Manual
Table Of Contents
- Thank you
- Important Safety Instructions
- Legal Disclaimer
- Limited warranty
- About the DeepMind 12
- 1. Introduction
- 2. Features
- 3. Controls
- 4. Program Management
- 5. Playing Guide
- 6. Signal Path / Voice Structure
- 7. Menu System
- 8. Programming
- 9. Effects Reference Guide
- 10. Short-cuts
- 11. Applications
- 12. DAW MIDI Configuration
- 13. System Block Diagram
- 14. Connection Wiring Diagrams
- 15. Technical Specifications
- 16. MIDI Commands
- 17. MIDI NRPN Commands
- 18. Global Commands
- 19. MIDI SysEx Commands
- 20. Firmware Update
- 21. Troubleshooting
- 22. Bootloader Menu
- 23. Definition of Terms
- 24. Appendix 1 - Octave Shifting
- 25. Appendix 2 - ARP/SEQ/LFO Sync Timing
- 26. Appendix 3 - Poly Chords
- 27. Appendix 4 - Default Program
- 28. Appendix 5 - Revert to Panel
106 DeepMind 12 User Manual
ChorusVerb (CHORUS & REVERB)
No DM12 REF PARAMETER UNITS MIN MAX DESCRIPTION
1* SPD Speed Hz 0.0 Hz 4.0 Hz Adjusts the rate of the chorus. Time synchronised options from 4 to 1/64 bars.
2* DEP Depth % 0.0% 100% Adjusts the modulation depth of the chorus.
3 DLY Delay ms 0.5 ms 50.0 ms Adjusts the delay of the chorus.
4* PHS Phase — 0.0 180.0 Osets the phase between the left and right channels.
5 WAV Wave % 0.0% 100% Adjusts the LFO waveform from a sine wave to triangular wave.
6* BAL Balance — -100.0 100.0 Adjusts the balance between chorus and reverb.
7 PRE PreDelay ms 0.0 200.0 ms Controls the amount of time before the reverb is heard following the source signal.
8* DCY Decay s 0.1 s 5.0 s Controls the amount of time it takes for the reverb to dissipate.
9 SIZ Size — 2.0 200.0 Controls how large or small the simulated space is.
10* DMP Damping Hz 1000 Hz 20000 Hz Determines the decay of high frequencies within the reverb tail.
11* LC LoCut Hz 10.0 Hz 500.0 Hz Excludes low frequencies below the value.
12* MIX Mix % 0.0% 100% Controls the mix (or ratio) of wet (processed) and dry (unprocessed) signals.
* These parameters are available as modulation destinations in the Modulation Matrix
DelayVerb (DELAY & REVERB)
No DM12 REF PARAMETER UNITS MIN MAX DESCRIPTION
1 TIM Time ms 1.0ms 1500.0ms Adjusts the delay time for the left channel delay. Time sync options from 4 to 1/64 bars.
2 PAT Pattern — 1/4 1X Sets the delay ratio for the right channel delay.
3* FHC FeedHC Hz 200.0 Hz 20000.0 Hz Trims high frequencies from the feedback.
4* FBK Feedback % 0.0% 100% Controls the percentage of feedback.
5* XFD X-Feed % 0.0% 100% Control the amount of delay sound sent to the reverb eect.
6* BAL Balance — -100.0 100.0 Adjusts the ratio between delay and reverb.
7 PRE PreDelay ms 0.0 200.0 ms Controls the amount of time before the reverb is heard following the source signal.
8* DCY Decay s 0.1 s 5.0 s Controls the amount of time it takes for the reverb to dissipate.
9 SIZ Size — 2.0 200.0 Controls how large or small the simulated space is.
10* DMP Damping Hz 1000 Hz 20000 Hz Determines the decay of high frequencies within the reverb tail.
11* LC LoCut Hz 10.0 Hz 500.0 Hz Excludes low frequencies below the value.
12* MIX Mix % 0.0% 100% Controls the mix (or ratio) of wet (processed) and dry (unprocessed) signals.
* These parameters are available as modulation destinations in the Modulation Matrix