User Manual

22 DeepMind 12 User Manual
7.2.3 SELECTING FX MODE
To select an e ects MODE make sure that the '<' symbol is highlighted next to
the e ects MODE symbol, then you can either turn the rotary knob, or use the
data entry fader to select from one of the following routings.
INSERT - In this con guration the e ects slots are placed as INSERT e ects into
the signal  ow of the synthesizer outputs.
SEND - In this con guration the synthesizer output signals are SENT to the e ects
slots and the returned into the signal  ow of the synthesizer outputs.
BYPASS - In this con guration the e ects are bypassed.
7.2.4 SELECTING FX
To load an e ect into a slot, make sure that the '<' symbol is highlighted next to
the slot you wish to use. Then you can either turn the rotary knob, or use the data
entry fader to select from one of the following e ects:
No Name Type
1 TC-DeepVRB Reverb
2 Ambience Reverb
3 Room Rev Reverb
4VintageRev Reverb
5 Hall Rev Reverb
6 Chamber Rev Reverb
7Plate Rev Reverb
8 Rich Plate Reverb
9Gated Rev Reverb
10 Reverse Reverb
11 ChorusVerb Reverb
12 DelayVerb Reverb
13 FlangeVerb Reverb
14 4Band EQ Processing
15 Enhancer Processing
16 FairComp Processing
17 MulBndDist Processing
18 RackAmp Processing
19 EdisonEX1 Processing
20 Auto-Pan Processing
21 NoiseGate Processing
22 Delay Delay
23 3TapDelay Delay
24 4TapDelay Delay
25 T-RayDelay Delay
26 DecimDelay Delay
27 ModDlyRev Delay
28 Chorus Creative
29 Chorus-D Creative
30 Flanger Creative
31 Phaser Creative
32 MoodFilter Creative
33 Dual Pitch Creative
34 RotarySpkr Creative
When you stop on an e ect it is automatically loaded into the chosen slot.
Warning: If you have made edits to any of the parameters within an e ect you
will be shown a pop-up warning dialog (unless dialogs are disabled in the
GLOBAL MENU):
If you need to save your changes, press the -NO switch and then WRITE the
PROGRAM as described in the chapter on writing programs.
If you don't need to save your changes, press the +/YES switch and continue
selecting a new e ect.
7.2.5 CONTROLLING MIX / LEVEL
To adjust the MIX parameters make sure that the '<' symbol is highlighted next to
the word MIX on the e ect slot you want to adjust. Then you can either turn the
rotary knob, or use the data entry fader to change the value.
7.2.6 CONTROLLING LEVEL
To adjust the LEVEL parameters make sure that the '<' symbol is highlighted next
to the word LEVEL on the e ect slot you want to adjust. Then you can either turn
the rotary knob, or use the data entry fader to change the value.
Note: Not all e ects have a MIX parameter as it is only used on e ects which
are marked as "Processing" types in the E ects List. Also, be aware that the MIX
parameter seen on the FX OVERVIEW and the MIX parameter in the FX editing
pages are the same parameter and are shown in both pages for convenience.
If the either the MIX or LEVEL parameter is not available you will see the "--"
symbols in the FX OVERVIEW screen.
7.2.7 FX PAGES1-4
Each of the e ects pages show individual controls for each e ect slot. There are
up to 12 parameters per slot, depending on the e ect which is loaded.
Note: To access successive FX pages simply press the same switch again to cycle
through the pages.
7.2.8 ADJUSTING EFFECTS PARAMETERS
To navigate to the parameter you wish to adjust, use the UP/DOWN/+/- switches.
The selected parameter will be highlighted in black and its detail shown on the
bottom of the screen. To adjust a parameter you can either turn the rotary knob,
or use the data entry slider.
Note: For detailed information on all e ects and their parameters please consult
the EFFECTS LIBRARY section later in this document.