OmslagMA00856.
Foreword DT1151 Installation Manual Foreword The DT1151 industrial monitor is a TFT-LCD touch screen monitor, designed to be mounted in a cabinet and connected to an industrial PC. The monitor is optimized for a maximum resolution of 1024 x 768 pixels when the full display area of the module is used. This manual explains how to install the monitor.
Contents Contents 1 Safety Precautions................................................................................... 5 1.1 General ........................................................................................ 5 1.2 During Use .................................................................................. 6 1.3 Service and Maintenance.............................................................. 6 1.4 Dismantling and Scrapping..........................................................
Contents Mitsubishi Electric, MA00856
Safety Precautions 1 Safety Precautions Both the installer, owner, and operator of the monitor must read and understand this installation manual. 1.1 General – Only qualified personnel may install or operate the monitor. – The monitor must be installed according to the installation instructions.
Safety Precautions 1.2 During Use – Keep the monitor clean. – Emergency stop and other critical safety functions may never be controlled from the monitor. – Do not use force or sharp objects on the display surface. 1.3 Service and Maintenance – Only qualified personnel should carry out repairs. – The agreed warranty applies. – Before carrying out any cleaning or maintenance operations, disconnect the equipment from the electrical supply.
Installation 2 2.1 Installation Space Requirements Installation plate thickness: 1.5 - 9.0 mm (0.06 - 0.35 inch) Space requirements when installing DT1151: 50 mm (2.0 inch) 304 mm (11.97 inch) 25 mm (1.0 inch) 45 mm (1.77 inch) 25 mm (1.0 inch) 50 mm (2.0 inch) 50 mm (1.97 inch) 398 mm (15.67 inch) Caution: The openings on the enclosure are for air convection. Do not cover these openings. 2.2 Installation Process 1. Unpack and check the delivery. If anything is damaged, notify the supplier.
Installation 2. Place the panel cut out where the monitor is to be situated, draw along the outer sides of the holes and cut according to the markings. 3. Secure the monitor in position, using all the fastening holes and the provided brackets and screws: x 14 0.5 - 1.
Installation 4. Connect the cables in the specified order. A B Caution Use only shielded communication cables. Separate high voltage cables from signal and supply cables. Caution: The monitor must be brought to ambient temperature before it is started up. If condensation forms, ensure that the monitor is dry before connecting it to the power outlet. 5. Carefully remove the laminated film over the monitor display, to avoid static electricity that could damage the monitor.
Installation 10 Mitsubishi Electric, MA00856
Technical Data 3 Technical Data Parameter DT1151 Front panel, W x H x D 398 x 304 x 6 mm Mounting depth 50 mm Front panel seal IP 66 Rear panel seal IP 20 Front panel material Touch screen: Polyester on glass *, 1 million finger touch operations. Overlay: Autotex F250. Powder-coated aluminum. Reverse side material Powder-coated alu-zink. Touch interface Eely ET-RY-USB-VI, via USB. Drivers for Windows 95/98/ME/2000/XP are available. Screen setup Via rear membrane keyboard.
Technical Data 3.1 The On Screen Display Menu The On Screen Display (OSD) menu makes it easy to adjust monitor settings. The buttons for accessing the OSD menu are located on the rear side of the monitor. Some of the OSD buttons have multiple functions (a hot key option), listed below. Usually, the display is configured by the automatic display configuration when pressing the Down Arrow button. If advanced configuration is needed, the Menu button displays other options.
Technical Data 3.1.1 On Screen Menu Descriptions This section describes the accessible sub menus and their functions. Note: The menus Picture and Function are not accessible in DVI-mode. Main Menu Color Main Menu Picture Main Menu Function Sub Menu Function Contrast Adjust contrast.
Technical Data Main Menu Sub Menu OSD Menu Language Select the language of OSD Menu: English/French/German/Spanish/Italian/Danish OSD H.Pos Adjust horizontal position of OSD Menu by value OSD V.Pos Adjust vertical position of OSD Menu by value OSD Timer Set the duration time of the OSD Menu (OSD turn-off time) Translucent Set OSD Menu to translucent or opaque Exit Exit to main menu Main Menu Sub Menu Misc. 3.
Technical Data 3.3 Video Input Timing The following vertical refresh rate is recommended: Mode 1024 x 768 pixels Refresh rate 60~75 Hz Sync.: H/V separated TTL 3.4 Audio Support The industrial monitor has a built in stereo amplifier that can be controlled either via the OSD interface or the OSD buttons on the rear side. The monitor is equipped with one audio input port and one speaker out port.
Technical Data 16 Mitsubishi Electric, MA00856
Chemical Resistance 4 4.1 Chemical Resistance Metal Casing The frame and casing material is powder-coated aluminum. This powder paint withstands exposure of up to 24 hours duration to the following chemicals without visible change: Ammonia 25% Isopropyl alcohol Nitric acid 3% De-ionized water Tap water Chlorhydric acid 10% Butanol Cooling liquid 50% Washer fluid 33% Citric acid 10% Ligroin Sulfuric acid 20% Diesel Cooking oil Turpentine Ethanol 99.
Chemical Resistance 4.2 Touch Screen and Overlay 4.2.1 Autotex F250 Autotex F250 covers the overlay surrounding the touch screen. Solvent Resistance Autotex F250 withstands exposure of more than 24 hours duration under DIN 42 115 Part 2 to the following chemicals without visible change: Potassium ferrocyanide/ ferricyanide Sodium hypchlorite <20% (bleach) 1.1.1.
Chemical Resistance Autotex withstands DIN 42 115 Part 2 exposure of up to 1 hour duration to glacial acetic acid without visible change.
Chemical Resistance 4.2.3 Autoflex EB It is recommended to use the Autoflex EB touch display protection film, that can be ordered from the manufacturer. Solvent Resistance Autoflex EB withstands exposure of more than 24 hours duration under DIN 42 115 Part 2 to the following chemicals without visible change: Potassium ferrocyanide/ ferricyanide Sodium hypchlorite <20% (bleach) 1.1.1.
Chemical Resistance Autoflex withstands DIN 42 115 Part 2 exposure of up to 1 hour duration to glacial acetic acid without visible change.
Chemical Resistance 22 Mitsubishi Electric, MA00856
Drawings 5 5.
Drawings 24 Mitsubishi Electric, MA00856
