Robot vacuum cleaner M6S User Manual Thank you for purchasing this product. Please read the user guide carefully before use.
Thank you for purchasing the M6S Robot vacuum cleaner. I hope you will enjoy it! If you have any questions about the product during use, please call our service hotline. Hotline: 4006-788-228 Table of Contents 1. Safety Instructions…………………………2-4 1.1 1.2 1.3 1.4 1.5 1.6 5. Product Maintenance…………………… 11-14 5.1 5.2 5.3 5.4 5.5 5.
1. Safety Instructions 1.1 Instructions for use Please pay attention to the following basic safety precautions before using the product: * Read the user manual carefully and follow the instructions in the user annual when using the product. * Keep the user manual well for future reference. * If you need to transfer the product to a third party, please attach the user manual along with the product.
Caution This product can only be used indoors. Prevent the suction of water, oil or other liquids, which may damage the vacuum cleaner. Arrange scattered wires on the floor before use for fear of affecting the normal operation of the vacuum cleaner. Remove fragile objects before use. When the product is working, removal of the charging dock will affect the normal recharging of the machine. Do not use this product to suck in sharp objects (e.g.
- non-rechargeable batteries are not to be recharged; different types of batteries or new and used batteries are not to be mixed; batteries are to be inserted with the correct polarity; exhausted batteries are to be removed from the appliance and safely disposed of; if the appliance is to be stored unused for a long period, the batteries should be removed; the supply terminals are not to be short -circuited. 1.
2. Product Composition 2.
2.
3. Product Installation Charging dock installation High voltage! Please dry your hands before operation for fear of electrical shock! Power adapter jack Charging terminal 1. Place the charging dock on a flat surface that is perpendicular to the wall. There shall be no obstacles within 3 meters in front and 1 meter on the left and right. Press firmly on the charging dock to attach it to the floor more firmly.
4. Product Use 4.1 4.1.1 Use of the host machine Diagrams of control keys Control Keys Power key Recharge key Standby mode Automatic cleaning 4.1.2 Working mode: 4.1.2.1 Manual mode Automatic recharge 1. Make sure that the batteries of the vacuum cleaner are fully charged, and turn on the machine switch to enter the standby state. 2. When the vacuum cleaner is in the standby state, press the power key, and the vacuum cleaner will start to clean automatically. 3.
4.1.3 Operation guide for SN key indicating light State Display Operation Off Light off 1. Have a long pressing of the 1 key for 3 seconds, and release it when a beep is heard. 2. Turn off the machine power switch. 1. If the power switch is turned on, press the 2 On 3 Clean Light on key. 2. If the power switch is not turned on, turn on the power switch to start the machine. Blue light Press the normally on 4 Search for recharge machine to start cleaning.
4.2 Charging method 4.2.1 Manual charging: High voltage! Please dry your hands before operation for fear of electrical shock! 1. Use the charging dock for charging: First connect the power adapter with the charging dock, then connect with the power supply; put the vacuum cleaner on the charging dock to charge (The blue light of the recharge key flashes during charging, and the blue light is normally on after the battery is fully charged). 2.
5. Product Maintenance 5.1 Clean Tip: Please clean and maintain the vacuum cleaner regularly according to the use conditions. the charging pole pieces Charging pole pieces 1. Please turn off the power switch or unplug the power cord first. 2. Please use a dry cloth to wipe them once a month. 3. Do not scrub with oil. 5.2 Clean the dust box 5.2.1 Install and remove the dust box As shown in the figure above, press the “ dust box. ” key on the dust box to eject the dust box, and then remove the 5.2.
3. Remove the filter assembly and use a cleaning brush to clear away the dust on the filter screen. Cold air Hot air X 4. The inside of the dust box and the filter screen can be flushed under running water. (Note: You need to dry it thoroughly before you can put them back into the vacuum cleaner.) 5. After cleaning, reinstall the filter screen, close the dust box cover, and finally put the dust box into the vacuum cleaner.
5.3 Clean the middle sweeper 5.3.1 Remove the middle sweeper 1. As shown in the figure, push the lock lever to the middle, and lift it up. 2. Grab the middle sweeping brush and lift it up. 3. Remove the middle sweeping scraper assembly and the middle sweeping brush. 5.3.2 Clean the middle sweeping brush 1. As shown in the figure, please use a cleaning brush to clean the middle sweeping soft brush and the middle sweeping rubber brush regularly. 2.
5.4 Clean the side brush 1. Use a screwdriver to remove the screws from the side brush. 5.5 Clean 2. Remove the side brush and clear away the hair and other rubbish on the side brush. Then clear away the entanglements in the slot of the side brush. the wheels Clean the front, left and right wheels regularly with a cleaning brush. (Note: The wheel shaft may be entangled by hair, cloth strips, etc., so please clean it in time.) Bottom view of sensor 5.
6. Troubleshooting Fault indication by light flashing The red light flashes twice, and 1 beep can be heard. The red light flashes 3 times, and 1 beep can be heard. The red light flashes 5 times, and 1 beep can be heard. Fault name Fault description Left wheel fault The left wheel does not rotate, as the left wheel is overloaded. Right wheel fault The right wheel does not rotate, as the right wheel is overloaded. Please check whether the left wheel of the machine gets entangled.
7. Technical Parameters Functional parameters of the host machine Functional parameters of accessories Operating voltage 14.4 V Rated power 24 W Output voltage 19V Battery Lithium battery Output current 600mA Battery capacity 2500mAh Charging time 4-5 hours Operating hours Approx. 100 minutes Working temperature range Power adapter Charging dock Input voltage 19V Remote controller 0°C〜60°C Remote control distance 20m Operating humidity range ≤ 80%RH Batteries AAA (No.
■ Names and contents of harmful substances in the product Harmful Substances Hexavalent chromium (Cr (VI)) Polybrominated biphenyl (PBB) Polybrominated diphenyl ethers (PBDE) 〇 〇 〇 〇 〇 〇 〇 〇 〇 X 〇 〇 〇 〇 〇 Electrical components and control components X 〇 X 〇 〇 〇 Dry batteries X 〇 〇 〇 〇 〇 Rechargeable batteries X 〇 〇 〇 〇 〇 Component Name Lead (Pb) Shell component 〇 〇 Internal plastic parts 〇 Metal parts Mercury Cadmium (Hg) (Cd) This form is prepared in accordan
Warranty Card II User name (II) Settlement form of the warranty provider Address Tel. Postal code Product model Purchase date Invoice number Warranty period Product warranty description: 1. From the date of the user’s purchase of this product, the warranty period is one year for the host machine, and six months for the adapter, rechargeable batteries and other accessories. 2.After receiving the product repair request, the after-sales service staff will solve the problem within 15 working days. 3.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two cond itions: (1) this device may not cause harmful interference, and (2) this device must accept any int e rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could v oid the user's authority to operate the equipment.
