brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Description bc-12er The bc-12er is a 12 channel receiver designed for the brixlcontrol system. Supplying 12 universal channels, the bc-12er is the ideal unit for smaller models or trailers. Multiple units can be linked by either cable or infrared connections. The 12 universal channels can be used as an output to drive servos, LED´s or PWM controlled drivers.
brixlelektronik bc-12er – 12 channel receiver ...
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Please read and follow the hints and remarks on the last pages of this manual concerning mounting and power supply! Functionality of outputs Some of the universal outputs can be configured during the programming process as PWM outputs or inputs for sensors etc. Please refer to the shematics below for further details.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver IR = IR LED connector with integrated resistor I = IR sender or receiver D = Display N = Multiswitch/Nautic Module LED1 = Status LED LED2 = Eeprom/Memory access LED3 = Operation indicator Installation The modules must be connected with an antenna and must be supplied with the supply voltage in the assigned range. Please refer to picture 1 and 2 for the correct connection.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Operation status of the module bc-12er Upon delivery output 1 on the module is configured as a status output. A connected LED will show the different states of the module.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver higher. Transmitters with software versions below 1.500 can only access modules with identifier 0! Moduladresse [Module identifier] 0..9 Define a unique identifier for this module Upon delivery all modules will come with 0 Min.Spannung [minimum voltage] 3.5..9.99 The BEC voltage will be monitored and this will define the minimum voltage.
brixlelektronik bc-12er – 12 channel receiver Ausschaltwert [switch off value] Funkabrisswert [fail safe] Wie begrenzen [limtation of signal] ...we got the solution bc-20 plus 20 channel receiver +/- 125% Connected device will set to the programmed position 0 Neutral signal will be provided (1.5ms) Defines the position of the connected device during park mode (choosing and connecting to new model with transmitter) halten [hold] Current position will be held kein Sig.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver AUS % AUS 0..125% Using a potentiomer this can be used to switch of this output at a certain angle of the pot Tempomat This will enable a cruise control option. [Cruise control] Choose an input device (momentary switch recommended) with „Begrenzung mit“ that can control this feature. This feature will work similar to a „real“ car cruise control.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver the stick movement MultiplikatorP [Multiplier positive] 0.2..2.00 Stick movement multiplied with MultiplikatorP is movement of the connected device(positive) MultiplikatorM [MultiplierM] 0.2..2.00 Stick movement multiplied with MultiplikatorM is movement of the connected device(negative) Maximalwert [max. value] -100..125% Maximum output value for the conncted device Minimalwert [Min.value] -125..
brixlelektronik bc-12er – 12 channel receiver Ausschaltwert [switch off value] Funkabrisswert [fail safe] Ebenenschalter [Level control] Ebenenestellung [Level assignment] ...we got the solution bc-20 plus 20 channel receiver +/- 125% Connected device will be set to the programmed position 0 Neutral signal will be provided (1.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Maximalwert [max. value] -100..125% Maximum output value for the conncted device Minimalwert [Min.value] -125..100% Minimum output value for the conncted device Auf.Geschw. [Speed up] 1..200 Maximum speed in up direction Abw.Geschw. [Speed down] 1..200 Maximum speed in down direction Please note that some connected devices may not accept high speeds.
brixlelektronik bc-12er – 12 channel receiver bc-20 plus 20 channel receiver Ausschaltwert Defines the position of the connected device in park mode Current position will be held halten [hold] 1..6 Funkabrisswert [Fail safe] G.Position 1..6 [Gear position] ...we got the solution Set position Defines the position of the connected device when the signal is lost or the transmitter is switched off halten [hold] 1..6 Current position will be held -125..
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver 0 Neutral signal will be provided (1.5ms) Ausschaltwert Defines the position of the connected device during park mode [switch off value] (choosing and connecting to new model with transmitter) Funkabrisswert [fail safe] halten [hold] Current position will be held kein Sig.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver [..Signal off] Offset li [offset left] -125%..+125% Defines the offset of the connected device on the right side Offset re [offset left] -125%..+125% Defines the offset of the connected device on the right side Multip. li [Multiplier left] 0.2..2.00 Stick movement multiplied with Multip.li is movement of the connected device on the left side Multip. re [Multiplier right] side 0.2..2.
brixlelektronik bc-12er – 12 channel receiver Switch 2 E(down) ...we got the solution bc-20 plus 20 channel receiver = Exit 4 USM-RC-2 Beier Soundmodule (please note sequence of the switches) Switch 1 A(up) = Switch 8 up Switch 1 E(down) = Switch 8 down Switch 2 A(up) = Switch 7 up Switch 2 E(down) = Switch 7 down..... Schalter 1..8 [Switch] A..z Which input device shall be used „-“ deactivated Ebenenschalter [Level control] A..
brixlelektronik bc-12er – 12 channel receiver Funkabrisswert [fail safe] Ebeneschalter [Level control] Ebenenestellung [Level assignment] ...we got the solution bc-20 plus 20 channel receiver Defines the status of the output device when the signal is lost or the transmitter is switched off Gemerkt [Memory] Last status of the connected device before switched off Ein [on] Output is on (Hi 3.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver EIN Zeit/Nachlauf [On time] Used with AUS/Zeit for flash options. If AUS Zeit/Pause is defined this option will set the on-time of the output. If AUS/Zeit is set to 0 this value will define the time the output will remain on after the input device is set to off. To simulate a double or triple flash (emergency vehicles) choose either 2Blitz or 3Blitz.
brixlelektronik bc-12er – 12 channel receiver [Fail safe value] ...we got the solution bc-20 plus 20 channel receiver lost or the transmitter switch off Warnbl.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver modules wich are linked with infrared. Please note that input voltages should not be higher than 3.3V. Add a 10k resistor for protection purposes. If an open collector output (e.g. brake lights from ESC) is connected to these inputs, a pull up resistor of 5k to +BEC might be necessary. Auf Kanal n-z [Channel n-z] n..
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver [Current 10] the measurement range of 0..10A(15A peak). Sensor up to 50A upon request. Temp.99 Temperature measurement using the bc-MM-Temp with the measurment range of 0..99.9°C Temp.120 Temperature measurement using the bc-MM-Temp with the measurment range of -20..
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Please note that no infrared receiver should be connected during programming. For programming an antenna or a cable connection must be used. Funktion: Display [Feature: Display] A 0.9“ display can be connected to output 12 to visualize different values. It will display the operating voltage and the values measured by connected sensors.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver [Empf.konfig] [Funkabriss] [geparkt] Receiver in programming mode Connection lost, receiver in fail safe mode Receiver in park mode Vers Version number of hard- (12) and software (417) EinZ Module has been started xx times BSZG Hourmeter total (HH:mm) BSZ Hourmeter depending on a defineable input device. (HH:mm:ss) Input device must be programmed in [Funktion: Status] Feature: Status.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver 23.06.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Remarks: Antenna Never connect or disconnect the antenna while the receiver is powered up! This might destroy the modules. The colour coded cable of the antenna is facing away from the receiver! Mounting Depending on the model and the available space for mounting the module can installed with or without the attached plastic cover. For this purpose we deliver both parts seperately.
brixlelektronik bc-12er – 12 channel receiver ...we got the solution bc-20 plus 20 channel receiver Display/Infrared link The bc-12 plus supports either a display connected to output 12 or the infrared connection . If the display is disabled the infrared connection will be enabled automatically.
