Quick Start Guide

12 MONOPOLY
快速启动向导
13
MONOPOLY SynthTool
MONOPOLY 系统独家数据表
"Synthtool.exe" 应用程序允许您选择 MIDI 通道编号并设置和调整 MONOPOLY 的各种参数以满足您的喜好。
通过 USB 将 MONOPOLY 连接到您的计算机并运行应用程序 （PC 或 MacOS）。
定期查看我们的网站， 了解 SynthTool.exe 或 MONOPOLY 文档的任何更新。
典型的 SynthTool 屏幕
注意: 对于 OUTPUT 参数，选项为 MIDI (DIN), MIDI (USB) 或 BOTH。
还可以通过 MIDI 系统专用 (SysEx) 命令访问参数。 请参阅下面显示的信息。
"Synthtool.exe" 应用程序允许您选择 MIDI 通道编号并设置和调整 MONOPOLY 的各种参数以满足您的喜好。
还可以通过 MIDI 系统专用 (SysEx) 命令访问参数。 请参阅下面显示的信息。
通过 SYSEX 设置值
使用以下数据格式通过 SysEx 消息设置全局值。
F0 00 20 32 00 01 0c aa bb cc D0 … Dn F7
00 20 32 = 制造商 SYSEX ID 号 (Behringer GmbH)
00 01 12 = MONOPOLY 的模型 ID
aa = 设备 ID: 00-0x7F （必须匹配硬件设备 ID）， 或 0x00 以寻址所有设备。
bb = 包号
cc = 子数据包编号 （某些消息可能不存在）。
D0..Dn = 数据包有效载荷
包号
SysEx 数据包
职能 笔记 默认
0E F0 00 20 32 00 01 12 DID 0E 01 nn mm F7 Set MIDI channel nn = Midi TX channel number to be set, range from [0-15]
mm = Midi RX channel number to be set, range from [0-16], 16 = All channel.
nn = [0]
mm = [0]
0F F0 00 20 32 00 01 12 DID 0F nn F7 Set MIDI IN Transpose nn = transpose value [0-24]. Transpose range is -12 to + 12, so 12 is no transpose. [1]
10 F0 00 20 32 00 01 12 DID 10 nn mm pp F7 Set velocity info nn = Key velocity of note on, 1 – 127 is a xed value of velocity;
0 is dynamic velocity.
mm = Key velocity of note o, 1 – 127 is a xed value of velocity;
0 is dynamic velocity.
pp = velocity Curve: 0 - SOFT, 1 - MED, 2 - HARD
nn = [0],
mm = [0],
pp = [0]
12 F0 00 20 32 00 01 12 DID 12 nn F7 Set key priority [0-LOW, 1- HIGH, 2-LAST] [2 - LAST]
15 F0 00 20 32 00 01 12 DID 15 nn F7 Set modulation curve. nn = curve [0-SOFT, 1-MED, 2-HARD] [0- SOFT]
19 F0 00 20 32 00 01 12 DID 19 nn F7 Set external clock polarity. nn = [0—FALL, 1—RISE], [1—RISE]
1A F0 00 20 32 00 01 12 DID 1A nn F7 Set sync clock rate nn = [0 – 1 PPS, 1 – 2 PPQ, 2 – 24 PPQ, 3- 48 PPQ] [2--24 PPQ]
1B F0 00 20 32 00 01 12 DID 1B nn F7 Set sync clock source. nn = [0 – Internal, 1 – MIDI DIN, 2 – MIDI USB, 3 – TRIG] [0 – Internal]
21 F0 00 20 32 00 01 12 DID 21 nn F7 Set MIDI output of
modulation wheel
nn = [0—OFF, 1—MIDI DIN, 2—MIDI USB, 3-BOTH] [3-BOTH]
22 F0 00 20 32 00 01 12 DID 22 nn F7 Set MIDI output of
pitch wheel
nn = [0—OFF, 1—MIDI DIN, 2—MIDI USB, 3-BOTH] [3-BOTH]
23 F0 00 20 32 00 01 12 DID 23 nn F7 Set MIDI output of
keyboard
nn = [0—OFF, 1—MIDI DIN, 2—MIDI USB, 3-BOTH] [3-BOTH]
26 F0 00 20 32 00 01 12 DID 26 nn F7 Set MIDI output of
arpeggiator
nn = [0—OFF, 1—MIDI DIN, 2—MIDI USB, 3-BOTH] [3-BOTH]
27 F0 00 20 32 00 01 12 DID 27 nn F7 Set glide option nn = [0-Improved, 1-Original] [1-Original]
7D F0 00 20 32 00 01 12 DID 7D F7 Restore factory settings
命令示例
命令表
命令 功能
F0 00 20 32 00 01 12 00 0E 01 03 04 F7 Set MIDI channel:
TX channel = 0x3,
RX channel = 0x4
F0 00 20 32 00 01 12 00 0F 18 F7 Set MIDI IN Transpose +12 (+1 Octave)
F0 00 20 32 00 01 12 00 10 00 30 00 F7 Set velocity:
Velocity Note On = dynamic.
Velocity Note O = 48
Velocity Curve = SOFT
F0 00 20 32 00 01 12 00 12 01 F7 Set key priority = High
F0 00 20 32 00 01 12 00 15 02 F7 Set modulation curve = HARD
F0 00 20 32 00 01 12 00 19 00 F7 Set external clock polarity FALL.
F0 00 20 32 00 01 12 00 1A 02 F7 Set sync clock type 24PPQ
F0 00 20 32 00 01 12 00 1B 02 F7 Set sync clock source as USB
F0 00 20 32 00 01 12 00 21 00 F7 Set MIDI output of modulation wheel as OFF
F0 00 20 32 00 01 12 00 22 01 F7 Set MIDI output of pitch wheel as MIDI DIN
F0 00 20 32 00 01 12 00 23 02 F7 Set MIDI output of keyboard as MIDI USB
F0 00 20 32 00 01 12 00 26 02 F7 Set MIDI output of arpeggiator as MIDI USB
F0 00 20 32 00 01 12 00 27 01 F7 Set glide option as Original
F0 00 20 32 00 01 12 00 7D F7 Restore factory settings