DT150 Installation Manual MAEN844D, 2014-02 English
Foreword DT150 Installation Manual Foreword The DT150 industrial monitor is a TFT-LCD touch screen monitor, designed to be mounted in a cabinet and connected to an industrial PC. The monitor is optimized for a maximum resolution of 1024 x 768 pixels when the full display area of the module is used. This manual explains how to install the monitor. Please see www.hmi.beijerelectronics.com for further information.
Foreword Beijer Electronics, MAEN844D
Contents Contents 1 Safety Precautions................................................................................... 5 1.1 General ........................................................................................ 5 1.2 During Use .................................................................................. 6 1.3 Service and Maintenance.............................................................. 6 1.4 Dismantling and Scrapping..........................................................
Contents Beijer Electronics, MAEN844D
Safety Precautions 1 Safety Precautions Both the installer, owner, and operator of the monitor must read and understand this installation manual. 1.1 General – Only qualified personnel may install or operate the monitor. – The monitor must be installed according to the installation instructions.
Safety Precautions 1.2 During Use – Keep the monitor clean. – Emergency stop and other critical safety functions may never be controlled from the monitor. – Do not use force or sharp objects on the display surface. 1.3 Service and Maintenance – Only qualified personnel should carry out repairs. – The agreed warranty applies. – Before carrying out any cleaning or maintenance operations, disconnect the equipment from the electrical supply.
Installation 2 2.1 Installation Space Requirements Installation plate thickness: 1.5 - 9.0 mm (0.06 - 0.35 inch) Space requirements when installing DT150: 50 mm (2.0 inch) 304 mm (11.97 inch) 25 mm (1.0 inch) 45 mm (1.77 inch) 25 mm (1.0 inch) 50 mm (2.0 inch) 50 mm (1.97 inch) 398 mm (15.67 inch) Caution: The openings on the enclosure are for air convection. Do not cover these openings. 2.2 Installation Process 1. Unpack and check the delivery. If anything is damaged, notify the supplier.
Installation 2. Place the panel cut out where the monitor is to be situated, draw along the outer sides of the holes and cut according to the markings. 3. Secure the monitor in position, using all the fastening holes and the provided brackets and screws: x 14 0.5 - 1.
Installation 4. Connect the cables in the specified order. Caution Use only shielded signal cables. Separate high voltage cables from signal and supply cables. A Caution: The monitor must be brought to ambient temperature before it is started up. If condensation forms, ensure that the monitor is dry before connecting it to the power outlet. B Monitor 115/230 V AC Ground connected power cord A B Industrial PC VGA/DVI AC/DC Adaptor 12 V DC + 5.
Installation 10 Beijer Electronics, MAEN844D
Technical Data 3 Technical Data Parameter DT150 Front panel, W x H x D 398 x 304 x 6 mm Mounting depth 50 mm Front panel seal IP 66 Rear panel seal IP 20 Front panel material Touch screen: Polyester on glass *, 1 million finger touch operations. Overlay: Autotex F157 or F207. Powder-coated aluminum. Reverse side material Powder-coated alu-zink. Touch interface Drivers are available at www.microchip.com/pagehandler/en-us/technology/ tsharc/home.html#driversmanuals or at www.beijerelectronics.
Technical Data Parameter DT150 * See section 4 Chemical Resistance 3.1 The On Screen Display Menu The On Screen Display (OSD) menu makes it easy to adjust monitor settings. The buttons for accessing the OSD menu are located on the rear side of the monitor. Some of the OSD buttons have multiple functions (a hot key option), listed below. Usually, the display is configured by the automatic display configuration when pressing the Down Arrow button.
Technical Data 3.1.1 On Screen Menu Descriptions This section describes the accessible sub menus and their functions.
Technical Data Main Menu Sub Menu Image Control Avaliable mode: Analog RGB Main Menu Tool 14 Function Auto Auto configuration of geometry.
Technical Data 3.2 Operation Messages The following operation messages will be displayed under different circumstances: Operation message Explanation AUTO TRACKING Auto Tracking (analog RGB mode): Executes auto function NO SIGNAL Self diagnostics (analog RGB mode): No input signal after power-on with power switch. The message will disappear after 10 seconds of activity of input signal. NO SUPPORT Out of Range: The input signal exceeds the supported range. 3.
Technical Data 3.5 Calibrate the Touch Screen The industrial monitor has a built in touch screen. This is not operational when shipped from the supplier and must be installed. Instructions and drivers for installation of the touch screen function are available at: www.hmi.beijerelectronics.
Chemical Resistance 4 Chemical Resistance 4.1 Metal Casing The frame and casing material is powder-coated aluminum.
Chemical Resistance 4.2 Touch Screen and Overlay 4.2.1 Autotex F157/F207 Autotex F157 or F207 covers the overlay surrounding the touch screen.
Chemical Resistance 4.2.2 Touch Screen Surface The touch screen surface on the monitor withstands exposure to the following solvents without visible change: Solvents Time Acetone 10 minutes Isopropanol 10 minutes Toluene 5 hours 4.2.3 Autoflex EB It is recommended to use the Autoflex EB touch display protection film, that can be ordered from Beijer Electronics. Solvent Resistance Autoflex EB withstands exposure to the same chemicals as Autotex F157 or F207 according to section Autotex F157/F207.
Chemical Resistance 20 Beijer Electronics, MAEN844D
Drawings 5 5.
Drawings 22 Beijer Electronics, MAEN844D
Head office Beijer Electronics AB Box 426 201 24 Malmö, Sweden www.beijerelectronics.
