressurized water with a shower armature and wait until the water drains. 5.
8 Suggested solutions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water Laundry comes out wet at the end of drying. • Meshes of the filter may be clogged. Wash with water. • Excessive laundry might have been loaded in. Do not load the dryer in excess. Dryer does not switch on or the programme does not start. Dryer is not activated when set. • It might have not been plugged in. Make sure that the machine is plugged in. • The loading door may be ajar.
9 Guarantee Your new product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase. Important notes What is covered? • Repairs necessary as a result of faulty materials, defective components or manufacturing defect. • The cost of functional replacement parts, but excluding consumable items. • The labour costs of a approved repairer to carry out the repair. What is not covered? • Transit, delivery or accidental damage or misuse and abuse.
10 Service Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it should the product require attention under guarantee. You should also complete the details below; it will help us assist you when requesting service.