Manual

59 DeepMind 6 User Manual
• RATE - This option is the same as the physical LFO RATE fader on the surface.
Any changes to the LFO RATE fader will be reected here.
The LFO RATE range is from 0 to 255, with 0 being 0.05371 Hz and 255 being
65.4 Hz. The default LFO RATE setting is 0.
Note: When the ARP-SYNC is ON, the RATE parameter is not shown,
but CLOCK-DIVIDE instead. This menu shows values that are based on the
time division of the Master BPM RATE as shown below:
Note: For a timing diagram please consult the section later in
this document.
RATIO DESCRIPTION
4 Four notes
3 Three notes
2 Two notes
1 One note
½ Half note
⁄ Dotted quarter note
⁄ Third note (Half note triplets)
¼ Quarter note
⁄ Dotted eighth note
⁄ Sixth note (Quarter note triplets)
⁄ Eighth note
⁄ Dotted sixteenth note
⁄ Twelfth note (Eighth note triplets)
⁄ Sixteenth note
⁄ Dotted thirty-second note
½ Twenty-fourth note (Sixteenth note triplets)
⁄ Thirty-second note
⁄ Dotted sixty-fourth note
¼ Forty-eighth note (Thirty-second note triplets)
⁄ Sixty-fourth note
• KEY SYNC - This option allows you to turn Key Synchronisation On or O.
When KEY-SYNC is On, the LFO waveform generation will be reset as you
strike a note (keeping in mind the LFO DELAY TIME is also part of the
waveform generation). When KEY-SYNC is O, the LFO will free run.
The default KEY-SYNC setting is O.
• ARP SYNC - This option allows you to turn Arpeggiator Synchronisation On
and O. When ARP-SYNC is On, the LFO waveform will synchronize to the
Master BPM. When ARP-SYNC is o, the LFO will run at the rate set by the
LFO RATE fader parameter.
The default ARP-SYNC setting is O.
• SLEW-RATE - This option allows you to smooth out the transitions of the
LFO waveform. The SLEW RATE reduces the rate of change of the LFO
waveform shape.
The SLEW RATE range is from 0-255, with 0 being no change, and 255
full smoothing.
The default SLEW RATE setting is 0.
• PHASE - As each voice has independent LFOs, this option allows you to
control the phase relationship between the LFO waveforms.
• POLY - All voices use an independent LFO. This is the default mode.
• MONO - All voices use a common LFO.
• SPREAD - With a setting of 1, there is a 1 degree shift between the LFOs
for each voice. As you begin to increase the SPREAD value, the phase of
the LFO for each consecutive voice will be shifted by the amount of
SPREAD applied. For example, with a 90 degree setting, the rst voice
will always be at 0 degrees, and each consecutive voice will be shifted
by an additional 90 degrees. So with 4 voice UNISON, voice 1 would be
at 0 degrees, voice 2 would be at 90 degrees, voice 3 would be at
180 degrees, and voice 4 would be at 270 degrees.
The PHASE SPREAD range is from 1-254 degrees.
The default PHASE setting is POLY.
5. To exit the LFO EDIT menu, press the EDIT switch again (or press the PROG
switch) to return the main display.
LFO (KEY SYNC OFF)
KEY GATE
LFO (KEY SYNC ON)
LFO KEY SYNC
LFO (ARP SYNC OFF)
ARP CLOCK
LFO (ARP SYNC ON)
LFO ARP SYNC
0
85
170
LFO SLEW RATE
255
45
90
180
225
LFO PHASE SPREAD (UNISON 4 SHOWN)
VOICE 1 LFO VOICE 2 LFO VOICE 3 LFO VOICE 4 LFO