CCB 7140 XA Hood User Manual
Please read this user manual first! Dear Customer, Thank you for prefering a Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use. If you handover the product to someone else, give the user manual as well.
TABLE OF CONTENTS 1 Recommendations and Suggestions 4 1.1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Characteristics 6 2.1 Components . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.3 Technical Specifications . . . . . . . . . . . . . . . . 6 3 Installation 7 3.
1 Recommendations and Suggestions A The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. 1.1 Installation • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
1 Recommendations and Suggestions 1.3 Maintenance • The exhaust air must not be discharged into a flue which is used for exhausting fumes from other appliances burning gas or other fuels. (Not applicable for appliances which only discharge air back into the room) • The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood: When the range hood is located above a gas appliance, this distance shall be 65cm.
2 Characteristics 2.1 Components Ref. Q.ty Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filters 8 1 Directional Air Outlet grille 9 1 Reducer Flange ø 150-120 mm Ref. Q.ty Installation Components 12e 2 Screws 2,9 x 9,5 Q.ty Documentation 1 Instruction Manual 2.2 Dimensions 2.
3 Installation 3.1 Drilling the Support surface and Fitting the Hood Hood Type L1 52 497 70 677 Make a rectangular opening on the base of the hanging unit, leaving a minimum of 13 mm from the outer edges. Snap-On Fitting For hoods with snap-on side supports only, set up for a support panel thickness of between 15 mmand 30 mm. • Insert the hood until the side supports snap into place. • Lock in position by tightening the screws Vf from underneath the hood.
3 Installation 3.2.2 Recirculation Version Air Outlet • Cut a hole ø 125 mm in the wall unit over the hood. • Insert the reducer flange 9 on the hood body outlet. • Connect the hood body outlet to the top part of the wall unit using a rigid or flexible pipe ø120 mm, to be selected by the installer. • Fix the pipe in position using sufficient pipe clamps (not supplied). • Fix the directional grille 8 on the recirculation air outlet using the 2 screws 12e (2,9 x 9,5) provided.
4 Use 4.1 Control panel L Light Switches the lighting system on and off M Motor Switches the extractor motor on and off V Speed Sets the operating speed of the extractor: 1. Low speed, used for a continuous and silent air change in the presence of light cooking vapour. 2. Medium speed, suitable for most operating conditions given the optimum treated air flow/noise level ratio. 3.
5 Maintenance 5.1 Grease Filters 5.1.1Cleaning Metal Self- Supporting Grease Filters • Replace the filters on the grill, fix them in position using the filter retaining clips and close the filter retaining grill. • The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. • Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time.
5 Maintenance 5.2 Odour filters (Recirculation version) 5.3 Lighting 5.2.1 Replacing Activated Charcoal Filters 5.3.1 Light Replacement • These filters are not washable and cannot be regenerated, and must be replaced approximately every four months of operation, or more frequently with heavy usage. • Remove the grease filters. • Remove the saturated activated carbon filters by releasing the fixing hooks. • Fit the new filters by hooking them into their seating • Replace the grease filters.
Beko Manufacturers Guarantee Congratulations on purchasing a quality Beko product. Beko automatically provide you with a 2 year Manufacturers Guarantee, covering parts and labour for servicing within the geographical limits of Australia and New Zealand. General Terms and Conditions For Australian Consumers goods come with guarantees that cannot be excluded under the Australian Consumer Law.
Terms and Conditions Beko Australia and New Zealand Pty Ltd guarantees to the original purchaser to repair, or at its option replace, without charge to the owner for any part which is not of ‘acceptable quality’ within two years of date of purchase. “No Lemon Guarantee” * if the product fails more than 2 times during the Guarantee period due to the same type failure caused by the same part, we will automatically replace the product with an equivalent product free of charge.
2. This Guarantee does not cover damage caused by: a. Misuse or abuse of the Beko Product b. Accidental damage of any kind c. Rust and Corrosion where the product is located within a corrosive environment d. Discolouration of burners or trivets on gas cooktops or chrome surrounds e. Incorrect operation or not following the operation instructions as stated in the user manual. f. Improper installation g. Failure to clean or improper cleaning h.
This Guarantee has been designed for Products used in normal domestic environment. Our products are not designed for commercial use. Any commercial use may affect this Product’s Guarantee. Service under this Manufacturer’s Guarantee is provided by the Beko Australia and New Zealand Authorised Repairer. The Guarantee is provided by Beko Australia and New Zealand Pty Ltd (ABN: 49 152 055 162) of 55 Blanck Street, Ormeau, QLD Australia 4208, P O Box 354 Ormeau QLD Australia 4208.
