Instruction Manual
4. CONFIGURATION
Rate Totalisers are supplied configured as requested at time of ordering, if not specified default configuration will be supplied but can easily be changed on-site.
Fig 6 shows the location of each function within the configuration menu with a brief summary of the function. Please refer to the full instruction manual for detailed configuration information and for description of lineariser and optional outputs.
Access to the configuration menu is obtained by pressing the ( and ) buttons simultaneously. If the Rate Totaliser's security code is set to default 0000 the first parameter function will be displayed. If the instrument is protected by a security code, code will be displayed. The four digit
code must be entered to gain access to the menu.
Fig 6 Configuration menu
Manuals, certificates and data-
sheets can be downloaded from
http://www.beka.co.uk/ba337_8e
Unless otherwise specified menu functions are shown on the upper display
Security Code
Enter code by
pressing
& or * & (
to move to next
digit. Code 0000
allows direct
access to
the menu
Function
& or *
to select
Function of
rate totaliser
5td
Linear
lin
16 segment
lineariser
&&
*
(
(
)
)
(
(
)
)
function
code
0000
)
*
(
)
)
)
( )
input
op.
col
Debounce
& or *
to select
level of
debounce.
default
heavy
light
&
)
debounce
( )
default
( )
update
0
.
5
inp.
type
&
*
&
*
DISPLAY
Display
mode
Input
& or *
to select
Input type
op.
col
Open
Collector.
volt5 l
Pulse
<1V >3V
volt5 h
Pulse
<3V >10V
coil
Magnetic
pick-off.
pr.
det
Proximity
detector.
contact
Switch
contact.
5td
Update
& or *
to select
interval
between
display
updates,
may be set to
0.5, 1, 2, 3, 4
or 5 seconds
)
( )
di5p-1
total
&
*
Upper Display
& or *
to select
whether
rate or total
is shown
on the upper
display
)
( )
di5p-2
on
&
*
Lower Display
& or *
to turn
lower display
on or off
)
( )
00000000
&
*
Decimal point
& or *
to select
position of
decimal
point and
( to toggle
between rate
and total
displays
)
( )
factor
001
.
00
&
*
K-factor
& or *
to select
value and
( to move
to next digit or
decimal point
Note: When
lin is
selected 16
values for
factor may
be entered
)
( )
5cale-t
&
Total scale
factor
Divides
factor
to produce
total display
Press
& or *
to adjust
value and
( to move
to next digit or
decimal point
dp
001
.
00
&
*
Clip off
Rate display
below which
totalisation
is inhibited
Press
& or *
to adjust value
of each digit
and
( to
move to next
digit
)
( )
*
clp off
000
.
0
&
*
Filter
& or *
to adjust
value of each
digit and
( to transfer
control to
other digit
First digit:
filter magnitude
second digit:
step response
Note: While
making
adjustments
the filtered
rate display is
shown on
lower display
so stability can
be assessed
)
( )
filter
&
*
&
*
Timebase
& or *
to select
rate display
timebase
tb-01
for flow/sec
tb-60
for flow/min
tb-3600
for flow/hour
)
( )
t-ba5e
tb-01
Rate scale
factor
Divides
factor
to produce
rate display
Press
& or *
to adjust
value and
( to move
to next digit or
decimal point
)
( )
5cale-r
001
.
00
*
(
)
)
)
( )
loc clr
&
)
clr gtot
( )
( )
clrgtot
clr tot
&
*
&
*
Local total
reset
& or *
to turn the
local total
reset function
on or off.
When on,
total display
is reset to
zero when
& and *
are operated
simultaneously
in display
mode for more
than 3 seconds
Local grand
total reset
& or *
to turn the
local grand total
reset function
on or off.
When on,
grand total
display may be
reset to
zero when
) and *
are operated
simultaneously
in display mode
for more than
10 seconds
Clear grand
total
Press
& or *
to select ye5
to reset grand
total to zero
Confirm
instruction by
entering 5ure.
Press
& or *
to adjust each
digit and
(
to move to
next digit
)
( )
&
*
When fitted optional alarms,
pulse output and 4/20mA
output functions appear here.
)
*
Reset
configuration
to factory
defaults
Confirm
instruction by
entering 5ure.
Press
& or *
to adjust each
digit and
(
to move to
next digit
24
off off
(
0000
clr.
no
Define
Security Code
Enter by
pressing
& or *
and ( to
move to next
digit
code
0000
)
(
0000
r5et def
The BA337E and BA338E are CE marked to show compliance with the European Explosive Atmospheres Directive 2014/34/EU and the European EMC Directive 2014/30/EU.
They are also UKCA marked to show compliance with UK statutory requirements Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations
UKSI 2016:1107 (as amended) and with the Electromagnetic Compatibility Regulations
UKSI 2016:1091 (as amended).
Fig 6 Conīæguration menu