Quick Start Guide

54 VOCODER VC340 Quick Start Guide 55
VOCODER VC340 Special Modes VOCODER VC340 Modos Especiales
VELOCITY
The keyboard velocity can be set to a xed value, or
a value that varies dynamically with how hard the
keys are struck. The following procedure shows how
to change the velocity:
1. Turn o the Power.
2. Hold down both ENSEMBLE switches while
turning on the power.
3. If all the LEDs blink fast, then the current
velocity is a xed value (127). The loudness
of the notes will not change if the keys are
pressed soft or hard.
4. If all the LEDs blink slowly, then the current
velocity will vary dynamically. The loudness
of the notes will vary if the keys are pressed
soft or hard.
5. Release the two ENSEMBLE switches and the
VC340 will save the current setting.
6. To change to the other setting, repeat steps
1 and 2.
MIDI Channel
The MIDI transmit and receive channel numbers can be
selected from 1 to 16, using the following procedure:
1. Turn o the Power.
2. Hold down both the STRINGS section UPPER
and LOWER switches, while turning on
the power.
3. All LEDs should ash 3 times fast, showing
that the VC340 is in its MIDI channel
setting mode.
4. Release the STRINGS switches.
5. To rst set the MIDI RX channel, set the
OCTAVE switch to HIGH.
6. The 8 VOCODER and HUMAN VOICE switches
are used to select the channel numbers
as follows:
7. If the STRINGS LOWER switch is selected, the
8 switches represent channel numbers 1 to 8.
8. If the STRINGS UPPER switch is selected, the 8
switches represent channel numbers 9 to 16.
9. Select the required channel number.
10. To set the MIDI RX channel to ALL, press and
hold both ENSEMBLE switches. (This is only
available in RX, so the VC340 can receive
incoming MIDI from all channels.)
11. To select the MIDI TX channel, rst set the
OCTAVE switch to LOW, and repeat steps
6 to 9 above.
12. To exit, press both the STRINGS UPPER
and LOWER switches at the same time.
The channel numbers will be saved, and the
VC340returned to normal operation.
Examples
To set MIDI RX to channel 3:
13. OCTAVE switch HIGH
14. STRINGS LOWER ON
15. VOCODER ENSEMBLE switch ON
16. Press STRINGS UPPER and LOWER at the same
time to exit
To set MIDI TX to channel 10:
17. OCTAVE switch LOW
18. STRINGS UPPER ON
19. VOCODER UPPER switch ON
20. Press STRINGS UPPER and LOWER at the same
time to exit
To set MIDI RX to ALL:
21. OCTAVE switch HIGH
22. Press both ENSEMBLE switches at the same
time. All 8 LEDs will be on.
23. Press STRINGS UPPER and LOWER at the same
time to exit
1 2 3 4 5 6 7 8
ON
ON
Vocoder Human Voice Strings
MIDI Channel number selection
Set HIGH when adjusting MIDI RX channel
Set LOW when adjusting MIDI TX channel
9 10 11 12 13 14 15 16
MIDI RX MIDI TX
VELOCIDAD
La velocidad del teclado se puede establecer en un
valor jo o en un valor que varía dinámicamente con
la fuerza con la que se pulsan las teclas. El siguiente
procedimiento muestra cómo cambiar la velocidad:
1. Apague la energía.
2. Mantenga presionados ambos interruptores
ENSEMBLE mientras enciende la unidad.
3. Si todos los LED parpadean rápidamente,
entonces la velocidad actual es un valor jo
(127). El volumen de las notas no cambiará si
las teclas se presionan suave o fuerte.
4. Si todos los LED parpadean lentamente,
la velocidad actual variará dinámicamente.
El volumen de las notas variará si las teclas se
presionan suave o fuerte.
5. Suelte los dos interruptores ENSEMBLE y el
VC340 guardará la conguración actual.
6. Para cambiar a la otra conguración, repita
los pasos 1 y 2.
Canal MIDI
Los números de canal de transmisión y recepción
MIDI se pueden seleccionar del 1 al 16, mediante el
siguiente procedimiento:
1. Apague la energía.
2. Mantenga presionados los interruptores
UPPER e LOWER de la sección STRINGS
mientras enciende la unidad.
3. Todos los LED deberían parpadear 3 veces
más rápido, mostrando que el VC340 está en
su modo de ajuste de canal MIDI.
4. Suelta los interruptores STRINGS.
5. Para congurar primero el canal MIDI RX,
ajuste el interruptor OCTAVE en HIGH.
6. Los 8 interruptores VOCODER y HUMAN VOICE
se utilizan para seleccionar los números de
canal de la siguiente manera:
7. Si se selecciona el interruptor STRINGS
LOWER, los 8 interruptores representan los
números de canal del 1 al 8.
8. Si se selecciona el interruptor STRINGS UPPER,
los 8 interruptores representan los números
de canal del 9 al 16.
9. Seleccione el número de canal requerido.
10. Para establecer el canal MIDI RX en TODOS,
mantenga presionados ambos interruptores
ENSEMBLE. (Esto solo está disponible en
RX, por lo que el VC340 puede recibir MIDI
entrante de todos los canales).
11. Para seleccionar el canal MIDI TX, primero
ponga el interruptor OCTAVE en LOW y repita
los pasos 6 a 9 anteriores.
12. Para salir, presione los interruptores STRINGS
UPPER y LOWER al mismo tiempo. Los
números de canal se guardarán y el VC340
volverá al funcionamiento normal.
Ejemplos
Para congurar MIDI RX en el canal 3:
13. Interruptor de OCTAVA ALTA
14. CUERDAS ABAJO
15. ENSEMBLE DE VOCODER ENCENDIDO
16. Presione STRINGS UPPER y LOWER al mismo
tiempo para salir
Para congurar MIDI TX en el canal 10:
17. Interruptor OCTAVE BAJO
18. CUERDAS SUPERIORES EN
19. Interruptor VOCODER SUPERIOR ENCENDIDO
20. Presione STRINGS UPPER y LOWER al mismo
tiempo para salir
Para establecer MIDI RX en TODOS:
21. Interruptor de OCTAVA ALTA
22. Presione ambos interruptores ENSEMBLE al
mismo tiempo. Los 8 LED estarán encendidos.
23. Presione STRINGS UPPER y LOWER al mismo
tiempo para salir
1 2 3 4 5 6 7 8
ON
ON
Vocoder Human Voice Strings
MIDI Channel number selection
Set HIGH when adjusting MIDI RX channel
Set LOW when adjusting MIDI TX channel
9 10 11 12 13 14 15 16
MIDI RX MIDI TX