User Manual

behringer.com
18 VIRTUALIZER 3D FX2000 User Manual
STOR: On the fifth page, you can select the Store Enable mode. In the “ON” •
mode, the VIRTUALIZER PRO receives controller 112 as the direct storage
command—the current settings are stored on the program location
corresponding to the controller value without waiting for a confirmation.
In the “OFF” mode, controller 112 is ignored.
CAUTION: The Store Enable mode is aimed to transfer several presets ◊
at once from an external PC to the VIRTUALIZER PRO (see also
chapter 5.1). In this mode, you can very easily overwrite your program
locations by unintentionally sending controller 112 values to the
FX2000! Therefore, we strongly recommend to switch off this mode
immediately after use. When the FX2000 is switched on, this mode is
automatically set to off (“OFF”).
DUMP: Select the System Exclusive mode (“SysEx”) using the sixth page. •
In this mode, the FX2000 is ready to “dump” its complete storage content,
including all settings, to a MIDI sequencer. Start your MIDI sequencer and
turn the JOG WHEEL. The data transfer is indicated by “GO”.
DR.EN: In this mode, the FX2000 can receive SysEx data from another MIDI •
device. To load this data, turn the JOG WHEEL slightly so that the DISPLAY
blinks. Start your sequencer, and all of your settings, including preset
parameter settings, are received by your VIRTUALIZER PRO. Data transfer
is interrupted by turning the JOG WHEEL slightly so that “----” appears in
the display.
During a SysEx data transfer, all audio functions of the VIRTUALIZER PRO ◊
are inactive.
INPUT mode3.6.2
With the help of the 2nd EDIT CONTROL, you can specify whether your FX2000
works as a mono (“MONO”) or a stereo unit (“STER”). In mono mode, input 1
is used exclusively. Since the VIRTUALIZER PRO is a real “True Stereo” device,
the DSP processes the signal for many effects separately for both channels
(see chapter 7.1). For effects 13 - 15 and 38, right and left channel parameters can
even be edited separately.
For effects 42 - 44, 58, and 59, a signal must be present at both inputs ◊
for optimal stereo results.
OUTPUT mode3.6.3
Use the 3rd EDIT CONTROL to determine the FX2000’s OUTPUT mode.
The selection of settings depends on your FX2000’s application. If you’re using
the VIRTUALIZER PRO in connection with a mixing console (aux bus), activate the
Mix External (“EXTN”) output mode. The FX2000’s output signal is then
100% wet.
If you’re using the FX2000 with a guitar amplifier that has an effects loop,
select the Mix Internal (“INTN”) output mode. Then, use the MIX/BYPASS control
to adjust the effect volume. For further information, see chapters 4.2 and 4.4.
Dual engine configuration (CONFIG)3.6.4
You can use the 4th EDIT CONTROL to decide how the FX2000’s effects
combinations (presets 61 - 71) should be structured. Since the FX2000 is a true
Dual Engine unit, you can choose between serial 1 (“SER1”), serial 2 (“SER2”)
and parallel (“PARA”). See fig. 3.1, 3.2 and 3.3 to understand how these settings
influence the composition of the effects combinations.
In the example of preset 61 (chorus & reverb), you can decide, whether the
chorus and reverb effects run separately from each other or whether the signal,
treated by the chorus, passes the reverb effect.
Restoring the factory presets3.7
To restore the FX2000 to its preset factory state, press and hold the STORE and
PRESET keys while switching on the unit. “INIT” appears in the DISPLAY and
counting takes place from R 1 to R 100.
This overwrites all changes you have made and restores the ◊
factory presets!
Applications4.
The BEHRINGER VIRTUALIZER PRO is a flexible unit that can be used in various
applications. Prior to a presentation of the FX2000’s many uses, please note the
following remarks on how to set signal levels correctly.
Level setting4.1
Take care to set all levels properly on the FX2000! Low levels deteriorate
the dynamics of the music signal, which results in a poor, weak and noisy
sound. On the other hand, excess levels overdriving the converters in the
VIRTUALIZER PRO should also be avoided. Digital distortion is (unlike its
analog counterpart) extremely unpleasant, since it does not occur gradually
but abruptly.
Please use the OPERATING LEVEL switch and the input level meter of the FX2000.
Make sure that the Clip LEDs flickers only rarely. Ensure that they never light up
all the time!
Using the VIRTUALIZER PRO in the aux bus4.2
Using the FX2000 in the aux bus lets you feed signals from one, several or
all channels of your console into the VIRTUALIZER PRO. When miking a drum
kit, for example, you can use the aux controls to adjust the reverberation
independently for each channel. Thus, you are able to assign a strong reverb
to the snare rather than the toms. Cabling the VIRTUALIZER PRO in the aux bus
should be carried out as follows:
In L In R Out L Out R
AUX Send
1 (& 2)
AUX
Return
Fig. 4.1: Wiring aux busses