BASS PROCESSOR SONIC EXCITER BASS PROCESSOR SONIC EXCITER SX3040 MIN MAX DRIVE MIN MAX TUNE MIN MAX MIX MIN MAX TUNE MIN MAX HARMONICS MIN 1 2 IN/OUT IN/OUT MAX MIX MIN MAX DRIVE MIN MAX TUNE User Manual SONIC EXCITER SX3040 Ultimate Stereo Sound Enhancement Processor MIN SONIC EXCITER MAX MIX MIN MAX TUNE MIN MAX HARMONICS MIN MAX MIX POWER
SONIC EXCITER SX3040 User Manual Table of Contents Thank you........................................................................ 2 Important Safety Instructions....................................... 3 Legal Disclaimer.............................................................. 3 Limited Warranty............................................................ 3 1. Introduction................................................................ 5 1.1 Before you get started..................................
SONIC EXCITER SX3040 User Manual Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
SONIC EXCITER SX3040 User Manual “Support” at behringer.com. If your country is not listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at behringer.com. Alternatively, please submit an online warranty claim at behringer.com BEFORE returning the product. All inquiries must be accompanied by a description of the problem and the serial number of the product.
SONIC EXCITER SX3040 User Manual 1. Introduction 1.1.2 Initial operation Often used in the past to compensate for the inadequacies of analogue technology, the exciter in today’s Digital Age is a secret weapon of sound engineers for generating contemporary productions that truly stand out. You can now experience this exciting circuit with the SX3040. The unit works with two independent channels, so you can selectively process stereo or two mono signals separately from each other.
SONIC EXCITER SX3040 User Manual SONIC EXCITER (8) POWER: Use the POWER switch to put the unit into operation. The POWER switch should be in the “Off” position when you connect the unit to the power feed (mains). (4) TUNE: Sets the cut-off frequency at which the harmonic exciter starts working. The control range is from 1.3 kHz (MIN) to 10 kHz (MAX). To disconnect the unit from the mains, pull out the power plug. When switching on the unit ensure that the power plug is easily accessible.
SONIC EXCITER SX3040 User Manual 3.2.1 Series cable connection (Insert mode) B1220 PRO The simplest form of series connection consists of a signal chain in which several devices are connected in a row, e.g. keyboard effects unit (SX3040) amplifier. An input signal is fed into the effects unit (SX3040) and a mixed signal consisting of an input signal and a processed effect signal is sent to an amplifier or a recording device (MD recorder, computer etc.) for reproduction.
SONIC EXCITER SX3040 User Manual 3.2.4 Studio application 3.2.5 Stage operation with instrument amplifiers In a studio environment the SONIC EXCITER is ideal for mastering to enhance the sound of recordings. The SX3040 can lend your music the professional polish of high-quality productions in just a few steps. Even if you primarily work with a digital audio workstation, you can perform the final mastering with the SX3040 and an external recorder.
SONIC EXCITER SX3040 User Manual 3.3 Basic operation Due to the small number of SX3040 controls, this is an easy processor to operate. Unbalanced ¼" TS connector strain relief clamp Perform the following steps: sleeve 1) Connect the unit according to the application as described in section 3.2. tip ◊ First make the following settings for one channel (channel 1 or 2 depending on input assignment). For stereo applications choose the same settings for the second channel.
SONIC EXCITER SX3040 User Manual 4.2.2 Connection with insert cables Use standard ¼" insert cables to connect the SONIC EXCITER to the insert path of a mixing console. These Y cables have two ¼" TS connectors at one end, and one ¼" TRS connector at the other. Connect the plug marked “Send” to the INPUT L jack on the effects unit. Connect the “Return” plug to the OUTPUT L jack on the device. Connect the TRS connector to the insert jack of the channel strip on the mixing console.
SONIC EXCITER SX3040 User Manual Dimensions/Weight Dimensions (H x W x D) approx. 8.54 x 1.8 x 19" approx. 217 x 44.5 x 483 mm Weight approx. 5.1 lbs / 2.30 kg BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.
We Hear You
