Quick Start Guide

74 MS-1 Quick Start Guide 75
CHANGING THE PARAMETERS
The parameters may be changed using the following procedure:
1. Press SHIFT+ HOLD/REST + 8 to enter the setting mode. The LOCATION LED 1 will blink yellow.
2. Press <KYBD or STEP> to select pages 1 to 5. The yellow LOCATION LED, shows the current page:
3. Page 1 allows you to select the MIDI input channel, 1 to 16.
4. Page 2 allows you to select the MIDI output channel, 1 to 16.
5. Page 3 allows you to select the clock source mode from 1 to 5: (INTERNAL / MIDI DIN / MIDI USB / TRIG / AUTO). When using AUTO, the clock priority is:
TRIG > MIDI USB > MIDI DIN > INTERNAL
6. Page 4 allows you to select the clock type mode, 1 to 4: (1PPS / 2PPQ / 24PPQN / 48PPQN)
7. Page 5 allows you to select the clock edge mode, 1 to 2: (Fall / Rise)
8. Press STEP switches 1 to 8 to select numeric values from 1 to 8. The current value is indicated by a green LOCATION LED.
9. To access values 9 to 16, press SHIFT + STEP switch 1 to 8. The current value is shown by a red LOCATION LED.
Note: If a setting is on the same LED number as the current page LED, then the LED will ash alternately between the yellow page color and the green or red
parameter color.
10. Press SHIFT + HOLD/REST + 8 to exit the setting mode, and save any parameter changes.
11. More parameters can be changed using the Synthtool App.
CAMBIANDO LOS PARAMETROS
Los parámetros se pueden cambiar mediante el siguiente procedimiento:
1. Presione SHIFT + HOLD / REST + 8 para ingresar al modo de conguración. El LED DE UBICACIÓN 1 parpadeará en amarillo.
2. Presione <KYBD o STEP> para seleccionar las páginas 1 a 5. El LED de UBICACIÓN amarillo muestra la página actual:
3. La página 1 le permite seleccionar el canal de entrada MIDI, 1 a 16.
4. La página 2 le permite seleccionar el canal de salida MIDI, del 1 al 16.
5. La página 3 le permite seleccionar el modo de fuente de reloj de 1 a 5: (INTERNAL / MIDI DIN / MIDI USB / TRIG / AUTO). Cuando se usa AUTO, la prioridad del reloj
es: TRIG> MIDI USB> MIDI DIN> INTERNAL
6. La página 4 le permite seleccionar el modo de tipo de reloj, 1 a 4: (1PPS / 2PPQ / 24PPQN / 48PPQN)
7. La página 5 le permite seleccionar el modo de borde del reloj, 1 a 2: (caída / subida)
8. Presione los interruptores STEP del 1 al 8 para seleccionar valores numéricos del 1 al 8. El valor actual se indica mediante un LED de UBICACIÓN verde.
9. Para acceder a los valores del 9 al 16, presione SHIFT + STEP, cambie del 1 al 8. El valor actual se muestra mediante un LED rojo de UBICACIÓN.
Nota: If a setting is on the same LED number as the current page LED, then the LED will ash alternately between the yellow page color and the green or red
parameter color.
10. Press SHIFT + HOLD/REST + 8 to exit the setting mode, and save any parameter changes.
11. More parameters can be changed using the Synthtool App.
Attack
Time
Decay
Time
Sustain Level
Time
Env
Level
Key
Gate
Release
Time
Key Pressed Key Released
Attack
Time
Decay
Time
Sustain Level
Time
Env
Level
Key
Gate
Release
Time
Key Pressed Key Released
ADSR Envelope
The stages of the ADSR envelope are shown in this simplied diagram
below. The envelope can control the VCA level, the VCF cut-o frequency,
and Pulse Width modulation of the VCO.
ADSR Sobre
The stages of the ADSR envelope are shown in this simplied diagram
below. The envelope can control the VCA level, the VCF cut-o frequency,
andPulse Width modulation of the VCO.
MS-1 Parameters Select MS-1 Seleccionar parámetros