TDS

TECHNICAL DATA SHEET
This information is provided "as is" and no representations or warranties, either express or implied, of merchantability, fitness for a particular purpose or of any other
nature are made with respect to this information or to any product referred to in this information. For SDS or to consult with a Behr Paint Company representative, call
1-800-854-0133 Ext. 2 (U.S.A. only). ©2020 Behr Process Corporation, Santa Ana, CA 92705 U.S.A.
Revised 1/2020
PRODUCT INFORMATION
BEHR ® Fast-Drying Water-Based Polyurethane is designed to provide a crystal clear self-leveling smooth finish that protects
and beautifies interior wood surfaces. This product has less odor than oil-based finishes and resists stains and scratches.
Available in four sheens: Matte, Satin, Semi-Gloss and Gloss.
RECOMMENDED USES:
Ideal for properly prepared interior bare or stained surfaces such as furniture, moldings, cabinets, trim and wood doors.
CAUTION: Topcoated surfaces may be slippery when wet.
PRODUCT SPECIFICATIONS:
Finish : Matte: 5–15 @ 60°
Satin: 20–30 @ 60°
Semi-Gloss: 50–60 @ 60°
Gloss: 5> 85 @ 60°
Resin Type: Polyurethane/Acrylic
Weight per Gallon: 8.4 lb
% Solids by Volume: 29 % ± 2%
% Solids by Weight: 30 % ± 2%
VOC: < 275 g/L
Flash Point: N/A
Viscosity: 7-15 s (Zahn #3 cup)
Recommended Film Thickness:
Wet: 2.8 mils / Dry: 0.8 mils @ 500 sq ft/gal per coat
For maximum durability, 3 coats are required.
Coverage: Up to 500 sq ft/gal, depending on application
method and substrate porosity.
APPLICATION:
To Touch: 1 hr
Sand or Recoat: 1 hr
Light Use: 12–24 hrs
Full Cure: 72 hrs
SURFACE PREPARATION:
FAST DRYING WATER-BASED POLYURETHANE
R
NO. B8100 SERIES
COMPLIES WITH THE BELOW AS OF 1 /1/20 20
SCAQMD YES
AIM
YES
CARB SCM 2007 YES
CARB YES YES
OTC PHASE II YES
OTC
YES
LADCO
CAUTIONS/LIMITATIONS:
• Protect from freezing.
• Product appears milky when wet but dries to a crystal
clear finish.
• Do not use a belt or drum-type sander for sanding
between coats.
• Avoid heavy traffic and replacing of furniture for 72
hours after final coat. When replacing furniture, do not
slide. Do not install rugs or clean floors for 7 days.
• Shelf life under normal conditions is 2 years unopened.
All surfaces must be clean, free of dust, oil, grease, wax,
polish , glue and all other foreign substances.
For refinishing, remove all wax or cleaner build-up with a wax
stripper or degreaser prior to sanding. Sand all surfaces in the
direction of the wood grain to desired smoothness. DO NOT
USE steel wool. Remove all dust from sanded surfaces.
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA vacuum
and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead
Information Center at 1-800-424-LEAD or log on to
www.epa.gov/lead.
CLEAN-UP/DISPOSAL:
Clean all tools and equipment with warm, soapy water. Do
not dispose of this product down a drain. If spilled, contain
material and remove with an inert absorbent. Dispose of
contaminated absorbent, container and unused produc in
accordance with all current federal, state and local
regulations. For recycling or disposal of empty containers,
unused product and soiled rags, contact your household
refuse collection service.
GENERAL INFORMATION:
CAUTION IRRITANT CONTAINS: PARAFFIN AND
HYDROCARBON WAXES. MAY CAUSE EYE, SKIN, NOSE AND
THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES
AND AVOID BREATHING VAPORS AND SPRAY MIST. WEAR
EYE PROTECTION AND PROTECTIVE CLOTHING. USE WITH
ADEQUATE VENTILATION. To avoid breathing vapors and
spray mist, open windows and doors or use other means to
ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase
fresh air. If properly used, a respirator (NIOSH-approved for
organic vapor with P series particulate pre-filter) may offer
additional protection; obtain professional advice before
using. A dust mask does not provide protection against
vapors. Avoid contact with eyes and skin. Wash thoroughly
after handling. Close container after each use. FIRST AID: If
you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get
medical assistance immediately. In case of eye contact, flush
immediately with plenty of water for at least 20 minutes
and get medical attention; for skin, wash thoroughly with
soap and water. If swallowed, get medical attention
immediately. CAUTION: KEEP OUT OF REACH OF
CHILDREN-DO NOT TAKE INTERNALLY.
Dry Time: @ 77°F & 50% RH
Longer dry time may be required in cooler temperatures and
higher humidity.
Stir thoroughly prior to and during use. Do not shake or thin.
Using a high quality nylon brush, dip approximately an inch
into the can, gently tapping it against the inside to remove
any excess. Apply a thin, even coat following the direction of
the grain making sure to maintain a wet edge. To minimize
the brush marks and bubbles after staining application, tip
off the surface by holding the brush at a 45 degree angle and
lightly run the bristles over the entire length of the wood.
Floor Application: use a synthetic pad applicator or nylon/
polyester brush and maintain a wet edge to avoid lap marks.
Do not puddle, over-brush or overlap finishes. Sand lightly
between coats with fine sandpaper. Remove all dust prior to
applying additional coats.
Brush: Nylon/polyyester brush
Thinning: Do not thin. Product is formulated for use at
package consistency only.