Manual
Table Of Contents
- Thank you
- Important Safety Instructions
- Legal Disclaimer
- Limited warranty
- About the DeepMind 12
- 1. Introduction
- 2. Features
- 3. Controls
- 4. Program Management
- 5. Playing Guide
- 6. Signal Path / Voice Structure
- 7. Menu System
- 8. Programming
- 9. Effects Reference Guide
- 10. Short-cuts
- 11. Applications
- 12. DAW MIDI Configuration
- 13. System Block Diagram
- 14. Connection Wiring Diagrams
- 15. Technical Specifications
- 16. MIDI Commands
- 17. MIDI NRPN Commands
- 18. Global Commands
- 19. MIDI SysEx Commands
- 20. Firmware Update
- 21. Troubleshooting
- 22. Bootloader Menu
- 23. Definition of Terms
- 24. Appendix 1 - Octave Shifting
- 25. Appendix 2 - ARP/SEQ/LFO Sync Timing
- 26. Appendix 3 - Poly Chords
- 27. Appendix 4 - Default Program
- 28. Appendix 5 - Revert to Panel
70 DeepMind 12 User Manual
8.3.11 OSC EDIT SWITCH (OSC 1)
1. To access the OSC1 PARAMETERS EDIT menu, press the OSC EDIT switch once.
2. The OSC EDIT switch will then start ashing and the OSC 1 PARAMETERS
menu will appear as shown:
3. To navigate the options in the OSC 1 EDIT menu, use the BANK/UP or BANK/
DOWN switches.
4. Selected parameters are adjusted using the -/NO or +/YES switches, the
rotary knob or the DATA ENTRY fader. The rotary knob has a click which
allows very accurate control. The fader allows rapid adjustment across the
full range.
Note: If you want to access the OSC 2 EDIT menu, press the EDIT switch
again.
Shortcut Note: To quickly change any of the OSC Modulation sources, press
and hold down the OSC EDIT switch, and use the PITCH MOD faders to change
the PITCH MOD sources, or use the PWM fader to change the OSC1 PWM
source, and the TONE MOD fader to change the OSC2 TONE MOD source.
The following options are available in the OSC 1 EDIT menu:
• RANGE - This option allows you to select the base pitch of the OSC as follows:
• 16' - The lowest note on the keyboard (C) is tuned to 16.35 Hz.
• 8' - The lowest note on the keyboard (C) is tuned to 32.7 Hz.
• 4'- The lowest note on the keyboard (C) is tuned to 65.4 Hz.
The default setting for the RANGE is 8'.
FLASHING=EDIT
• P. M O D -SRC - This option allows you to select the source for the amount of
PITCH MODULATION from the following:
• LFO-1 - Bipolar use of the LFO 1 waveform.
• LFO-2 - Bipolar use of the LFO 2 waveform.
There is also a visualization of the modulation as shown below. The arrows
indicate the polarity of the modulation.
• ENV-1 - Unipolar use of the ENV 1 envelope.
• ENV-2 - Unipolar use of the ENV 2 envelope.
• ENV-3 - Unipolar use of the ENV 3 envelope.
Note: In the visualization for ENVELOPE sources, the arrow will only point in
the UP direction indicating that the modulation will be positive from the
base pitch.
OSC 1 (SAW)
LFO (SIN)
PITCH MOD
OSC 1 PITCH MODULATION (LFO AS SOURCE)
OSC 1 (SQR)
LFO (SIN)
PITCH MOD
OSC 1 PITCH MODULATION AMOUNT (ENVELOPE AS SOURCE)
OSC 1 (SQR)
ENVELOPE
ATTACK DECAY
SUSTAIN
RELEASE
PITCH MOD