InHand Networks Vehicle Tracker VT310 Quick Installation Manual InHand Networks www.inhandnetworks.com Version: V1.0 February, 2020 Copyright © 2019. All rights are reserved by InHand Networks and its licensors. Without the written permission of the Company, no unit or individual is allowed to excerpt, reproduce or transmit in any form part or all of the contents in the manual.
contents Vehicle Tracker VT310.....................................................................................................................................0 VT310 Vehicle Tracker.....................................................................................................................................2 Quick Start Guide .....................................................................................................................................2 1. Structure of VT310.................
VT310 Vehicle Tracker Quick Start Guide V1.0 1.
2. Installation and Wiring VT310 comes with a built-in battery. The VT310 device can be powered by a built-in battery or an external DC power supply. Generally, when an external DC power supply is available, the external power supply is preferred. LTE antenna and GNSS antenna are built in VT310. Users can use without operation. The information of the LTE Module: Mode Number: EMS31-X, FCC ID: QIPEMS31-X, IC: 7830A-EMS31X 1) Installing the SIM card Before using the device, you need to install the SIM card.
2) Power to VT310 a) Use external power supply Connect the positive and negative terminals of the external power supply with X-V+ and X-V- respectively: b) Use built-in battery for power VT310 provides 1200mAbuilt-in rechargeable battery. When there is no external power input, stable power input can be provided for the equipment. 3. Confirm Work Status 1) Confirm by Indicator Status a) GNSS Indicator（Green） Function Indicator status GPS disable OFF GPS enable FLASH（0.
2) Confirm by Configuration Mode a) Wiring： Serial port (check in device Manager after connecting PC with USB to serial port line) : VT310 devices connect serial ports (cables R232-Tx1, RS232-Rx1, GND connect USB to 232 serial ports) : b) Open the serial port to enter the Configuration Mode： Use “SSCOM42”, click open serial port, enter +++ in the character box, and then click Send.
115200; Data bit: 8; Stop bit: 1; Check bit: None; Asthenosphere control is not supported. ②When sending "+++" into configuration mode, be careful not to check "HEX Send" or "send new line". sscom42.exe The window enters the configuration mode, then closes the serial port.
c) Show work status by commond： i. cellular status commond：cellular status ii. GNSS status Commond：lbs status 4. Connect to Wialon Wialon – the platform for GPS tracking and IoT.
notice：commond to take effect after restart 2) Configuration to Wialon URL https://hosting.wialon.com/ NAME inhand_free PWD evan1234 Add VT310 to the Wialon , Please in the order indicated above.
3) Confirm Wialon connection status 1. By commond Commond：wialon status Connect success：connected Connecting：connecting Connect failed：disabled 2. By Wialon Switch to “Monitor” , When the device is online , it appears green ; When the device goes offline, it appears grey. 5. Notice 1) Parameters of Cellular VT310 supports ordinary card automatic dialing, The default dialing parameter for white CARDS is ”internet auto gprs gprs *99# internet 2 60” .
When the configuration is complete, enter the command“ reboot”to restart the device. ISED STATEMENT This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
FCC warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
RF Exposure Statement This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 21 cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le dispositif est conforme aux limites d 'exposition aux rayonnements fixées pour un environnement non contrôlé.
