Dect Phone User Manual BD-300
Contents What the symbols mean ...................................................................3 The Handset and Base Unit..............................................................4 Setting up your telephone.................................................................5 Installation ........................................................................................6 Important safety information ..........................................................7 Phone Book ...........................
What the symbols mean Batteries charge level Whenever this shows ‘nearly empty’ ( ), put the handset on the base unit to charge the batteries. While the batteries are being charged, the level shown will keep changing. Outside call You are connected to an outside call. Intercom call You are connected to an intercom call. Phone book Show the names and numbers of stored record. Mute Your handset's microphone is muted. Up and down arrows To browse through the programming menu for more options.
The Handset and Base Unit MENU/ Mute button PHONEBOOK/OK/Recall button Press to enter menu mode and enter sub-menu. Use the key " " to lock or unlock the keypad. Press during a call to mute the microphone Speakerphone button In standby mode, press to enter phonebook mode. Press to confirm selection. You can activate Recall function if your phone is connected to a PABX, or if you use Select Services. Press to transfer an outside call to another phone.
Setting up your telephone Connection and conditions for use You can connect your phone to a direct exchange line (DEL), a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect your phone as an extension to a payphone. How many phones can you connect? The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.
Installation 1. Choose a suitable site for the handset unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead into the power jack on the base unit and plug the telephone line cord into the telephone port. 3. Plug the mains adapter into a 230V AC, 50 Hz mains socket, with the switch on the socket set to OFF Note: The illustration of adaptor may vary from country to country. 4. Switch on mains power at the socket 5.
Important safety information This equipment is not designed for making emergency calls in the event of a power failure. Alternative arrangements should be made for access to emergency services. (This means that you should also have a basic phone that does not need mains power, connected to your line so that you can make calls during a power failure) People with a heart pacemaker should consult their doctor before using the telephone.
Making and answering calls To switch the handset ON or OFF Press and hold the CLEAR button for 2~3 seconds to switch the handset ON /OFF. To make a call 1. Key in the telephone number (If you make a mistake, press CLEAR button to clear digits from the display. To clear all digits, press and hold CLEAR button.) 2. Press the CALL button. 3. Or you also can dial the stored number through UP/DOWN button.
To store new number into phonebook 1. Press the OK button, the display shows ADD 2. Press the OK button again, then key in the name and the number 3. Press the OK button to confirm 4. Press the CLEAR button twice to return to standby mode, or you can continue to store number. To clear a number from phonebook 1. Press the OK button, the display shows ADD 2. Press UP/DOWN button to the location DELETE 3. Press OK button to confirm, then press UP/DOWN button to select the number you want to delete 4.
2. Press the OK button, then press UP/DOWN button to the locations MISSED, RECEIVED, or DIALED calls. 3. Press the OK button, then press UP/DOWN button to scroll the records To save a number in call logs When you received a new number, you want to store in phonebook. The following is for your reference. 1. 2. 3. 4. Repeat step 1 to 3 above, until the display shows the new number.
Ringer Volume (EXT / INT) You can adjust the ringer volume following the below instruction. 1. Press the MENU button, then press UP/DOWN button to the location HANDSET 2. Press the OK button, then press UP/DOWN button to the location EXT VOL / INT VOL 3. Press the OK button The display shows the current volume level 4. Press UP/DOWN button to change the volume 5.
! If you have turned auto-talk on, do not press the CALL button after you have answered a call by lifting the handset, otherwise, you'll disconnect the call. To Lock /Unlock the keypad Press MENU button and “ “ button consecutively to lock or unlock the keypad. Base Setting Note: The default PIN is: 0000 Call Barring Function (Optional) Call barring enables you to restrict or bar certain types of calls from your phone. To set call barring number 1.
4. Press UP/DOWN button to change the volume 5. Press the OK button to confirm the volume level you chosen Least cost route (LCR) function (Optional) With the LCR function, the phone will automatically replace a long number (up to 11 digits) with a comparative short number (up to 3 digits), to simplify the process of dialing a long number. Example: If you program to replace "00" with "17909", whenever you dial a number beginning with the“00”, the phone will automatically change this to “17909”.
2. Press the OK button, the display shows PIN? 3. Key in your PIN number and press the OK button, then UP/DOWN button to the location MAST PIN? 4. Press OK button, the display shows PIN?, Key in the original PIN number(default PIN:0000) 5. Repeat the step 4 and the display shows MAST PIN 6. Press OK button, the display shows PIN?, Key in the new PIN number, 7.
1. Disconnect the power lead from the back of the base unit 2. Press and hold the HANDSET LOCATOR button in the base unit, at the same time connect the power lead into the back of base unit. Release the LOCATOR button after you hear “beep” sound for five times. The IN USE light on base unit lights during this whole process. 3. After 2~3 seconds, you can hear “beep” sound for two times again and the IN USE light goes off; 4.
Intercom and transfer To make an intercom call 1. Press the INT button 2. Key in the number of the other handset On the other handset's display, your number appears, and the INT symbol flashes. Then the other handset user presses the CALL button to connect the call. For details of how to change the ringing melody and volume for intercom calls, see "INT MELODY" and "INT VOLUME" on "HANDSET SETTING" part.
Check the batteries level symbol on the display. If it is low, replace the handset on the base unit or charger pod to recharge the batteries. Switch off power at the mains socket, wait for a few seconds and then switch back on. This may solve the problem. If you still can’t make calls, try re-registering the handset. When I press keys on the handset, nothing happens. Make sure the batteries are fitted in your handset. If the batteries level symbol on the display shows “low”, recharge the batteries.
You need to subscribe to the Caller Display feature from your service provider. The caller may have withheld their number, or they may be calling from a network that does not transmit the Caller ID (for example, it may be an international call). The handset’s battery is running low within an hour or two. Before you used the handset for the first time, you should have left it on the base unit for up to 15 hours to charge the batteries fully. You may need to replace the batteries. I cannot transfer a call.