Instruction Manual

These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.
SwiftComm
™
Wireless SSI Interface
SENSOR TYPE:
SS = SSI Absolute Encoder
MOUNTING:
PM1 = 2, 1/4–20 tapped holes
OUTPUT VOLTAGE
FROM SENSOR:
5 = 5 VDC
SENSOR TYPE:
SS = SSI Absolute Encoder
MOUNTING:
PM1 = 2, 1/4 – 20 tapped holes
OUTPUT TYPE:
28V/V = 5-28V
in/out
OUTPUT
TERMINATION:
M18 = MS3101F18-1P
SwiftComm Ordering Options for assistance call 800-350-2727
Order Note: The Transmitter and Receiver are sold as pairs. Sensor type must be the same for Transmitter and Receiver modules
TRANSMITTER MODEL NUMBER
RECEIVER MODEL NUMBER
TX SS PM1 5
RX SS PM1 28V/5 M18
SCS120-M18
Receiver includes antenna. Mating cable assemblies are available.
Now the machine designer is free to install
sensor equipment without the expense and
constraints of a hard-wired system. Encoder
installations in difficult applications like
cranes, rotating tables or mobile applications,
are greatly simplified. The SwiftComm system
includes the transmitter-receiver pair, which
communicates using a point-to-point frequen-
cy-hopping 2.4 GHz RF protocol. Because
of its flexible input/output electronics, it can
interface with many different industrial sen-
sors and control systems. Simply connect the SwiftComm transmitter to the
sensor and the SwiftComm receiver to your control system and apply power.
That’s it! No complicated cabling required.
SwiftComm’s proprietary radio protocols include a broad security code range,
data encryption, handshaking, interference recovery, and error checking that
together provides a secure and robust wireless interface system. Ruggedness
and flexibility are further enhanced with SwiftComm’s NEMA 4 weatherproof
enclosures, panel mounting options, antenna choices and wide-range DC
power inputs.
Tel: [phone]
Fax: [phone]
7230 Hollister Ave., Goleta, CA 93117-2807
www.beisensors.com
• Robust Signal
• Real-Time Control
• Secure Transmission
• Long Range
SwiftComm’s Unique Advantages
Electrical Specifications
Supply Voltage (transmitter or receiver):
5 to 28 VDC (see model number)
Supply Current (transmitter or receiver):
220 mA Max
Output Format:
Transmitter and Receiver I/O: SSI Clock & Data
Temperature: Operating: -40° to 70°,
Storage: -40° to 100°
Rf Specifications
RF Power Output: 17 dBm (50 mW) Nominal
Frequency Range: 2.4 GHz ISM Band
Adaptive Frequency Hopping Protocol
Sensitivity: -80 dBm (0.1% BER @
1000kbps)
Antenna Connector: TNC – Reverse Polarity
(50 Ohm)
Transmission Range: 300 Meters (5.5 dBi
Gain “Rubber Duck” Swivel Antenna, antenna
mounted directly to enclosure)
Encryption: Proprietary enhanced 40-bit
encryption with pseudo-random frequency hop-
ping sequence.
Security Codes: 5 Byte range (>500 billion
unique codes)
Output Specifications
Frequency Response:
SSI Transmitter Frequency: 100KHz (Fixed)
SSI Receiver Frequency: 100KHz to 1.8MHz
Link Update Rate: 600 uS
Signal Loss Time without Link Failure:
120 mS
Transmission Response Time: 1ms typical
Mechanical Specifications
Dimensions: (mm, including Antenna Connector)
Transmitter (excluding cable set): 75W x 98L x 53H
Receiver: 75W x 119L x 53H
Weight:
Transmitter with 10-foot cable (no antenna):
911 grams
Receiver (no antenna): 455 grams
Enclosure: NEMA 4 cast aluminum, powder
coated, gasketed closure intended for indoor or
outdoor use. Protected against windblown dust
and rain, splashing water, hose directed water
and by the formation of ice on the enclosure.
Mounting Options: Two 1/4 - 20 tapped
holes on back of enclosure for mounting to
flat surface. Optional mounting ears or DIN
rail kit available.
Specification No. 02107-002 Rev.11-11
A whole
new era in
wireless
industrial
control
INPUT TERMINATION:
SCS120-M18 = 10’ Cable Assy
SCS120 = 10’ Pigtail
Varying cable length available, consult factory
Transmitter includes antenna and pigtail or connector assembly.
Power cable ordered separately.